Accu-Scope EXM-150-MS Manual de usuario

MANUAL

EXM-150

MICROSCOPE SERIES

100 Lauman Lane, Suite A, Hicksville, NY 11801

Tel: (877) 877-7274 | Fax: (516) 801-2046

Email: [email protected]

www.microscopeinternational.com

'LVWULEXWHGE\

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®2

CONTENTS

SAFETY NOTES ..................................................................................................................3

CARE AND MAINTENANCE................................................................................................3

INTRODUCTION..................................................................................................................4

UNPACKING AND COMPONENTS DIAGRAMS..............................................................4-5

ADJUSMENT & OPERATION

CONNECTING THE POWER CORD......................................................................................... 6

ILLUMINATION.................................................................................................................6

SPECIMEN SLIDE.............................................................................................................7

FOCUSING.......................................................................................................................7

DISC OR IRIS DIAPHRAGM ..............................................................................................8

OIL OBJECTIVE................................................................................................................8

RECHARGING THE MICROSCOPE ..............................................................................9

FUSE REPLACEMENT...................................................................................................9

BATTERY REPLACEMENT..........................................................................................10

LED BULB REPLACEMENT.........................................................................................10

TROUBLESHOOTING...................................................................................................11-13

MAINTENANCE..................................................................................................................14

SERVICE............................................................................................................................14

WARRANTY.......................................................................................................................14

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®3

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from

dropping and being damaged.

2. Do not discard the molded Styrofoam container; the container should be retained should the

microscope ever require reshipment.

3. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

Ensure the microscope is located on a smooth, level and firm surface.

4. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may be

damaged.

5. All electrical connectors (power cord) should be inserted into an electrical surge suppressor to

prevent damage due to voltage fluctuations.

6. For safety when replacing the LED bulb or fuse, be sure the main switch is off (“O”), remove the

power cord, and replace the LED bulb after the bulb and the lamp house has completely cooled.

7. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage other than indicated will cause severe damage to the microscope.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objectives or focusing assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air stream from

an air bulb. If dirt remains on the optical surface, use a soft cloth or cotton swab dampened with a

lens cleaning solution (available at camera stores). All optical lenses should be swabbed using a

circular motion. A small amount of absorbent cotton wound on the end of a tapered stick such as

cotton swabs or Q-tips, makes a useful tool for cleaning recessed optical surfaces. Avoid using an

excessive amount of solvents as this may cause problems with optical coatings or cemented optics

or the flowing solvent may pick up grease making cleaning more difficult. Oil immersion objectives

should be cleaned immediately after use by removing the oil with lens tissue or a clean, soft cloth.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not

in use.

5. ACCU-SCOPE®microscopes are precision instruments which require periodic preventative

maintenance to maintain proper performance and to compensate for normal wear. An annual

schedule of preventative maintenance by qualified personnel is highly recommended. Your

authorized ACCU-SCOPE® distributor can arrange for this service.

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®4

INTRODUCTION

Congratulations on the purchase of your new ACCU-SCOPE® microscope. ACCU-SCOPE®

microscopes are engineered and manufactured to the highest quality standards. Your microscope will

last a lifetime if used and maintained properly. ACCU-SCOPE® microscopes are carefully assembled,

inspected and tested by our staff of trained technicians in our New York facility. Careful quality control

procedures ensure each microscope is of the highest quality prior to shipment.

UNPACKING AND COMPONENTS

Your microscope arrived pre-assembled and packed in a molded container. Do not discard the

container: the molded container should be retained for reshipment of your microscope if needed. Avoid

placing the microscope in dusty surroundings or in high temperature or humid areas as mold and mildew

will form. Carefully remove the microscope from the Styrofoam container by its arm and base and place

the microscope on a flat, vibration-free surface.

COMPONENTS DIAGRAM

Carrying Handle

Monocular Head

Eyepiece

Objective

Stage

Disc Diaphragm

Illuminator

Housing

Light Adjustment

Dial

Fine Focusing

Knob

Coarse Focusing

Knob

Nosepiece

Stage Clip

Cord Hanger

Model Shown:

EXM-150

(Models Vary)

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®5

COMPONENTS DIAGRAM

Other Models Not Shown:

EXM-150-MS

EXM-151-MST

EXM-150-T

EXM-151-MS

Y-Axis

Adjustment

(Top) Knob

X-Axis

Adjustment

(Bottom) Knob

Condenser

Models Featuring

Mechanical Stage

& Abbe Condenser

Slide Finger

Slide Holder

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®6

ADJUSTMENT & OPERATION

Connecting the Power Cord

Make sure the power switch is at “0”(OFF) before connecting.

Insert the connector ①of power cord securely into the power

socket ②.

Insert the other connector securely into an electrical outlet.

The microscope uses a universal power supply so it may

be used in any voltage range between 90 ~ 240v when

used with the appropriate line cord.

IMPORTANT: Use care when storing the power cord so

that it does not bend or twist –it is recommended to wrap

the cord around the cord hanger for storage.

Illumination

With the microscope turned on (I), rotate the light adjustment

dial ①until the illumination is comfortable for observation.

Rotate the light adjustment knob toward the back of the

microscope to increase brightness; rotate toward the front to

reduce brightness.

①

②

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®7

ADJUSTMENT & OPERATION (continued)

Placing the Specimen Slide

For Models With a Fixed Stage

Place the slide on the stage with the cover glass facing up and

secure it with the stage clips ①.

For Models With a Mechanical Stage

Push the slide finger ② of the specimen holder towards the

back to open it and place a specimen slide into the slide

holder with the cover glass facing up. Release the slide finger

so it closes and secures the slide in place.

Rotate the X and Y-axis knobs ③to move the slide into

position.

Adjusting the Focus

Turn the coarse adjustment knob ④counterclockwise to

move the stage to its lowest position.

Place a specimen slide on the center of the stage.

Using the 4x objective bring the specimen into focus using the

coarse ④and fine ⑤focusing controls.

Different objectives can be brought into view by rotating the

nosepiece and using the fine adjustment knob because the

objectives are parfocal.

①

②

③

④

⑤

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®8

ADJUSTMENT & OPERATION (continued)

Model With Iris Diagphragm

Model With Disc Diaphragm

Using the Disc or Iris Diaphragm

Each EXM-150 Series Microscope is supplied with either a

disc or iris diaphragm, depending on the model ordered.

The amount of light can be adjusted by opening or closing the

iris diaphragm (using the lever ①) or by turning the disc

diaphragm ②, located just beneath the stage).

Adjust the diaphragm to the smallest size allowable for a clear,

sharp image of the specimen.

Using the 100xR Oil Objective

(EXM-151 Models ONLY)

The procedure for examining a specimen using an oil

immersion objective is as follows:

Rotate the nosepiece so the low power objective is in the

optical path.

Place one drop of immersion oil on the lighted area of the

specimen slide ③.

Rotate the nosepiece so the 100xR oil immersion objective is

in the light path. Dust or air bubbles in the oil can destroy the

definition of the image. If the bubbles are trapped between

the objective lens and the slide, clean off the oil and start

again or try to eliminate the bubble by rotating the objective

back and forth.

With your eye at the level of the stage, use the coarse focus

knob to raise the stage with the specimen cover glass. When

you see a flash of light at this location the objective lens has

made contact with the immersion oil and the microscope can

now be focused using the fine focus knob.

IMPORTANT NOTE

Each time you finish using the oil immersion objective wipe off

all traces of oil from the objective and the specimen cover

glass with a lens tissue or clean soft cloth.

Cleaning after each use will prevent oil from contaminating the

high dry objective (40xR), prevent dust and dirt from accu-

mulating on the lens of the objective which will degrade its

optical performance, and will keep the slide clean to work with.

①

②

③

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®9

ADJUSTMENT & OPERATION (continued)

Recharging the Microscope

The LED cordless, rechargeable microscope is completely

portable and be used indoors or outdoors in any location

where there is no electrical outlet access.

The LED cordless microscope is powered by three AA

1300mAh 1.2v NiMH (Nickel Metal Hydride) rechargeable

batteries, and when used properly can sustain approximately

4 hours (depending on the light intensity/user) before a charge

is required.

Each microscope is supplied with its own 4.5v/1000A line

cord/charger and requires approximately 8 hours for a full

charge. The life expectancy of the rechargeable batteries is

approximately 20,000 hours or equivalent to 400 recharges

before needing replacement.

NOTE: Your microscope can be used while recharging.

Use ONLY the AC adapter/cord that came with your

microscope.

Replacing the Fuse

Turn the main switch to “0” (OFF) before replacing a fuse.

Unplug the power cord from the microscope.

Carefully place the microscope on the back of its arm so the

bottom of the microscope base is facing towards you.

Screw off the fuse holder ①from the bottom of the

microscope with a flat-head type screwdriver ( —).

Gently pull out the old fuse ②and Install a new fuse into the

fuse holder and screw it back into the base.

Specification of the fuse: 250V, 1.0A CAT #3277-1

①

②

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE®10

ADJUSTMENT & OPERATION (continued)

Replacing the Rechargeable Batteries

1. Unplug the microscope from the electrical outlet

(if plugged in) and unplug charger from rear of microscope

(if plugged in).

2. Carefully place the microscope on the back of its arm so

the bottom of the microscope base is facing towards you.

3. To expose the battery compartment, open the trap door on

the bottom by unscrewing the lock screw ①.

4. Using a small hex wrench, remove the screw ②on the

battery compartment and slide the cover ③toward you to

remove.

5. Replace the three NiMH AA 1300mAh rechargeable

batteries ④.

6. Slide the cover back on and replace the screw.

7. Close the trap door and tighten the lock screw.

8. Carefully place the microscope in an upright position.

9. Plug the charger to the power receptacle on the back of

the microscope and plug into an electrical receptacle for

continued use while charging.

Allow the LED microscope to charge for 8 hours before using

as cordless.

Replacing the LED Bulbs

The life expectancy of the LED bulbs is 20,000 hours.

The LED bulbs are covered by a 1 year manufacturer’s

warranty.

Should your LED bulbs need replacing, please contact an

authorized ACCU-SCOPE service center or call ACCU-

SCOPE Inc.’s technical service department at

631-864-1000 for an authorized service center near you.

IMPORTANT

USE ONLY AA 1300mAh NiMH (Nickel Metal

Hydride) rechargeable batteries in your microscope.

Using any other type of battery may damage your

microscope.

①

②

③

④

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microscopio de Accu-Scope

Accu-Scope

Accu-Scope 3078-HDR Manual de usuario

Accu-Scope

Accu-Scope EXC-400 Series Manual del propietario

Accu-Scope

Accu-Scope 3025 Series Manual de usuario

Accu-Scope

Accu-Scope 3012 Manual del propietario

Accu-Scope

Accu-Scope EXI-300 Series Manual de usuario

Accu-Scope

Accu-Scope EXC-500 Manual de usuario

Accu-Scope

Accu-Scope 3025-2 Manual del propietario

Accu-Scope

Accu-Scope 3019 Manual de usuario

Accu-Scope

Accu-Scope 3088F Manual de usuario

Accu-Scope

Accu-Scope MT-40 Series Manual de usuario

Accu-Scope

Accu-Scope 3075-GS Manual de usuario

Accu-Scope

Accu-Scope EXI-410 Series Manual de usuario

Accu-Scope

Accu-Scope 3055 Manual de usuario

Accu-Scope

Accu-Scope EXC-350-PH Manual de usuario

Accu-Scope

Accu-Scope EXM-50 Manual del propietario

Accu-Scope

Accu-Scope 3025 Manual del propietario

Accu-Scope

Accu-Scope 3025 Series Manual de usuario

Accu-Scope

Accu-Scope 3000-LED-SPH Manual de usuario

Accu-Scope

Accu-Scope 3061 Zoom Stereo Series Manual de usuario

Accu-Scope

Accu-Scope EXI-410 Series Manual de usuario

Accu-Scope

Accu-Scope EXI-600 Manual de usuario

Accu-Scope

Accu-Scope EXC-120 SERIES Manual de usuario

Accu-Scope

Accu-Scope 3078 Series Manual de usuario

Accu-Scope

Accu-Scope 3052-LED Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario