3D Systems ProJet 6000 Manual de usuario

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 1of7

Purpose: To provide step-by-step work instructions for manually stirring the vat in the ProJet 6000 and

7000 printers.

Tools & Supplies Required:

•Nitrile gloves

•Safety goggles

•Lab coat

•Absorbent paper towels

•3/8” to 1/2” variable-speed drill (cord or cordless) which can operate to stir resin for at least 30

minutes.

•A propeller which has a long shaft stem and can be attached to the drill for mixing. The total length

of the propeller should not be longer than 6” (15cm).

Example propeller

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 2of7

•Open the machine door and remove the platform from the system (if it is in the system)

•Close the door. When alerted, select “Yes” to turn the power back on.

•Go to the “Advanced” screen, select “Elevator/Leveler,” and select “Home.”

•Wait for the elevator to move to the home position.

•Enter “-5” in the “Distance” box and select “Move Elevator.”

•Wait for the elevator to reach the bottom limit.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 3of7

•Go to the “Advanced” page, select “Print Applicator,” and select “Park.”

•Wait for the print applicator to move to the park position.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 4of7

•Go to the “Advanced” screen and select “Elevator/Leveler.”

•Select “Drain Print Tray.”

•Let the resin drain until the resin level in the print tray is about 2” below the rim.

•Install the propeller shaft to the drill.

•Ensure that you have the appropriate protective equipment on (gloves, googles, lab coat).

•Open the machine door.

•Remove any visible debris in the print tray.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 5of7

•Put the propeller at the stirring position. The stem should form a 45-60° angle with the

horizontal plane.

•The propeller should be submerged at the center of the print tray.

•Turn on the drill and slowly increase the rpm until it reaches the highest rpm without the

resin overflowing.

•Stir the resin for about 30 minutes.

•During the stirring procedure, debris may collect around the propeller or show up on the

resin surface. If this occurs, stop stirring and remove the debris.

•When you have finished stirring, remove the drill and place the drill and propeller in an

appropriate location, supporting them with absorbent paper towels to avoid spilling excess

resin on any surfaces.

Drill with propeller submerged in the

resin at the proper angle for stirring

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 6of7

•Close the machine door.

•When alerted, select “Yes” to turn the power back on.

•Go to the “Advanced” page, select “Elevator/Leveler,”and select

“Offload.”

•Wait for the elevator to move to the offload position.

•Open the machine door and install a clean platform.

•Close the machine door.

•When alerted, select “Yes” to turn the power back on.

•Select “Start.” Wait for the elevator to move to the start position.

•In the “Elevator/Leveler” menu, select “Level” to level the resin.

•When the resin level reading reaches roughly 31.000, select “Stop” to stop leveling.

•In the “Elevator/Leveler” menu, select “Home.”

•Wait for the elevator to home.

•Wait for large bubbles and micro-bubbles to disappear.

•The system is now ready for part building.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 7of7

END OF PROCEDURE

•To clean the drill and propeller, take them to a room away from the machine and wipe

down with isopropyl alcohol and paper towels.

•The drill components may then be post-cured in a Post Curing Apparatus (PCA) for at least

45 minutes on each side, making them safer for handling.

Otros manuales para ProJet 6000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de 3D Systems

3D Systems

3D Systems ZPRINTER 150 Manual de usuario

3D Systems

3D Systems Allevi 3 Manual de usuario

3D Systems

3D Systems ProJet 5000 Manual de usuario

3D Systems

3D Systems ProJet SLA 6000 Manual de usuario

3D Systems

3D Systems PROJET 3500 Guía de referencia

3D Systems

3D Systems 3D Sprint Manual de usuario

3D Systems

3D Systems Cube 3rd Generation Manual de usuario

3D Systems

3D Systems ProX 800 Manual de usuario

3D Systems

3D Systems ProJet 3500 Max Series Manual de usuario

3D Systems

3D Systems Duraform ProX PA Manual de usuario

3D Systems

3D Systems Cubify CUBEX Duo Manual de lista de piezas

3D Systems

3D Systems ProJet 2500 Manual de usuario

3D Systems

3D Systems CUBE Manual del operador

3D Systems

3D Systems DMP Flex 350 Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems projet mjp 2500 Manual de usuario

3D Systems

3D Systems Cubify CUBEX Duo Manual de usuario

3D Systems

3D Systems Figure 4 Standalone Manual de usuario

3D Systems

3D Systems ProJet 4500 Manual de usuario

3D Systems

3D Systems Viper Pro SLA iPro 8000 Manual de usuario

3D Systems

3D Systems wematter Gravity Manual de usuario

3D Systems

3D Systems CubeX Manual de usuario

3D Systems

3D Systems wematter Atmosphere Manual de usuario

3D Systems

3D Systems Cubify CUBEX Duo Instrucciones de funcionamiento y seguridad

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario