ACME LED-PS10D RGBW Manual de usuario

10W LED COLOR SPOT

LED-PS10D RGBW

User Manual

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Installation

4. How to Control the Unit

4.1 Control Panel

4.2 Master/Slave operation

4.2 Easy controller

4.4 Universal DMX controller

5. DMX 512 Configuration

6. DMX 512 Connection

7. Trouble Shooting

8. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Manual for future consultation. If you sell the unit to another

user, be sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only and use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect mains power before fuse replacement or servicing.

yReplace fuse only with the same type.

yMake sure there are not flammable materials close to the unit while operating as it is

fire hazard.

yUse safety cable when fixes this unit.

yMaximum ambient temperature is TA: 40 ℃and don’t operate it where the

temperature is higher than this.

yUnit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand

during its operation.

yThere are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact the nearest authorized technical assistance center and always use the

same type spare parts. .

yDon’t connect the device to any dimmer pack or power pack.

yDo not look directly at the LED light beam while the fixture is on.

yThe housing must be replaced if they are visibly damaged.

yDo not touch any wire during operation as high voltage might be causing electric

shock.

2. Technical Specification

yFeatures a 10W quad-color high-powered LED, creating vivid colors that are suitable

for mirror ball projection or for color changing performance

y3 Operation Mode: DMX, Master/Slave & Sound Active

yOptional easy controller CA-8 or CA-9 RTX for instant lighting shows at your

fingertips.

yNo heat, low power consumption, no duty cycle, runs all night

yIdeal for clubs, bars, discos, parties, mobiles DJs, etc

Please read the instruction carefully which including

important information about the installation,

yVoltage: AC 100-240V~50/60Hz

yLED: 1 x 10W quad-color LED, 50,000 hrs rated

yPower Consumption: 14.9W

yDimension: 187 x 156 x 115 mm

yWeight: 2.0kg

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of

10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

4. How To Control The Unit

4.1 Control Panel

○

1Hanging bracket: With 2 knobs on both sides to fasten the unit and a mounting hole

to fix a mounting hook

○

2Optical Lens: Turn the lens to change the focus and obtain sharp gobos

○

3DIP Switches: Set the different function settings

○

4Microphone: Receives the sound to control the unit

○

5○

6Only for remote control:

Connecting with CA-8/CA-9/CA-9RTX to control the unit for Stand by, Function and

Mode.

○

7Safe Ring: For attached the safe cable.

○

8Heat sink for the LED: Do not cover this part to ensure proper cooling.

○

9DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

○

10DMX output: For DMX512 link, use 3-pin XLR plug cable to link the next unit..

○

11Mains input: Connect to power supply.

4.2 Master/Slave Operation

The unit can be linked together in daisy chain as many as you need in master/slave mode,

the first unit will control the others to give a coordinate automatic light show and it’s good

for instant shows.

In Master/Slave mode refer to the DMX settings below:

Master unit: Set DIP switch 1-9 to OFF.

Slave units: The DMX start address may set to any value but 0.

Î4-Light show

Set dip switch 1-9 to OFF for the first unit which has nothing in its DMX input jack. Set the

DMX address of other units to 1,4,7 or 10 when the dip switch 10 OFF, or set the DMX

address of other units to 1,5,9 or 13 when the dip switch 10 ON, then the units (slave) will

follow the first unit (master) to run built-in program for

4-Light show. The slave units which don’t set the

address as mentioned aforementioned will run as

slave 1.

Dip switch 10 OFF

Slave 1：dip / on: #1 (=1)

Slave 2：dip / on: #3 (=4)

Slave 3：dip / on: #1,#2, #3 (1+2+4=7)

Slave 4：dip / on: #2, #4 (2+8=10)

Dip switch 10 ON

Slave 1：dip / on: #1 (=1)

Slave 2：dip / on:, #1, #3 (1+4=5)

Slave 3：dip / on: #1, #4 (1+8=9)

Slave 4：dip / on: #1, #3, #4 (1+4+8=13)

4.3 Easy Controller (by CA-8/CA-9/CA-9RTX)

The easy remote control is used only in master/slave mode. By connecting to the 4-pin

jack of the first unit, you will find that the remote controller on the first unit will

control all the other units for Stand by, Function and Mode selection

Blackout Blackout the unit

Function

Strobe

1.Synchronous strobe in

white

2.Sound strobe in white

3.Sound strobe in color

Select color

1. Red

2. Green

3. Blue

4. White

5. Red + Green

6. Red + Blue

7. Red + White

8. Green + Blue

9. Green + White

10. Blue + White

11. Red + Green + Blue

12. Red + Green + White

13. Red + Blue + White

14. Green + Blue + White

15. Red + Green + Blue +

White

16. Color change by sound

Mode Sound (LED OFF) Manual Color (LED ON)

4.4 Universal DMX Controller

When using a universal DMX controller to control the chain of units, you can set DIP

switch 10 OFF to select 3 channels mode and set it ON to select 4 channels mode. After

choosing channel mode, you have to set DMX address by Dip switches from 1 to 9 to

make sure all the units will receive its DMX signal. Please refer to the following diagram

to know how to address your DMX 512 system in the binary code.

DMX 512 Address Chart:

Dip-switch

es # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10

Value 1 2 4 8 16 32 64 12

8 25

6 Channel

mode

Dip switch 10 OFF

Channel 1：dip / on: #1 (=1)

Channel 2：dip / on: #3 (=4)

Channel 3：dip / on: #1,#2, #3 (1+2+4=7)

Channel 4：dip / on: #2, #4 (2+8=10)

Dip switch 10 ON

Channel 1：dip / on: #1 (=1)

Channel 2：dip / on:, #1, #3 (1+4=5)

Channel 3：dip / on: #1, #4 (1+8=9)

Channel 4：dip / on: #1, #3, #4 (1+4+8=13)

5. DMX 512 Configuration

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the unit to

the input of the next unit. The cable can not be branched or split to a ‘Y’ cable. DMX

512 is a very high-speed signal. Inadequate or damaged cables, solder joints or

corroded connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when power is connected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-512 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

8. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

9. 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

10. Pin 4/5: Not used.

7. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The fixture does not work, no light

11.Check the connection of power and main fuse.

12.Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. Check the LED for the response of the master/ slave mode signal.

2. Check if the unit is receiving DMX signal and cut it off.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

Tabla de contenidos

Otros manuales de Equipo de iluminación de ACME

ACME

ACME Sandane Manual de usuario

ACME

ACME Andromeda Manual de usuario

ACME

ACME Thunderroar Manual de usuario

ACME

ACME GEIST BSWF Manual de usuario

ACME

ACME LED Move 600SE Manual de usuario

ACME

ACME DOT Manual de usuario

ACME

ACME SABER HYBRID PRO Manual de usuario

ACME

ACME LED-275 D Manual de usuario

ACME

ACME Uploader II Manual de usuario

ACME

ACME SABER Mini Manual de usuario

ACME

ACME LED-SC25 Manual de usuario

ACME

ACME iSolution Manual de usuario

ACME

ACME LED-SC252 Manual de usuario

ACME

ACME DELUGE LED-WAV-50W Manual de usuario

ACME

ACME Diamonds II Manual de usuario

ACME

ACME Pageant CM-200Z Manual de usuario

ACME

ACME Thunderstruck LP-2304 Manual de usuario

ACME

ACME Libre Manual de usuario

ACME

ACME Spartan Hybrid Manual de usuario

ACME

ACME CRUX Manual de usuario

ACME

ACME BP-183 RGBW S R DXX Manual de usuario

ACME

ACME COMET Manual de usuario

ACME

ACME Thunderbreaker Manual de usuario

ACME

ACME LED-PS10 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario