ACME Stag Par MP-200 Manual de usuario

MP-200

User Manual

Please read the manual carefully before using

CONTENTS

1. Safety Instructions..........................................................................................2

2. Technical Specifications..................................................................................3

3. How To Set The Unit ......................................................................................5

3.1 Control panel............................................................................................5

3.2 Main Functions .........................................................................................6

4. How to Control the Unit ..............................................................................12

4.1 Master/Slave Built In Preprogrammed Function ......................................12

4.2 DMX Controller ......................................................................................12

5. DMX 512 Configurations..............................................................................14

6. DMX 512 Connections .................................................................................15

7. Troubleshooting............................................................................................16

8. Fixture Cleaning............................................................................................17

1. Safety Instructions

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yMake sure there are no flammable materials close to the unit while operating as it is fire

hazard.

yUse safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but

always by taking its base.

yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool

down before replacing or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always use

the same type spare parts.

yDO NOT touch any wire during operation as high voltage might be causing electric shock.

Please read the instruction carefully, it includes important

information about the installation, usage and maintenance.

Warning:

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yDO NOT open the unit within five minutes after switching off.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact your

nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. And make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

2. Technical Specifications

◇DMX Channels: 4/5/7 channels

◇Two Operation Modes: DMX, Master/Slave

◇Excellent built-in lighting shows under Master/Slave mode

◇LED display for easy navigation

For 230V 50Hz power supply, maximum fixtures that can be connected on one power cable is 8;

For 120V 60Hz power supply, maximum fixtures that can be connected on one power cable is 4;

◇Electronic strobe smooth dimming with wash effect

◇Quad color with flicker-free

yVoltage：AC 100~240V, 50/60Hz

yPower Consumption：122W

yLED: 12pcsx10WCREELEDs

yFuse: T6.3A

yBeam Angle: 10°

yDimension：325 x 276x 344mm

yWeight：6.6Kgs

3. How To Set The Unit

3.1 Control panel

1. Mains Input: Used to connect to supply mains power for the fixture.

2. Mains Output: Used to connect to the next fixture.

3. DMX Output: Used to output the DMX signal to the next fixture by a 3-pin XLR plug cable.

4. DMX Input: For DMX512 link, use 3-pin XLR plug cable to input the DMX signal.

5. Microphone: Used to receive the Sound to control the fixture.

6. Display: Used to show the various menus and the selected functions.

LED:

7. MASTER On Master Mode

8. SLAVE On Slave Mode

9. DMX On DMX input present

10. SOUND Flashing Sound activation

Button:

11. MENU To select the programming functions

12. DOWN To go backward in the selected functions

13. UP To go forward in the selected functions

14. ENTER To confirm the selected functions

3.2 Main Functions

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

The main functions are showing below:

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to change the DMX 512 Address. Once the required address has been selected, press

the ENTER button to save or automatically return to the main functions without any change

after one minute. Back to the previous functions without any change press the MENU button.

Channel Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (4Channels:Red, Green, Blue, White), (5 Channels:Red,

Green, Blue, White, Dimmer) or (7 Channels: Red, Green, Blue, White, Color, Dimmer,

Strobe) Mode. Once the required mode has been selected, press the ENTER button to setup

or automatically return to the main functions without any change after one minute. To go

back to the functions without any change press the MENU button.

Slave Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Slave 1) or (Slave 2) mode. Once the slave mode has

been selected, press the ENTER button to setup or automatically return to the main functions

without any change after one minute. To go back to the functions without any change press

the MENU button again.

Show Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Random show) or (color) or (fade).

When you selected the , press the ENTER button, and then use the DOWN and UP

button to select the (Color 1) … (Color 9), press the ENTER button and use

the DOWN and UP button to adjust the brightness intensity from (Dimmer 0) to

(Dimmer 255); select the (Color 10), press the ENTER button, and select the

(Red), (Green),… (Dimmer), pressing the ENTER button and adjust the

brightness intensity from to .

When you selected the (Fade mode), press the ENTER button, and then use the

DOWN and UP button to adjust the fade speed from (Speed 1, the slowest) to

(Speed 3: the fastest).

Once you have finished the settings, press the ENTER button to setup or automatically exit

menu mode without any change after one minute. To go back to the last function without any

change press the MENU button.

Dimmer Mode

Press the MENU button up to when is showing on the display. Pressing the ENTER

button and the display will blink. Use the DOWN and UP buttons to select the

(Dimmer Mode 1: Optically Linear) or (Dimmer mode 2: Square Law) or

(Dimmer mode 3: Inverse Square Law) or (Dimmer mode 4: S-cure) mode. Once the

mode has been selected, press the ENTER button to setup or automatically return to the main

functions without any change after one minute. To go back to the functions without any

change press the MENU button again.

Optically Linear: The increase in light intensity appears to be linear as DMX value is

increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Tabla de contenidos

Otros manuales de Equipo de iluminación de ACME

ACME

ACME Sandane Manual de usuario

ACME

ACME Neozone Manual de usuario

ACME

ACME ColorTec 250 LED-CC60 Manual de usuario

ACME

ACME PEXEL 100 Manual de usuario

ACME

ACME LED-256D-10W Manual de usuario

ACME

ACME CM-150 PAGEANT 150 Manual de usuario

ACME

ACME Dynamic 25 Roller LED-SC25B Manual de usuario

ACME

ACME V-BOX Manual de usuario

ACME

ACME Xperior XP-380 BEAM IP F Manual de usuario

ACME

ACME FLASHDOT Manual de instrucciones

ACME

ACME Sunrise Manual de usuario

ACME

ACME Gemini Manual de usuario

ACME

ACME RAYZOR HYBRID Manual de usuario

ACME

ACME Oxygen Manual de usuario

ACME

ACME Solaris Manual de usuario

ACME

ACME BF-1500ND B Manual de usuario

ACME

ACME iSolution Manual de usuario

ACME

ACME IL-2420 II Manual de usuario

ACME

ACME LS-1005 Manual de usuario

ACME

ACME LED-PS10 Manual de usuario

ACME

ACME Spider FC Manual de usuario

ACME

ACME Dotline180 Manual de usuario

ACME

ACME CA-DC6S Manual de usuario

ACME

ACME Whack Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario