ZyXEL Communications GS1100-8HP Manual de usuario

Quick Start Guide

www.zyxel.com

GS1100 Series

Unmanaged Gigabit Ethernet Switch

Version 1.00

Edition 5, 09/2015

User’s Guide

GS1100 Series User’s Guide

IMPORTANT!

READ CAREFULLY BEFORE USE.

KEEP THIS GUIDE FOR FUTURE REFERENCE.

Screenshots and graphics in this book may differ slightly from your product due to differences in

your product firmware or your computer operating system. Every effort has been made to ensure

that the information in this manual is accurate.

• MoreInformation

Go to support.zyxel.com to find other information on the Switch.

Table of Contents

GS1100 Series User’s Guide

Table of Contents

Table of Contents .................................................................................................................................3

Chapter 1

Getting to Know Your Switch...............................................................................................................4

1.1 Introduction .........................................................................................................................................4

1.2 Features ..............................................................................................................................................5

1.3 Applications .........................................................................................................................................6

1.3.1 Standalone Workgroup ..............................................................................................................6

1.3.2 Bridging .....................................................................................................................................6

1.4 Power Over Ethernet (PoE) ................................................................................................................7

Chapter 2

Hardware Description and Connection ..............................................................................................8

2.1 Rear Panel .......................................................................................................................................8

2.1.1 Rear Panel Power Connection ..................................................................................................8

2.2 Front Panel ..........................................................................................................................................9

2.2.1 RJ-45 Auto-negotiating Ports ....................................................................................................9

2.2.2 IEEE 802.3az EEE ....................................................................................................................9

2.2.3 SFP Slots (GS1100-24 and GS1100-10HP) ..............................................................................9

2.2.4 Front Panel Connections ......................................................................................................... 11

2.2.5 Front Panel LEDs .................................................................................................................... 11

2.3 Hardware Installation ........................................................................................................................14

2.3.1 Wall Mounting ..........................................................................................................................14

2.3.2 Rack Mounting .........................................................................................................................15

2.3.3 Mounting the Switch on a Rack ...............................................................................................16

Chapter 3

Troubleshooting..................................................................................................................................18

3.1 Improper Network Cabling and Topology ..........................................................................................19

Appendix A Legal Information............................................................................................................20

Index ....................................................................................................................................................29

GS1100 Series User’s Guide

CHAPTER 1

Getting to Know Your Switch

1.1 Introduction

This chapter describes the key features, benefits and applications of your Switch.

This User’s Guide covers the following models: GS1100-8HP, GS1100-16, GS1100-24, GS1100-24E

and GS1100-10HP. The Switch is a 10/100/1000 Mbps multi-port switch that can be used to build

high-performance switched workgroup networks. The Switch is a store-and-forward device that

offers low latency for high-speed networking. The Switch is fanless and designed for workgroups,

departments or backbone computing environments for small businesses.

The GS1100-8HP has four GbE PoE ports that can supply power to the connected PoE powered

devices.

The GS1100-10HP has eight GbE PoE ports that can supply power to the connected PoE powered

devices.

The GS1100-24 and GS1100-10HP have two SFP slots for uplink connection. Use SFP transceivers

in these slots for 100Mbps or 1Gbps connections to backbone Ethernet switches.

The Switch has a built-in algorithm that automatically assigns priority to received packets. It can

operate in low power idle mode in compliance with IEEE 802.3az Energy Efficient Ethernet (EEE).

Table 1 GS1100 Series Comparison Table

PORT/SWITCH DETAILS GS1100-8HP GS1100-16 GS1100-24 GS1100-24E GS1100-10HP

10/100/1000Base-T Ethernet ports

8 162424 8

100/1000Base-X SFP slots 22

802.3AT PoE ports 4 8

OnephysicalIEEE802.3azON/OFFbutton 11111

One power ON/OFF switch 1 1 1 1

Chapter 1 Getting to Know Your Switch

GS1100 Series User’s Guide

Figure 1 Front Panel

1.2 Features

The following are the essential features of the Switch.

• Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards.

• Auto-negotiating 10/100/1000 Mbps Gigabit Ethernet(GbE) RJ-45 ports.

• Auto-sensing crossover for all 10/100/1000 Mbps Gigabit Ethernet (GbE) RJ-45 ports.

• Supports N-Way protocol for speed (10/100/1000 Mbps) and duplex mode (Half/Full) auto-

detection.

• Supports store-and-forward switching.

• Supports automatic address learning.

• Supports IEEE 802.3az EEE

• Supports IEEE 802.3af and IEEE 802.3at PoE standards (GS1100-8HP and GS1100-10HP)

• Full wire speed forwarding rate.

• Supports 802.1p CoS.

• Embedded 8K MAC address table providing 8000 MAC addresses entries.

GS1100-8HP

GS1100-16

GS1100-24

GS1100-24E

GS1100-10HP

Chapter 1 Getting to Know Your Switch

GS1100 Series User’s Guide

1.3 Applications

This section provides two network topology examples in which the Switch is used.

1.3.1 Standalone Workgroup

In this application, the Switch is an ideal solution for small networks where rapid growth can be

expected in the near future.

The Switch can be used standalone for a group of heavy traffic users. You can connect computers

directly to the Switch’s port or connect other switches to the Switch.

In this example, all computers can share high-speed applications on the server. To expand the

network, simply add more networking devices such as switches, routers, computers, print servers

etc.

Figure 2 Standalone Workgroup Example

1.3.2 Bridging

With its large address table and high performance, the Switch is an ideal solution for department

networks to connect to the corporate backbone or for connecting network segments.

The following figure depicts a typical segment bridge application of the Switch in an enterprise

environment. The two networks (R&D and Sales), the standalone server and the computers can all

communicate with each other and share all network resources.

Figure 3 Bridging Example

Chapter 1 Getting to Know Your Switch

GS1100 Series User’s Guide

1.4 Power Over Ethernet (PoE)

The PoE function is available for GS1100-8HP and GS1100-10HP.

Ports 1 to 4 on the GS1100-8HP are IEEE 802.3at High Power over Ethernet (PoE) compliant and

can supply power of up to 30W per Ethernet port and up to the total PoE power budget per Switch.

Ports 1 to 8 on the GS1100-10HP support both the IEEE 802.3af Power over Ethernet and IEEE

802.3at High Power over Ethernet standards. The ports supply power of up to 30W per Ethernet

port and up to the total PoE power budget per Switch.

The Switch is Power Sourcing Equipment (PSE) because it provides a source of power via its

Ethernet ports. A powered device (PD) is a device such as an access point or an IP phone, that

supports PoE (Power over Ethernet) so that it can receive power from another device through a 10/

100/1000 Mbps Ethernet port.

In the figure below, the IP camera and IP phone get their power directly from the Switch. Aside

from minimizing the need for cables and wires, PoE removes the hassle of trying to find a nearby

electric outlet to power up devices.

Figure 4 Powered Device Examples

GS1100 Series User’s Guide

CHAPTER 2

Hardware Description and Connection

2.1 Rear Panel

The power receptacle is located on the rear panel of the Switch. Refer to the power supply

requirements on the panel.

Figure 5 Rear Panel

2.1.1 Rear Panel Power Connection

Connect one end of the supplied power cord or power adaptor to the power receptacle on the back

of the Switch and the other end to the appropriate power source.

For the GS1100-8HP, GS1100-16, GS1100-24E and GS1100-10HP, use the POWER ON/ OFF

switch to have the Switch power on or off.

GS1100-16

GS1100-24

GS1100-8HP

GS1100-24E

GS1100-10HP

Chapter 2 Hardware Description and Connection

GS1100 Series User’s Guide

2.2 Front Panel

The front panel of the Switch includes the auto-negotiating 10 Base-T/100 Base-TX/1000 Base-T

RJ-45 ports and the LEDs.

The GS1100-24 and GS1100-10HP have two SFP slots. Refer to Section 2.2.3 on page 9 for more

information.

2.2.1 RJ-45 Auto-negotiating Ports

The 10 Base-T/100 Base-TX/1000 Base-T RJ-45 ports are auto-negotiating and auto-crossover.

An auto-negotiating port can detect and adjust to the optimum Ethernet speed (10/100/1000

Mpbs) and duplex mode (full duplex or half duplex) of the connected device.

An auto-crossover (auto-MDI/MDI-X) port automatically works with a straight-through or crossover

Ethernet cable.

2.2.2 IEEE 802.3az EEE

The Switch supports the IEEE 802.3az EEE (Energy Efficient Ethernet) standard to help reduce

power consumption. This allows the Switch to go into power saving mode and switch off part of

receive and transmit circuitry when it is not transmitting or receiving data through an Ethernet

connection.

An EEE-enabled device initiates Low Power Idle (LPI) signals to negotiate and wake up the remote

device when there is data to be transmitted. To use EEE, both devices should be EEE compliant.

EEE is configured on a per-system basis in the Switch. If one of the networking devices that

connect to the Switch doesn't support EEE, EEE may not work in the Switch to save power.

Press in the I EEE 802.3az EEE ON/ OFF button on the front panel to turn on the EEE feature.

Disable it if you don't want the network performance to be impacted due to the latency from the

additional time required for the sleep and wake transition or if the remote side doesn't support it.

2.2.3 SFP Slots (GS1100-24 and GS1100-10HP)

These are slots for Small Form-factor Pluggable (SFP) transceivers. A transceiver is a single unit

that houses a transmitter and a receiver. The Switch does not come with transceivers. You must use

transceivers that comply with the Small Form-factor Pluggable (SFP) Transceiver MultiSource

Agreement (MSA). See the SFF committee’s INF-8074i specification Rev 1.0 for details.

You can change transceivers while the Switch is operating. You can use different transceivers to

connect to Ethernet switches with different types of fiber-optic or even copper cable connectors.

To avoid possible eye injury, do not look into an operating fiber-optic

module’s connectors.

• Type: SFP connection interface

• Connection speed: 100 Megabit per second(Mbps) or 1 Gigabit per second (Gbps)

Chapter 2 Hardware Description and Connection

GS1100 Series User’s Guide

2.2.3.1 Transceiver Installation

Use the following steps to install a SFP module.

1Insert the transceiver into the slot with the exposed section of PCB board facing down.

2Press the transceiver firmly until it clicks into place.

3The Switch automatically detects the installed transceiver. Check the LEDs to verify that it is

functioning properly.

4Close the transceiver’s latch (latch styles vary).

5Connect the fiber optic cables to the transceiver.

Figure 6 Transceiver Installation Example

Figure 7 Connecting the Fiber Optic Cables

2.2.3.2 Transceiver Removal

Use the following steps to remove a SFP module.

1Remove the fiber optic cables from the transceiver.

2Open the transceiver’s latch (latch styles vary).

3Pull the transceiver out of the slot.

Figure 8 Removing the Fiber Optic Cables

Otros manuales para GS1100-8HP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de ZyXEL Communications

ZyXEL Communications

ZyXEL Communications ZyWALL 110 Series Manual

ZyXEL Communications

ZyXEL Communications P-335WT Manual de usuario

ZyXEL Communications

ZyXEL Communications PRESTIGE 334 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660RU-T1 v3s Manual de usuario

ZyXEL Communications

ZyXEL Communications Prestige 2602HWL-D3A Instrucciones de instalación

ZyXEL Communications

ZyXEL Communications DX5401-BO Manual de usuario

ZyXEL Communications

ZyXEL Communications P-2812HNU-51c Manual de usuario

ZyXEL Communications

ZyXEL Communications 660H/HW(-I) Manual de usuario

ZyXEL Communications

ZyXEL Communications VMG5304 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications NBG-419N v2 Manual de usuario

ZyXEL Communications

ZyXEL Communications LTE7461-M602 Manual de usuario

ZyXEL Communications

ZyXEL Communications P8802T Manual de usuario

ZyXEL Communications

ZyXEL Communications LTE3311 series Manual de usuario

ZyXEL Communications

ZyXEL Communications 650 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-791R V2 Manual de usuario

ZyXEL Communications

ZyXEL Communications Dimension GS-2024 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-334WT Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660R-T3 V2 Manual de instrucciones

ZyXEL Communications

ZyXEL Communications P-660 series Manual

ZyXEL Communications

ZyXEL Communications P-660RU-T1 v3 Manual de usuario

ZyXEL Communications

ZyXEL Communications Prestige 623R-T Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA5256 Manual de usuario

ZyXEL Communications

ZyXEL Communications NBG318S Series Manual de usuario

ZyXEL Communications

ZyXEL Communications Dimension ES-4024 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad