ACME Andromeda Manual de usuario

CONTENTS

1. Safety Instructions............................................................................................. 2

2. Technical Specifications..................................................................................... 4

3. Control Panel..................................................................................................... 6

4. Effect Wheels and Lamp.................................................................................... 7

4.1 Effect Wheels...............................................................................................7

4.2 Replacing Rotating Gobos........................................................................... 8

4.3 Light Source............................................................................................... 10

4.4 Change The Lamp...................................................................................... 10

4.5 Lamp Replacement Warning..................................................................... 12

5. How To Set The Unit........................................................................................ 12

5.1 Main Function............................................................................................12

5.2 Home Position Adjustment....................................................................... 20

6. Control By Universal DMX Controller..............................................................24

6.1 DMX512 Connection................................................................................. 24

6.2 Address Setting..........................................................................................25

6.3 DMX512 Configuration..............................................................................25

7. Error Information.............................................................................................31

8. Troubleshooting...............................................................................................37

9. Fixture Cleaning............................................................................................... 38

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully to ensure that there is no transportation damage before using the

unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.

Before operation, ensure that you are connecting this product to the proper voltage in

accordance with the specifications in this manual or on the product’s specification label.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0 ℃. Maximum ambient temperature TA: 40 ℃. Do not

operate this product at a lower or higher temperature.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Keep flammable materials away from the fixture while operating to avoid fire hazard.

Make sure the power cord is not crimped or damaged; replace it immediately if damaged.

Unit’s surface temperature may reach up to 75 ℃. DO NOT touch the housing bare-handed

during its operation.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off

the mains power immediately.

DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid entanglement of the power cord with other wires.

The minimum distance to objects/surface must be more than 12 meters.

Disconnect mains power before fuse/lamp replacement or servicing.

Replace fuse/lamp only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the housing as there are no user serviceable parts inside.

DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center if needed.

Disconnect this product from its power source before servicing.

DO use the original packaging if the device is to be transported.

Hot lamp explosion hazard. DO NOT open the unit within 15 minutes after switching off.

DO replace the bulb once it is damaged, deformed or life-expired.

Avoid direct eye exposure to the light source while the product is on.

Never touch bulb with bare fingers, as it is very hot after using.

DO NOT operate this product if you see damage on the housing, shields, or cables. Have the

damaged parts replaced by an authorized technician at once.

Installation:

The fixture should be fixed on the clamp. Always ensure that the unit is firmly fixed to avoid

vibration and slipping off during operation. Ensure that the trussing or area of installation must be

able to hold 10 times the weight without any deformation. Always install a safety cable that can

hold at least 12 times the weight of the fixture when installing.

DO install and operate by qualified operator. It must be installed in a place where there is out of the

reach of people.

2. Technical Specifications

Power Voltage:

100-240V~ 50/60Hz

Power Consumption:

695W

Light Source:

PHILIPS MSD Platinum 400L Flex

Color Temperature:

7800K

Zoom Range:

Beam Mode: 2°~7°

Spot Mode: 5°~34°

Wash Mode: 8°~70°

Movement:

Pan: 540°

Tilt: 270°

Pan/Tilt Resolution: 16 bit

Fixation: Tilt lock

Dimmer/Shutter:

Smooth dimming from 0-100%; outstanding strobe effect with variable speed

Color Wheel:

1 x color wheel with 14 fixed colors plus open, and rainbow effect

Gobo Wheel:

1 x static gobo wheel with 16 gobos plus open (two optical aperture)

1 x rotating gobo wheel with 7 gobos plus open, convenient replacement

Control:

DMX Channel: 26/19 channels

Control Mode: DMX512, RDM

Firmware upgrade via DMX link or USB Disk

Construction:

Display: LCD display

Battery backup for user setup without mains connection

Data In/Out: 3-pin XLR (5-pin XLR is optional)

Power In/Out: Power Cord in; Power Connector in/out

Protection Rating: IP20

Features:

Lamp life: 6000 hours

Motorized focus

Linear CMY color mixing + Variable CTO

1 x animation wheel with outstanding water and flame effect, the wheel can be replaced

2x prisms: 8-facets prism+6-facets linear prism, rotatable in both directions and overlayable

Independent frost effect

2x fixed clamps for 50mm truss

Dimension/Weight:

402x308x725mm, 30.5kgs

15.8"x12.1"x28.5"in, 67.2lbs

Photometric Diagram:

3. Control Panel

1. Display: To show the various menus and the selected functions

2. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To go forward to move down in the menu

ENTER

To perform the desired functions

3. FIRMWARE UPGRADE: Used to upgrade fixture’s firmware

4. BATTERY DISPLAY

5. DMX IN:

For DMX512 link, use 3-pin XLR cable to link the unit and DMX controller (5-pin XLR is optional)

6. DMX OUT:

For DMX 512 link, use 3-pin XLR cable to link the next units (5-pin XLR is optional)

7. POWER IN: To connect to supply power

8. FUSE(T 15A): Protects the unit from damage of over-voltage or short circuit

9. POWER SWITCH: Turns on/off the power

4. Effect Wheels and Lamp

4.1 Effect Wheels

DANGER!

Install the rotating gobos with the device switched off only.

Unplug from mains before changing the rotating gobos!

CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be

opened!

R-Gobos

Part Number

1Gobo1

3011001305

2Gobo2

3011001167

3Gobo3

3011001308

4Gobo4

3011001307

5Gobo5

3011001306

6Gobo6

3011001168

7Gobo7

3011001169

4.2 Replacing Rotating Gobos

1. Unscrew the four screws at A and unplug the two sets of DB head cables at B to take out the

component;

2. Unscrew the three screws at C and remove the fan; then unscrew the five screws at D to take out

the component; unscrew the three screws at E;

3. Unscrew the three screws at F and remove the plastic gear; Clamp out the circlip at G to take out

the rotating gobo wheel component;

4. Gently lift the gobo holder from the edge of the rotating gobo wheel (reverse side) as H shows

and slowly pull it out;

5. Remove the spring lock at I with an appropriate tool like tweezers (if the gobo is coated with glass

glue, do remove it with some good glass cleaning fluid before removing the spring lock to avoid

damage to the gobo).

6. Do not touch the surface of the gobo with bare fingers. The gobo has a small position point at its

edge which has to aim at the position point on the gobo holder like J shows (glossy side towards the

light source).

7. Insert the gobo holder back into the rotating gobo wheel component in this way that its position

point has to exactly aim at the center of the rotating gobo wheel.

8. After installation, put the component back to the fixture.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de ACME

ACME

ACME LED-3082 RGB Manual de usuario

ACME

ACME Xperior 1500SZ Manual de usuario

ACME

ACME LED-WAV-10W Manual de usuario

ACME

ACME LED-HC101 II Manual de usuario

ACME

ACME Solar Flare Manual de usuario

ACME

ACME LP-F1000 CW Manual de usuario

ACME

ACME V-BOX Manual de usuario

ACME

ACME DELUGE LED-WAV-50W Manual de usuario

ACME

ACME LED-0408 Manual de usuario

ACME

ACME CHIRON Manual de usuario

ACME

ACME Beluga Manual de usuario

ACME

ACME LED-PS10 Manual de usuario

ACME

ACME Neozone Manual de usuario

ACME

ACME LED-212RGB Manual de usuario

ACME

ACME Diamonds II Manual de usuario

ACME

ACME LED-SC25 Manual de usuario

ACME

ACME LED-900 A Manual de usuario

ACME

ACME STAGE PAR 100 COLOUR IP Manual de usuario

ACME

ACME Stag Par MP-200 Manual de usuario

ACME

ACME DIABOLO 500 Manual de usuario

ACME

ACME DAZZLED COLORLED-430 Manual de usuario

ACME

ACME LED-835B Manual de usuario

ACME

ACME Inferno Manual de usuario

ACME

ACME Spartan Hybrid Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario