YASKAWA DS031 Manual de usuario

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 1 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Introduction

The remote digital operator kit allows a digital operator to be mounted up to 3 meters from the GPD305/J7. The

kit includes:

1. One remote operator interface attachment

2. One gasket

3. One Digital Operator membrane cover

4. Four screws & nuts

5. Eight rubber washers

6. One RS-232 remote operator interface

7. One cable either 1 meter (DS031) or 3 meter (DS033) in length.

Hardware Installation

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR DEATH. LOCK ALL POWER

SOURCES DRIVE IN “OFF” POSITION.

1. Disconnect all electrical power to Drive.

2. Verify power has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, and L3).

3. Wait for the DC bus capacitors to completely discharge.

4. Remove contents from package. Verify that the above mentioned parts are included:

5. install the RS-232 remote interface. First, remove the screw on the front cover of the drive. Next, remove the

small square cover located above the control terminals to access CN1. Install the RS-232 remote interface by

positioning the interface directly above the CN2 connector. Press down on interface until all three tabs snap

into place.

6. Re-attach the front cover and tighten the screw down.

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 2 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Flush Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 1.1

Figure 1.1 (Dimensions in Inches, not actual size)

2. Install the Remote Operator on the front side of the panel. Use four stainless screws and four rubber

washers (one rubber washer per screw). See Figure 1.2

FIGURE 1.2

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 3 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Surface Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 2.1

Figure 2.1

(Dimensions in Inches, not actual size)

2. Apply the gasket to the front side of the digital operator. Install the remote operator from the rear side of panel.

Insert the screws through the front side of the panel and then mount the washers and nuts to the rear side of the

panel. Tighten screws gradually from the front side of panel. Refer to figure 2.2 for further installation directions.

3. Connect one end of the cable to the CN1 connector on

the drive and the other end of the cable to the RJ-45

receptacle on the back of the Digital Operator.

This completes the installation process.

Figure 2.1 Remote Operator Installation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de YASKAWA

YASKAWA

YASKAWA MOTOMAN Series Manual de usuario

YASKAWA

YASKAWA SI-EP3 Manual de usuario

YASKAWA

YASKAWA MOTOMAN DX100 Manual de usuario

YASKAWA

YASKAWA Varispeed G7 Manual de usuario

YASKAWA

YASKAWA MP2000iec Guía del administrador

YASKAWA

YASKAWA A1000 Series Manual de usuario

YASKAWA

YASKAWA MP3300iec Manual de usuario

YASKAWA

YASKAWA VU*B****AA*-134 Series Manual de usuario

YASKAWA

YASKAWA SI-EP3 Manual de usuario

YASKAWA

YASKAWA PROFINET V1000 Manual de usuario

YASKAWA

YASKAWA Motoman DX200 Manual de usuario

YASKAWA

YASKAWA Sigma-7Siec Manual de usuario

YASKAWA

YASKAWA SI-M3/V Manual de usuario

YASKAWA

YASKAWA 050-1BA00 Manual de usuario

YASKAWA

YASKAWA PROFIBUS-DP SI-P3 Manual de usuario

YASKAWA

YASKAWA MP2200 Manual de usuario

YASKAWA

YASKAWA PROFIBUS-DP 1000 Series Manual de usuario

YASKAWA

YASKAWA L1000A Series Manual de usuario

YASKAWA

YASKAWA MP3300 series Manual de usuario

YASKAWA

YASKAWA MP3100 Series Manual de usuario

YASKAWA

YASKAWA motoman NX100 Manual de usuario

YASKAWA

YASKAWA SI-ES3 Manual de usuario

YASKAWA

YASKAWA PROFINET V1000 Manual de usuario

YASKAWA

YASKAWA YRC1000 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario