3D Systems Cubify CUBEX Duo Manual de usuario

CUBEX

Measuring

Stepper motor

chip voltages

Contents

What you will need ..................................................................................................... 3

Removing the Jet Wipe .............................................................................................. 4

Removing the Case and floor panel. .......................................................................... 4

Voltage Measurement Locations................................................................................ 6

Reading the Voltages................................................................................................. 7

Re attaching the floor panel and case........................................................................ 8

What you will need

Multimeter

3mm hex driver

Small Screwdriver

Before beginning this process please ensure that all cartridges have been

removed from the machine.

Removing the Jet Wipe

Run the bed to the bottom of the machine using manual move.

Lift Jet wipe out of the machine

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

Voltage Measurement Locations

Depending which stepper motor chip voltage you want to read, you will need to

position your multimeter in different positions of the board. You will need to place a

small screwdriver with one end of the multimeter clipped onto it on the small screw

head labelled TP – and another end of the multimeter will need to be set to ground

on the board.

TP X will measure the voltage for the X axis.

TP Y will measure the voltage for the Y axis.

TP Z will measure the voltage for the Z axis.

TP E1, TP E2 and TP E3 will measure the voltage for print jets 1, 2 and 3.

TP Z

TP Y

TP X

Ground

Reading the Voltages

Plug the CubeX into mains power

Set the multimeter to read DC voltage.

Place the Red (positive) lead onto the desired TP screwhead.

TP E1

TP E2

TP E3

Hold the other end of the multimeter against the ground point.

The multimeter screen will give you your voltage reading.

TP X should read 1.3VDC

TP Y should read 1.6VDC

TP Z should read 1.3VDC

TP E1, E2 and E3 should read 1.1VDC

If your voltage is not correct use the small screwdriver to turn the screwhead in very

small increments measuring the voltage between each turn until it is correct.

Unplug your CubeX from mains power.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

You may now power up your CubeX.

Otros manuales para Cubify CUBEX Duo

Tabla de contenidos

Otros manuales de Impresora 3D de 3D Systems

3D Systems

3D Systems ProJet 1200 Manual de usuario

3D Systems

3D Systems ProJet 4500 Manual de usuario

3D Systems

3D Systems ProJet 7000 Manual de usuario

3D Systems

3D Systems ZPRINTER 650 Manual de usuario

3D Systems

3D Systems CubePro Manual de usuario

3D Systems

3D Systems ProJet 4500 Manual de usuario

3D Systems

3D Systems ProX 500 Manual de usuario

3D Systems

3D Systems ProX SLS 6100 Manual de usuario

3D Systems

3D Systems ZPRINTER 150 Manual de usuario

3D Systems

3D Systems DMP Flex 350 Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems CubePro Instrucciones de montaje

3D Systems

3D Systems PROJET 3500 Guía de referencia

3D Systems

3D Systems CubeX Manual de usuario

3D Systems

3D Systems ZPRINTER 150 Manual de usuario

3D Systems

3D Systems Duraform ProX PA Manual de usuario

3D Systems

3D Systems ProX SLS 6100 Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems FabPro 1000 Manual

3D Systems

3D Systems CubePro Manual de usuario

3D Systems

3D Systems ProJet 1200 Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems Geomagic Touch Manual de usuario

3D Systems

3D Systems Cube 3rd Generation Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario