ACME LED Move 600SE Manual de usuario

LED‐MS600SE



UserGuide

ProfessionalLEDMovingHead

CONTENTS



1.SafetyInstruction..............................................................................................2

2.TechnicalSpecifications ....................................................................................3

3.HowToSetTheUnit .........................................................................................4

3.1ControlPanel ..............................................................................................4

3.2GoboWheel................................................................................................5

3.3MainFunction.............................................................................................6

3.4HomePositionAdjustment.......................................................................11

4.ControlByUniversalDMXController .............................................................14

4.1DMX512Connection................................................................................14

4.2DMXAddressSetting ................................................................................15

4.3DMX512Configuration .............................................................................16

5.Troubleshooting..............................................................................................18

6.FixtureCleaning..............................................................................................20

1.SafetyInstruction

WARNING

PleasekeepthisUserGuideforfutureconsultation.Ifyouselltheunittoanotheruser,besure

thattheyalsoreceivethisinstructionmanual.

Important:

Damagescausedbythedisregardofthisusermanualarenotsubjecttowarranty.The

dealerwillnotacceptliabilityforanyresultingdefectsorproblems.

yUnpackandcheckcarefullythatthereisnotransportationdamagebeforeusingtheunit.

yTheunitisforindooruseonly.Useonlyinadrylocation.

yDOinstallandoperatebyqualifiedoperator.

yDONOTallowchildrentooperatethefixture.

yUsesafetychainwhenfixingtheunit.Handletheunitbycarryingitsbaseinsteadofhead

only.

yTheunitmustbeinstalledinalocationwithadequateventilation,atleast50cmfromadjacent

surfaces.

yBesurethatnoventilationslotsareblocked,otherwisetheunitwillbeoverheated.

yBeforeoperating,ensurethatthevoltageandfrequencyofpowersupplymatchthepower

requirementsoftheunit.

yIt’simportanttogroundtheyellow/greenconductortoearthinordertoavoidelectricshock.

yMaximumambienttemperatureTa:40℃.DONOToperateitwhenthetemperatureishigher.

yDONOTconnectthedevicetoanydimmerpack.

yDuringinitialstart‐upsomesmokeorsmellmayarise.Thisisanormalprocessanddoesnot

necessarilymeanthatthedeviceisdefective,anditwilldecreasegraduallywithin15minutes.

yMakesuretherearenoflammablematerialsclosetotheunitwhileoperatingtoavoidfire

hazard.

yExaminethepowerwirescarefully,replacethemimmediatelyifthereisanydamage.

yUnit’ssurfacetemperaturemayreachupto85℃.DONOTtouchthehousingbare‐handed

duringitsoperation,andallowabout15minutesforcoolingtheunitdownbeforereplacing

bulbormaintenanceasitcouldbeveryhot.

yAvoidanyinflammableliquids,waterormetalobjectsenteringtheunit.Onceithappens,cut

Pleasereadcarefullytheinstruction,whichincludesimportant

informationabouttheinstallation,usageandmaintenance.

offthemainspowerimmediately.

yDONOToperateindirtyordustyenvironment,docleanfixturesregularly.

yDONOTtouchanywireduringoperationastheremightbeahazardofelectricshock.

yAvoidpowerwirestogethertwistothercables.

yTheminimumdistancebetweenlightoutputandtheilluminatedsurfacemustbemorethan

2.5meters.



yDisconnectmainspowerbeforefuse/lampreplacementorservicing.

yReplacefuse/lamponlywiththesametype.

yIntheeventofseriousoperatingproblem,stopusingtheunitimmediately.

yNeverturnonandofftheunittimeaftertime.

yThehousing,thelenses,ortheultravioletfiltermustbereplacediftheyarevisiblydamaged.

yDONOTopentheunitastherearenouserserviceablepartsinside.

yNevertrytorepairtheunitbyyourself.Repairscarriedoutbyunskilledpeoplecanleadto

damageormalfunction.Pleasecontactthenearestauthorizedtechnicalassistancecenterif

needed.

yDisconnectthemainspowerifthefixtureishasnotbeenusedforalongtime.

yDOusetheoriginalpackingmaterialsbeforetransportingitagain.

Caution：

yTopreventorreducetheriskofelectricalshockorfire,donotexposetheunittorainor

moisture.

yHotlampexplosionhazard.Donotopentheunitwithin15minutesafterswitchingoff.

yDOreplacethebulbonceitisdamaged,deformedorlife‐expired.

yDONOTlookdirectlyatthelightwhilethebulbison.

yNevertouchbulbwithbarefingers,asitisveryhotafterusing.

yDONOTstartontheunitwithoutbulbenclosureorwhenhousingisdamaged.

2.TechnicalSpecifications

yDMXChannels:14&15channels

yGreatbuilt‐inlightingshowsunderMaster/Slavemodetriggeredbymusic

ySmooth0~100%dimmingandvariablestrobespeeds

yMotorizedfocusbyDMXcontrol

yAutomaticPan/Tiltpositioncorrection

yExcellentventilation,ensuringreliableoperation

yVoltage：AC100‐240V~50/60Hz

yPowerconsumption:226W

yLightSource:1x150WLED

yFuse:6.3A

yDimension:327x247x526mm

yWeight:14Kgs

3.HowToSetTheUnit

3.1ControlPanel

FrontviewRearview

① Display:

Showthevariousmenusandtheselectedfunctions

②LED:

DMXOnDMXinputpresent

MASTEROnMasterMode

SLAVEOnSlaveMode

SOUNDFlashingSoundactivation



③Button:

MENUToselecttheprogrammingfunctions

DOWNTogobackwardintheselectedfunctions

UPTogoforwardintheselectedfunctions

ENTERTo confirmtheselectedfunctions

④OnlyForRemoteControl:

ConnectingwithCA‐8/ C A ‐9RTXtocontroltheunitforStandby,FunctionandModefunction.

⑤DMXinput/output:

ForDMX512link,use3/5 ‐pinXLRplugcabletolinktheunittogether.

⑥Mainsinput:

Connecttosupplymainspower.

⑦Mainsoutput:

Connecttosupplymainspowerforthenextunit.

3.2GoboWheel

DANGER!

Installthegoboswiththedeviceswitchedoffonly.

Unplugfrommainsbeforechanginggobos!

3.3MainFunction

Toselectanyofthegivenfunctions,presstheMENUbuttonuptowhentherequiredoneis

showingonthedisplay.SelectthefunctionbyENTERbuttonandthedisplaywillblink.UseDOWN

andUPbuttontochangethemode.Oncetherequiredmodehasbeenselected,PressENTER

buttontostore.BacktothemainfunctionswithoutanychangepresstheMENUbuttonorwaitfor

8seconds.

HoldMENUbuttontoquitmenumode,theunitwillrunthebuilt‐inprogramyouselected.

Themainfunctionsareshownbelow:

DMXAddress

SelectDMXAddress,presstheENTERbuttontoconfirm,thepresentaddresswillblinkonthe

display.UsetheUPandDOWNbuttontoadjusttheaddressfrom1to512.Oncetheaddresshas

beenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychange

presstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwaitforone

minutetoexitthemenumode.



ChannelMode

SelectChannelMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.

UsetheDOWNandUPbuttontoselectthe14Chor15ChMode.Oncethemodehasbeen

selected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychangepress

theMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwaitforone

minutetoexitthemenumode.



ShowMode

SelectShowMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheShow1orShow2orShow3orShow4mode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SlaveMode

SelectSlaveMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheSlave1(normal)orSlave2(2lightshow)mode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



BlackoutMode

SelectBlackoutMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.

UsetheDOWNandUPbuttontoselecttheM/S(Master/Slave),HoldorBlackoutMode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SoundState

SelectSoundState,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheOn(soundon)orOff(soundoff)mode.Oncethemode

hasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SoundSense

SelectSoundSense,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.

UsetheDOWNandUPbuttontochangethesoundsensefrom0…100.Oncethemodehasbeen

selected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychangepress

theMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwaitforone

minutetoexitthemenumode.



PanInverse

SelectPanInverse,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheYes(paninversion)orNo(normal)mode.Oncethemode

hasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de ACME

ACME

ACME Solar Flare Manual de usuario

ACME

ACME PIXEL LINE IP Manual de usuario

ACME

ACME Solaris Manual de usuario

ACME

ACME PEXEL 100 Manual de usuario

ACME

ACME Sunrise Manual de usuario

ACME

ACME DELUGE LED-WAV-50W Manual de usuario

ACME

ACME XP-280 BS Manual de usuario

ACME

ACME Building wash Manual de usuario

ACME

ACME BRIGHT Manual de usuario

ACME

ACME Whack Manual de usuario

ACME

ACME LED-3082 RGB Manual de usuario

ACME

ACME LED-767 RGBW Manual de usuario

ACME

ACME LIGHT PANEL 1000 Manual de usuario

ACME

ACME SAMURAI SCAN 50 Manual de usuario

ACME

ACME Xperior XP-380 BEAM IP F Manual de usuario

ACME

ACME IL-2420 II Manual de usuario

ACME

ACME Dynamic 25 Roller LED-SC25B Manual de usuario

ACME

ACME LED STROBE 50 Manual de usuario

ACME

ACME LED-212RGB Manual de usuario

ACME

ACME Splendor 220 II Manual de usuario

ACME

ACME LS-1005 Manual de usuario

ACME

ACME LED-HC50 II Manual de usuario

ACME

ACME SABER Mini Manual de usuario

ACME

ACME TOUR PIXEL BAR 1010 II Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario