3D Systems Figure 4 Standalone Manual
Figure 4 Standalone®Setup
Please see the Figure 4 Standalone User Guide, found on the support.3dsystems.com/gure4standalone, for safe-
ty information and comprehensive operating instructions.
Save all foam and packing material for future use. Shipping without the original packing material may
cause damage to the printer.
1. Unbox and Stage Printer
1. Remove 4 packing clips around the bottom of the printer.
2. Lift outer box to remove. Ensure your ceiling clearance is at
least 2.6m (8.5 ft) to lift this box off.
3. Remove accessories box. Compare contents of box to list in
the Welcome Letter to ensure everything is included.
4. Remove documentation. Remove foam pieces and plastic
sleeve simultaneously (they are taped together).
5. If you are using the pedestal, proceed to
Section 2. If not, team-lift printer onto a
level surface and skip to Section 6.
6. Remove desiccant pack.
1
2. Unbox Pedestal
1. Cut box top open. Remove two pieces of packing foam from top of pedestal.
2. Remove plastic sleeve from the pedestal.
3. Grab pedestal with one hand by rectangular hole in middle and lift out of box.
4. Remove tape from all four casters.
5. Stage pedestal on a level oor and remove the blue tape from the door.
6. Open door and remove tape and cardboard spacer.
3. Place Printer on Pedestal
PINCH HAZARD: Keep
ngers/hands clear of
gap between printer and
pedestal.
Team-lift printer onto
pedestal, tting four rubber
printer feet into four holes
in top of pedestal. Ensure you install
printer in orientation shown, with
front of printer lining up with front of
pedestal.
34
5
2
6
12 3
45 6
Figure 4 Standalone®Setup
Please see the Figure 4 Standalone User Guide, found on the support.3dsystems.com/gure4standalone, for safe-
ty information and comprehensive operating instructions.
Save all foam and packing material for future use. Shipping without the original packing material may
cause damage to the printer.
CAUTION: You must secure
the printer to the pedestal
before use. Failure to do so
could cause the printer to tip
over in certain situations.
1. Open the pedestal door.
2. Install all ve thumb screws on
inside top of pedestal. Ensure they
are screwed in snugly.
3. Remove all remaining blue tape
from printer.
4. Secure Printer to Pedestal 6. Level Printer on Pedestal
6. Level Printer on Pedestal (continued)
1. Place the bubble level (included
with printer shipment) on printer
chassis.
2. The pedestal has four casters
with leveling feet. To adjust each
leveling foot:
a. Turn the orange thumb wheel
to the right to lower it.
b. Turn the orange thumb wheel
to the left to raise it.
3. You will now adjust the leveling feet.
a. Keep back-left leveling foot off the ground.
b. Lower front-right leveling foot until it touches the ground.
c. Lower front-left leveling foot until it touches the ground. Adjust foot up or down until bubble in level is roughly
centered in the circle left-to-right.
4. Lower the back-right leveling foot until it touches the ground. Adjust foot up or down until the bubble in the level is
roughly centered in the circle back-to-front.
5. Verify that the left-to-right level has not changed. Continue adjusting the front-left and/or back-right feet until bubble
is roughly centered in both directions.
6. Lower back-left foot until it touches the ground. Take care not to lower it too much, so as to throw the level off.
7. Push lightly on each corner of the machine to ensure it does not rock in any direction.
1. Remove thumb screws from lter
bracket. Remove lter bracket.
2. Slide carbon lter into place
3. Reinstall bracket with lter and
reinstall thumbscrews.
5. Install Carbon Filter
1
2
1
2
3
ab
c
4
Figure 4 Standalone®Setup
Please see the Figure 4 Standalone User Guide, found on the support.3dsystems.com/gure4standalone, for safe-
ty information and comprehensive operating instructions.
Save all foam and packing material for future use. Shipping without the original packing material may
cause damage to the printer.
7. Install Resin Tray
1. Open the printer lid and front
door.
2. Push in the tension-release button
(a) and lift the tension arm (b).
3. Install resin tray in chassis, concave
side up and with ll lines in the
back (see Initial Print Guide). Low-
er the tension arm and push down
on it until it locks into place.
1 2
3
a
b
8. Power Printer On 9. Install 3D Sprint
Ensure your computer can run
3D Sprint - See User Guide for
specs.
2
1
1. On a PC, go to support.3dsystems.
com/gure4standalone. Click In-
stall Software link.
2. Follow the instructions to down-
load/install 3D Sprint.
10. Add Printer
1. Open 3D Sprint. Click the Printer icon if the Printer window is not already
open.
2. Click Find Printer button to nd printer on your network. If this fails, enter
the printer’s IP address and press Enter. The IP address can be found on the
printer’s touch screen on the Settings tab (above, right).
3. Click the Figure 4 Standalone icon that the software just found.
4. Click Next.
1
2
3
4
You will need to make the printer’s IP address an exception on your
network’s rewall, if applicable. Both the printer and the PC running 3D
Sprint must be on the same network and connected to the internet.
11. Select Material
2
1
1. Click the icon for the resin you wish
to use.
2. Click the Next button.
1. Plug in power cable and Ethernet
cable.
2. Flip the power switch to the “I”
position to turn printer on.
3. The printer will search for rmware
updates. Tap Install on the touch
screen to install them.
802.11n WiFi bridge >300Mbps
may be connected to ethernet
port.
2
1
1
3
Figure 4 Standalone®Setup
Please see the Figure 4 Standalone User Guide, found on the support.3dsystems.com/gure4standalone, for safe-
ty information and comprehensive operating instructions.
Save all foam and packing material for future use. Shipping without the original packing material may
cause damage to the printer.
©2018 3D Systems, Inc. All rights reserved. P/N 42-D018 Rev. B
Other Useful Documents
See the 3D Sprint Help menu
for more information on
Print Modes.
12. Select Print Mode
1. Select 50 Micron for this test build
2. Click the Set button.
1
2
See the 3D Sprint Help menu
for more information on Build
Styles.
13. Select Build Style
1. Select Draft for this test build.
2. Click the Set button.
1
2
14. Initial Print Guide
Continue to the Initial Print Guide,
which is packed in with your printer.
This guide will show you how to print a
verication build.
Please visit support.3dsystems.com/gure4stand-
alone for up-to-date versions of the following docu-
ments:
Figure 4 Standalone User Guide - See full details
regarding safety, facility requirements, post-
processing instructions, and more for your printer.
SDS and User Guide - User Guides ship with each
material. These and SDSs are also available on
https://www.3dsystems.com/materials.
3D Sprint Online Help - Launch online help by press-
ing F1 or clicking the icon while in the software.
Otros manuales de Impresora 3D de 3D Systems
3D Systems
3D Systems ProJet 7000 Manual de usuario
3D Systems
3D Systems CubePro Manual de usuario
3D Systems
3D Systems SLA 750 Series Manual de usuario
3D Systems
3D Systems Cubify CUBEX Duo Manual de usuario
3D Systems
3D Systems ZPRINTER 650 Manual de usuario
3D Systems
3D Systems ZPRINTER 150 Manual de usuario
3D Systems
3D Systems ProJet 6000 Manual de usuario
3D Systems
3D Systems Cubify CUBEX Duo Instrucciones de funcionamiento y seguridad
3D Systems
3D Systems Geomagic Touch Manual de usuario
3D Systems
3D Systems CubePro Manual de usuario
3D Systems
3D Systems ProJet 4500 Manual de usuario
3D Systems
3D Systems wematter Gravity Manual de usuario
3D Systems
3D Systems wematter Atmosphere Manual de usuario
3D Systems
3D Systems ProJet MJP 5600 Manual de usuario
3D Systems
3D Systems CUBE Manual de usuario
3D Systems
3D Systems CubeX Instrucciones de montaje
3D Systems
3D Systems Viper Pro SLA Manual de usuario
3D Systems
3D Systems ProJet 1200 Manual de usuario
3D Systems
3D Systems ProJet 3500 Max Series Manual de usuario
3D Systems
3D Systems ProX SLS 6100 Manual de usuario
