Accu-Scope 3002 Manual de usuario

Table of Contents

Safety Notes………………………………………………….…. i

Care and Maintenance………………………………………... ii

1. Component Illustration ……………………………………… 1

2. Installation of Components ………………………………….. 2

3. Adjusting Components……………………………………….. 7

4. Operation……………………………………………………… 9

5. Technical Specifications …………………………………….. 12

6. Component List ………………………………………………13

7. Trouble Shooting Guide …………………………………….. 14

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from

dropping and being damaged.

2. Do not discard the molded Styrofoam container; the container should be retained should the

microscope ever requires reshipment.

3. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

Ensure the microscope is located on a smooth, level and firm surface.

4. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may

be damaged.

5. CAUTION: the lamp, lamp housing and adjacent parts will become very hot. Do not touch these

parts until they have completely cooled. Never attempt to handle a hot halogen bulb.

6. All electrical connectors (power cord) should be inserted into an electrical surge suppressor to

prevent damage due to voltage fluctuations.

7. For safety when replacing the halogen lamp or fuse, be sure the main switch is off (“O”), remove

the power cord, and replace the halogen bulb after the bulb and the lamp house has completely

cooled.

8. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage than indicated will cause severe damage to the microscope.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objectives or focusing

assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air stream

from an air bulb. If dirt remains on the optical surface, use a soft cloth or cotton swab dampened

with a lens cleaning solution (available at camera stores). All optical lenses should be swabbed

using a circular motion. A small amount of absorbent cotton wound on the end of a tapered stick

makes a useful tool for cleaning recessed optical surfaces. Avoid using an excessive amount of

solvents as this may cause problems with optical coatings or cemented optics or the flowing

solvent may pick up grease making cleaning more difficult. Oil immersion objectives should be

cleaned immediately after use by removing the oil with lens tissue or a clean, soft cloth.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when

not in use.

5. ACCU-SCOPE microscopes are precision instruments which require periodic servicing to

maintain proper performance and to compensate for normal wear. A regular schedule of

preventative maintenance by qualified personnel is highly recommended. Your authorized

ACCU-SCOPE distributor can arrange for this service.

bino

3002 BINOCULAR MICROSCOPE SERIES

Eyepiece

Binocular Viewing Head

Nosepiece

Objective

Body

①

②

2.1 Installation of Components

The diagram shows the numerical order to assemble the microscope. Inspect all optical surfaces for dust

and debris; clean if necessary. Do not use force to install any component; all components should be

installed without strain.

Body

Objectives

ÅBinocular Viewing Head

Eyepieces

④

③

Power Cord

2. Installation Procedure

Figure 1

Figure 3

Figure 2

Installation of the Binocular

Viewing Head (Figures 1 & 2)

Insert the binocular viewing head into

the head of the body; ensure that the

dovetail is completely seated into the

body; tighten the thumb screw. Do not

release the head from your hand grip

until you are sure the head is installed

securely.

Installation of the Eyepieces

(Figures 3 & 4)

Remove the protective caps from the

eyepiece tubes. Insert the eyepieces into

the eyepiece tubes.

Figure 4

Figure 6

Figure 5

Figure 7

Installing the Objectives (Figures 5 &6)

1: Adjust the coarse focus knob until the mechanical stage

is at its lowest position.

2. Install the 4x objective into the nosepiece. Then in a

clock-wise direction, rotate the nosepiece and install

each succeeding higher magnification objective.

Inspect the objectives frequently for dirt or oil; clean

if necessary.

Use the 10X objective to initially focus the image of

yourspecimen.

When changing the objective magnification, rotate the

objective nosepiece until you hear a “click” sound.

This ensures the objective is centered in the optical

light path.

Installing the Glass Filter (Figure 7)

1. Swing out the condenser holder①

2. Insert the filter into the holder; swing the holder in.

Installing the Power Cord

(Figures 8-9-10)

★Do not bend or crush the power cord. This could

cause the cord to become unusable or dangerous.

1. Before connecting the power cord, make

sure the switch ①is in the “off” (O)

position.

2 Insert the female end of electrical cord plug

②into the socket ③.

3: Insert the male end of the power cord ④

into a surge suppressor receptacle ⑤.

★The microscope is factory set for either

110volts or 220volts.

Replacing the fuse (Figure 9)

Disconnect the power cord; ensure the

switch ①is “off”. Using a flat edge

screwdriver, remove the fuse holder ⑥,

insert new fuse, then insert the fuse holder

securely ⑦.

Figure 8

Figure 9

Figure 10

Figure 11

Figure 12

Installing & Changing the Halogen

Bulb（Figures 11, 12 & 13）

NOTE: Use only 6volt 20watt halogen

lamp.

1: Pull out & remove the condenser set ①.

1. Insert halogen lamp ①into the lamp

socket. NOTE: Do not touch the glass on

the bulb with your bare fingers. Handle

by using a soft cloth or tissue.

2. Changing the lamp during usage.

Ensure the power switch is off. Allow

time for all parts and the lamp are cooled

before handling.

Insert the lamp carefully; be sure the

pins on the bulb are completely inserted

into the lamp socket.

Attach the condenser set.

Figure 13

Otros manuales para 3002

Tabla de contenidos

Otros manuales de Microscopio de Accu-Scope

Accu-Scope

Accu-Scope EXI-600 Manual de usuario

Accu-Scope

Accu-Scope 3055 Manual de usuario

Accu-Scope

Accu-Scope 3000-LED series Manual de usuario

Accu-Scope

Accu-Scope EXM-150-MS Manual de usuario

Accu-Scope

Accu-Scope EXS-210-24 Manual de usuario

Accu-Scope

Accu-Scope 3075 SERIES Manual de usuario

Accu-Scope

Accu-Scope 3000-LED-SPH Manual de usuario

Accu-Scope

Accu-Scope EXM-150 SERIES Manual de usuario

Accu-Scope

Accu-Scope 3019 Manual de usuario

Accu-Scope

Accu-Scope 3052-LED Manual de usuario

Accu-Scope

Accu-Scope 3078 Series Manual de usuario

Accu-Scope

Accu-Scope EXS-210 Manual de usuario

Accu-Scope

Accu-Scope 3078-HD Manual de usuario

Accu-Scope

Accu-Scope EXC-350-PH Manual de usuario

Accu-Scope

Accu-Scope EXC-120-PL Manual de usuario

Accu-Scope

Accu-Scope EXI-310 Series Manual de usuario

Accu-Scope

Accu-Scope 3025-LCD Manual de usuario

Accu-Scope

Accu-Scope Excelis HD Manual de usuario

Accu-Scope

Accu-Scope EXI-600 Manual de usuario

Accu-Scope

Accu-Scope 3012-LED Manual de usuario

Accu-Scope

Accu-Scope 3025 Series Manual de usuario

Accu-Scope

Accu-Scope 3002-CB Forensic Comparison Series Manual de usuario

Accu-Scope

Accu-Scope 3025 Series Manual de usuario

Accu-Scope

Accu-Scope 3075-GS Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario