Accu-Scope 3078-HD Manual de usuario

MANUAL

73 Mall Drive, Commack, NY 11725 • 631-864-1000 (P) • 631-543-8900 (F)

www.accu-scope.com • [email protected]

3078-HD

ZOOM STEREO MICROSCOPE

MANUAL

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 2

CONTENTS

SAFETY NOTES ..................................................................................................................3

CARE AND MAINTENANCE................................................................................................3

INTRODUCTION..................................................................................................................4

UNPACKING AND COMPONENTS.....................................................................................4

COMPONENTS DIAGRAM ..................................................................................................5

ASSEMBLY..........................................................................................................................6

OPERATION .....................................................................................................................7-9

SPECIFICATIONS................................................................................................................9

TROUBLESHOOTING........................................................................................................10

MAINTENANCE..................................................................................................................11

SERVICE............................................................................................................................11

WARRANTY.......................................................................................................................11

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 3

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from

dropping and being damaged.

2. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

3. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may be

damaged.

4. LAMP REPLACEMENT -- CAUTION: the glass housing of the lamp may be extremely

hot. DO NOT attempt to change the lamp before it is completely cooled or without

wearing adequate skin protection.

5. All electrical connectors (power cord) should be inserted into an electrical surge protector to prevent

damage due to voltage fluctuations.

6. FUSE REPLACEMENT -- For safety when replacing the fuse (ONLY replace with the

same size, type and rating of original fuse), be sure the main switch is in the off position,

disconnect the power cord from outlet, and replace the fuse. Reconnect the power cord

and turn unit on.

7. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage other than indicated will cause severe damage to the microscope.

NOTE: Always plug the microscope power cord into a suitable grounded electrical outlet.

A grounded 3-wire cord is provided.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objectives or the focusing

assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air bulb. If dirt

remains on the optical surface, use a soft, lint free cloth or cotton swab dampened with a lens

cleaning solution (available at camera stores). All optical lenses should be swabbed using a circular

motion. A small amount of absorbent cotton wound on the end of a tapered stick makes a useful tool

for cleaning recessed optical surfaces. Avoid using an excessive amount of solvents as this may

cause problems with optical coatings or cemented optics or the flowing solvent may pick up grease

making cleaning more difficult.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not

in use.

5. ACCU-SCOPE®microscopes are precision instruments which require periodic servicing to maintain

proper performance and to compensate for normal wear. A regular schedule of preventative

maintenance by qualified service personnel is highly recommended. Your authorized ACCU-SCOPE®

distributor can arrange for this service.

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 4

INTRODUCTION

Congratulations on the purchase of your new ACCU-SCOPE®microscope. ACCU-SCOPE®microscopes

are engineered and manufactured to the highest quality standards. Your microscope will last a lifetime if

used and maintained properly. ACCU-SCOPE®microscopes are carefully assembled, inspected and

tested by our staff of trained technicians in our New York facility. Careful quality control procedures

ensure each microscope is of the highest quality prior to shipment.

UNPACKING AND COMPONENTS

Your microscope arrived packed in a molded shipping carton. Do not discard the carton: the shipping

carton should be retained for reshipment of your microscope if needed. Avoid placing the microscope in

dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully

remove the microscope from the shipping carton and place the microscope on a flat, vibration-free

surface.

Eyepieces

USB Cable

Audio Cable

SD Card

HDMI Cable

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 5

COMPONENTS DIAGRAM

Eyepiece

SD Card Slot

HDMI Port

Head

USB Port

AV Port

Zoom Knob

Camera Power Button

Indicator Lamp

Capture Button

Stand Arm

Upper Light Source

Focusing Knob

Lower Light Source

Light Adjustment Knob

Power Switch

Upper Light Source

Light Adjustment Knob

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 6

ASSEMBLY

The diagram below shows how to assemble the various components. The numbers indicate the order of

assembly.

When assembling the microscope, make sure that all parts are free of dust and dirt, and avoid scratching

any parts or touching glass surfaces.

Eyepieces

Power cord

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 7

OPERATION)

Setting Illumination (Fig. 3)

Turn the light adjustment knobs and as

shown on the base in Fig. 3: turn clockwise to

increase brightness; counterclockwise to

decrease brightness.

Adjusting the Rotation Tension of the

Focus Adjustment Knob (Fig. 4)

To adjust tension, hold both left and right focus

adjustment knobs with both hands, hold the left

knob (to prevent it from turning), and rotate the

right knob clockwise to increase (tighten) or

counterclockwise to decrease (loosen) the focus

knob tension.

After tension adjustment has been completed,

always rotate both adjustment knobs in the

same direction

Adjusting Diopter Ring (Fig. 5)

Set the diopter rings of both eyepieces to “0”

position. (Do this when users change, because

different users will have different diopter

settings.)

Place an easy-to-observe specimen on the gem

stand.

Rotate the zoom knob to the highest

magnification, then turn the focusing knob to

focus the specimen.

Rotate the zoom knob to the lowest

magnification, looking only into the left eyepiece,

adjust the diopter ring on left eyepiece to focus

the specimen. Then repeat procedure for the

right eyepiece.

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 8

Adjusting Interpupillary Distance (Fig. 6)

Different users have different interpupillary

distances (this distance is between the centers of

the pupils of each eye). When the operator

changes, it will be necessary to adjust the

interpupillary distance.

While looking through the eyepieces, hold the left

and right eyetubes of the viewing headand adjust

the eyetubes by opening or closing them until the

left and right fields of view coincide completely and

you are able to see a complete circle.

Installing or Removing the Reticle (Fig. 7)

Unscrew the reticle retaining ring from the

eyepiece (see Fig. 7).

NOTE: be sure to clean the reticle with a soft, lint

free cloth or cotton swab dampened with a lens

cleaning solution (available at camera stores –see

p. 3, Care & Maintenance).

Insert the clean reticle into the eyepiece , then

screw the reticle retaining ring back onto the

eyepiece.

To remove the reticle, unscrew the reticle retaining

ring from the eyepiece, carefully remove the reticle,

and store the reticle in lint-free paper. Screw the

reticle retaining ring back onto the eyepiece.

Connecting the Cables - HDMI, USB, AV (Fig. 8)

HDMI: insert the HDMI cable into the HDMI port on

the microscope, then connect other end into the

HDMI port on an HDMI display.

USB: insert the USB cable into the USB port on the

microscope, then connect other end to a USB port

on a computer. You can then view, copy or delete

images on the SD card (be sure SD card is

inserted).

AV: Insert the AV cable into the AV port on the

microscope, then connect the other end into an AV

port on an AV display.





NOTE: Live images may be viewed

on any 720p or greater monitor.

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 9

Power Supply, Indicator Lamp

& Capture Button (Fig. 8)

Insert the SD card into the SD slot on the

microscope until a beeping sound is heard.

To start the camera module, turn on the camera

by pressing the power button on the microscope

head for 1-2 seconds; the indicated lamp will

light up after the system sounds with a beep.

To capture an image, press the Capture button.

The captured image is stored on the SD card.

Replacing the Fuse (Fig. 9)

Before replacing the fuse, turn the power switch

to “O” (Off), and unplug the power cord from the

outlet and the microscope.

Pull out the fuse base from the fuse socket.

Remove the fuse from the fuse base and

replace with a new one. Reinstall the fuse base

into the fuse socket.

Plug the power cord into the base of the

microscope and then into a wall outlet. Turn the

power switch to “--” (On).

MICROSCOPE SPECIFICATIONS

Optical System

Greenough

Eyepieces

WF10x/20mm field of view; 50 - 75mm interpupillary distance

Viewing Angle

60º

Working Distance

95mm

Magnification

8x-35x

Focusing System

Large dual focusing knobs with coarse adjustment; focusing range: 90mm

Illumination

Maintenance-free, 5 watt LED transmitted and incident illuminators with intensity control;

100V –240V; bulb life approx. 25,000 hours

Dimensions

285 (L) x 355 (H) x 186 (D) mm

Warranty

5 year limited warranty for parts, labor and electronic components;

1 year warranty on LED bulbs and camera

DIGITAL SPECIFICATIONS

Camera

5 megapixel CMOS built-in camera system

Digital Output

USB 2.0 PC Compatible

HDMI Port

720p High Definition output for desktop or large HD display

Integrated Slot

SD (Secure Digital); 2GB SD card included

Recording

Camera record push button control for image capture

3078-HD ZOOM STEREO MICROSCOPE

ACCU-SCOPE® 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com 10

TROUBLESHOOTING

Under certain conditions, performance of this unit may be adversely affected by factors other than

defects. If a problem occurs, please review the following list and take remedial action as needed. If you

cannot solve the problem after checking the entire list, please contact your local dealer for assistance.

Trouble

Cause

Remedy

Double images

Interpupillary distance is not correct

Readjust it

Diopter adjustment is not correct

Readjust it

Dirt appears in the view field

Dirt on the specimen

Clean specimen

Dirt on the surfaces of eyepieces

Clean eyepieces

Dirt on surface of objective

Clean objective

Dirt on stage

Clean stage

Image is not clear

Dirt on the surface of objectives

Clear objectives

Image is not clear while focusing

Diopter adjustment is not correct

Readjust diopter

Focusing is not correct

Readjust it

The focusing knob is not smooth

The focusing knob is too tight

Loosen it to a suitable position

The image is obscure because of the

head slipping down during

observation

The focusing knob is too loose

Tighten it to a suitable position

A line appears when observing

through eyepiece or video device

Light path selection lever is not at

the correct position

Turn it to the correct position

Lamp does not work

Wrong setting of bulb

Set the bulb correctly

Bulb has burned out

Replace the bulb

Fuse has burned out

Replace the fuse

Dirt on the stage obstructed the

path of light

Clean the stage

Lamp burns out frequently

Voltage from power supply is too

high

Use a transformer to decrease

the voltage

The bulb is not standard

Use the recommended bulb

Fuse burns out frequently

Voltage from power supply is too

high

Use a transformer to decrease

the voltage

Light flickers

Bulb needs replacement

Replace bulb

The wires are not connected

correctly

Correctly connect the wires

Tabla de contenidos

Otros manuales de Microscopio de Accu-Scope

Accu-Scope

Accu-Scope 3000-LED series Manual de usuario

Accu-Scope

Accu-Scope 3052-GEM Manual de usuario

Accu-Scope

Accu-Scope 3019 Manual de usuario

Accu-Scope

Accu-Scope EXS-210 Manual de usuario

Accu-Scope

Accu-Scope EXC-400 Series Manual del propietario

Accu-Scope

Accu-Scope Excelis HD Manual de usuario

Accu-Scope

Accu-Scope 3025 Series Manual de usuario

Accu-Scope

Accu-Scope EXI-410 Series Manual de usuario

Accu-Scope

Accu-Scope EXI-310 Series Manual de usuario

Accu-Scope

Accu-Scope MT-40 Series Manual de usuario

Accu-Scope

Accu-Scope EXM-50 Manual del propietario

Accu-Scope

Accu-Scope EXC-500 Manual de usuario

Accu-Scope

Accu-Scope EXC-100 Series Manual de usuario

Accu-Scope

Accu-Scope 3065 Manual de usuario

Accu-Scope

Accu-Scope 3078-HDR Manual de usuario

Accu-Scope

Accu-Scope EXI-600 Manual de usuario

Accu-Scope

Accu-Scope EXI-410 Series Manual de usuario

Accu-Scope

Accu-Scope 3088F Manual de usuario

Accu-Scope

Accu-Scope EXM-150-MS Manual de usuario

Accu-Scope

Accu-Scope 3000-LED series Manual de usuario

Accu-Scope

Accu-Scope 3025-2 Manual del propietario

Accu-Scope

Accu-Scope 3075 SERIES Manual de usuario

Accu-Scope

Accu-Scope EXC-350-PH Manual de usuario

Accu-Scope

Accu-Scope 3050 Series Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario