Yamaha 02R96 Version 2 Manual

02R96 V2.2 Supplementary Manual

The 02R96 System Software Version 2.20 features the following changes and additions (including the changes made

up to Version 2.11).

Changes and additions in Version 2.20

❏

More Add-On Effects Packages available (pages 155 and 158)

The following Add-On Effects Packages are now available:

•

AE041

Surround Post Package

•

AE051

Vintage Stomp Package

Due to this addition, effect memories #53 through 67 in the Effects library are now designated as preset effects pro-

grams. These preset programs are dedicated to Add-On Effects. The numbers of effects programs that do not have

Add-On Effects installed are grayed out and cannot be used. The following effects programs in the Effects library

have been dedicated to the new Add-On Effects Packages.

Please refer to the following Yamaha website for the latest information on the Add-On Effects Packages:

http://www.yamahaproaudio.com

❏

Additional trigger sources in the GPI OUTPUT section (pages 225 and 254)

The following parameters have been added as the trigger signal source in the GPI OUTPUT section.

xxx ON TALLY:

The trigger signal is active only while the corresponding channel is turned ON.

The following parameters have been added in the OUTPUT list of the “GPI Trigger Source & Target List” on

page

254.

❏

About the 02R96 Editor version

If you use the 02R96 Editor (Studio Manager) to control the 02R96, update the 02R96 Editor to version 2.1.2 or

higher (Studio Manager version 2.1 or higher).

If your Studio Manager CD-ROM version is not X5401

, download the latest version from the following Yamaha

website:

http://www.yamahaproaudio.com

No. Preset name Type

62 Room ER ROOM ER

63 Auto Doppler AUTO DOPPLER

64 Field Rotation FLD ROTATION

65 Max100 MAX100

66 Vintage Phaser VNTG PHASER

67 Dual Phaser DUAL PHASER

# Source

254 CH1 ON TALLY

309 CH56 ON TALLY

310 BUS1 ON TALLY

317 BUS8 ON TALLY

318 AUX1 ON TALLY

325 AUX8 ON TALLY

326 ST ON TALLY

Changes in V2.11

❏

Y96K card and MY16-mLAN card support (pages 59 and 299)

The Waves Y96K Plug-in DSP card (supported by Version 2.10) and the MY16-mLAN interface card are now sup-

ported. Also, in accordance with the mLAN MIDI speciﬁcations, multiple MIDI ports on SLOT 1 have been

changed to a single port. (Now you do not need to select Ports 1-8.)

Please refer to the following website for the latest information on compatible cards, and on the number of cards

that can be installed in combination with other cards.

http://www.yamahaproaudio.com

Changes in V2.10

❏

MIX C-R SOURCES parameter added to

Control Room Monitor (page 137)

A “MIX C-R SOURCES” parameter has been added in the

CONTROL ROOM SETUP page. In V2.0, you could

choose one item from 2TR D1, D2, D3, A1, or A2 as a

monitor source, plus other sources (STEREO, ASSIGN1,

or ASSIGN2). In V2.1, you can turn the MIX C-R

SOURCES parameter off to disable this simultaneous

selection.

❏

MIX MONITOR SOURCES parameter

added to Surround Monitor (page 138)

A “MIX MONITOR SOURCES” parameter has been

added to the SURROUND MONITOR page. In V2.0, you

could simultaneously choose a BUS and SLOT as the

monitor source, but in V2.1 you can turn this parameter

off to disable this simultaneous selection.

❏

THX presets added to Surround Monitor (page 139-141)

Presets for the THX pm3 monitor system have been added to the bass management settings for surround monitor-

ing. Several supplements have also been added regarding the surround monitor settings, so please replace the cor-

responding pages with the following.

Conﬁguring Surround Monitoring

Surround monitoring, including speaker setup, monitor matrix, Bass Management, and mon-

itor alignment, is conﬁgured on the Surround Monitor Setup page.

1 Use the MONITOR [DISPLAY] button to locate the Surround Monitor Setup

page.

2Use the cursor buttons to select the parameters, and use the Parameter wheel,

INC/DEC buttons, and [ENTER] button to set them.

SPEAKER SETUP:

These parameters are for setting the volume balance of the surround mon-

itor speakers. Select the OSC (Oscillator) parameter and choose from PINK NOISE, 500-2K

(pink noise through a 500 Hz to 2 kHz BPF), 1K (1 kHz sinewave), or 50 Hz (50 Hz sinewave).

Use the ON/OFF button to turn the Oscillator on and off. When on, the Oscillator outputs a

signal at –20 dB to the Surround Channels whose icons are highlighted. You can turn on and

off Oscillator output for speakers individually. Speaker icons can be selected by using the cursor

buttons. The signal phase of the LFE Channel can be reversed by using the SW phase button.

When ROTATE is on, the Oscillator signal is output by each speaker in turn in a clockwise

direction (3 second signal, 2 second pause).

SURR. MODE:

This indicates the currently selected Surround mode, which is set on the Sur-

round Mode page (see page 85).

MONITOR MATRIX:

This is used to select the Surround Monitor Matrix. In 6.1 Surround

mode, you can select 6.1, 5.1, 3-1, or ST. In 5.1 Surround mode, you can select 5.1, 3-1, or ST.

In 3-1 Surround mode, you can select 3-1 or ST.

When a down mix Monitor Matrix is selected, you can attenuate signals by using the ATT

parameters.

You can use the Surround Monitor settings in Stereo mode, but Monitor Matrix is ﬁxed to ST.

Note:

If you had been monitoring with the surround mode set to 6.1 and the monitor matrix mode

set to 6.1 on 02R96 units with system software earlier than V2.1, the playback may not always be

correct on V2.1.

Note:

If you choose monitor matrix mode = 3-1, you must set the following three attenuation

amounts to the same value.

• ATT1 for surround mode 3-1

• ATT4 for surround mode 5.1

• ATT5 for surround mode 6.1

These ATT values are not attenuators for down-mixing; rather, they are used as monitor adjust-

ment attenuators for lowering the playback volume of the Ls, Rs, Ls2, and Rs2 speakers.

The following screen shows an example in 6.1 Surround mode and 3-1 Monitor Matrix mode.

•BASS MANAGEMENT

You can set the ﬁlter and attenuator settings for each Surround Monitor Channel using eight

preset Bass Management modes. The following presets are available:

ATT1: Adjusts the level difference between LR and LsRs.

ATT2: Adjusts the level difference between C and Bs.

AMP: Corrects the LFE channel level.

HPF1–3: Cut the low range so that the speakers’ supporting frequency ranges will not interfere with the sub-

woofer signals.

HPF1–2: Cut the high range so that the subwoofer’s supporting frequency ranges will not interfere with other

speakers’ signals.

You can set the Bass Management parameters in the following ranges:

The HPF 1, 2, 3, and LPF 1 & 2 values indicate a cut-off frequency and a filter response. For example, “80-12”

means a cutoff frequency of 80 Hz and a filter response of –12 dB/octave.

“L” means Linkwitz filter. Other filters are Butterworth.

Presets Parameters

No. Title HPF 1, 2, 3 LPF1 LPF2 ATT 1 & 2 AMP

DVD LFE80Hz 80–12 80–24 80–24 0 10

DVD LFE120Hz 80–12 120–42 80–24 0 10

Movie LFE80Hz 80–12 80–24 80–24 –3 10

Movie LFE120Hz 80–12 120–42 80–24 –3 10

Bypass THRU THRU MUTE 0 0

THXD

THX DVD 80-12 120-42 80-24L 0 10

THXF

THX Movie 80-12 120-42 80-24L –3 10

THXM

THX Music 80-12 120-42 80-24L 0 10

Note:

•If you select preset THXD or THXF, you cannot change the parameters.

•If you select preset THXM, you can switch AMP between 10 dB and 0 dB. However, you cannot

change other parameters.

Parameters Range

HPF 1, 2, 3

THRU, 80-12, 80-12L, 80-24, 80-24L

LPF1

THRU, 80-24, 80-24L, 120-42

LPF2

THRU, 80-24, 80-24L, MUTE

ATT 1 & 2

0 to –12 dB (1 dB steps)

AMP

0 to +12 dB (1 dB steps)

About the Presets

(1)

DVD LFE80Hz

This is a preset optimized for DVD-Video production. The LFE playback bandwidth is set up

to 80 Hz. When using this preset, we recommend that you use an external device to apply an

LPF (fc=80 Hz, –24 dB/oct) to the LFE master source.

To monitor audio on DVD-Audio or SACD discs, change the LFE level (AMP) and LPF (LPF1)

to 0 dB and THRU, respectively, if necessary.

The LFE output gain on some DVD players and decoders may already be set to +10 dB. To

monitor the output from such devices, change the LFE level (AMP) to 0 dB.

(2)

DVD LFE120Hz

This is also a preset optimized for DVD-Video production. This preset is the same as preset (1)

mentioned above, except that the LFE playback bandwidth is set up to 120 Hz. Use this preset

to monitor standard LFE signals recorded on DVD-Video discs that include the high-end fre-

quency ranges (120 Hz).

(3)

Movie LFE80Hz

This preset is the same as preset (1) mentioned above, except that the output level of surround

channels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for

movie production.

When using this preset, we recommend that you use an external device to apply an LPF

(fc=80 Hz, –24 dB/oct) to the LFE master source.

(4)

Movie LFE120Hz

This preset is the same as preset (2) mentioned above, except that the output level of surround

channels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for

movie production.

(5)

Bypass

Use this preset not only for bass management but to bypass all parameters, such as the LFE level

& LPF, surround channel level, etc.

To disable only the bass management, select another preset, then turn off the BASS MANAGE-

MENT ON/OFF button.

■

THX Presets:

The following presets have been approved by THX™ Ltd. for use in THX pm3™ Certiﬁed Stu-

dios*. They are designed to provide dedicated parameters for the proper playback of multi-

channel audio content in bass managed systems and to be compatible with subwoofer-satellite

type consumer systems.

*Use of a THX preset does not permit a studio to use the designation - THX pm3 Certiﬁed Studio.

The THX pm3 Studio Certiﬁcation Program uses performance and design speciﬁcations to create

calibrated environments for optimum sound and picture presentation. For more information,

visit the THX website at http://www.thx.com

[THXD]

THX DVD

This preset is conﬁgured for DVD-Video production. Use this preset when mixing and/or

monitoring audio content not from a theatrical ﬁlm source. The parameters cannot be

changed.

[THXF]

THX Film

This preset is conﬁgured for Film pre-production. Use this preset when mixing and/or moni-

toring theatrical ﬁlm-based content (such as a pre-mix for ﬁlm). The parameters cannot be

changed.

[THXM]

THX Music

This preset is conﬁgured for DVD-Music production. Use this preset when mixing and/or

monitoring multi-channel music content (including DVD-Audio and SACD). Only one

parameter can be changed. The LFE gain (AMP) can be set to +10dB (default) or 0dB. Select

the level that complies with the standards of the target media. Please note: The LFE output gain

on some DVD players, receivers, and/or decoders may already be set to +10dB. Select the 0dB

setting only if the destination environment (home theatre, etc.) has the LFE gain set to 0dB.

Otherwise, use the default setting.

•MONITOR ALIGNMENT ATT & DLY ON/OFF

These buttons are used to turn on and off the Monitor Align-

ment Attenuator and Delay parameters of all Surround speak-

ers. The MONITOR ALIGNMENT diagram and Surround

Channel Attenuator and Delay parameters, which are dis-

played when either of these buttons are selected, allow you to

align the surround monitor speakers by attenuating and

delaying Surround Channels as necessary. The Attenuator

parameters can be set –

∞

, –12 dB to +12 dB in 0.1 dB steps. The Delay parameters can be set from

0 to 30 msec in 0.02 msec steps.

Note:

•Please note that the above settings apply only to the signals being monitored. They do not

affect the normal bus outputs.

•If you're monitoring in surround mode 6.1 and monitor matrix mode 6.1, you'll need to

make the above settings separately from when in other modes.

Tip:

The settings you make here can be stored in the surround monitor library.

Memo

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Otros manuales para 02R96 Version 2

Tabla de contenidos

Otros manuales de Software de Yamaha

Yamaha

Yamaha Add-On Effects Manual de usuario

Yamaha

Yamaha Studio Manager v.2 Manual de usuario

Yamaha

Yamaha DME-N Manual de usuario

Yamaha

Yamaha A3000 Manual de usuario

Yamaha

Yamaha File Utility Manual de usuario

Yamaha

Yamaha M7CL StageMix V1.5 Manual de usuario

Yamaha

Yamaha PM5D Manual de usuario

Yamaha

Yamaha QY100 Data Filer Manual de usuario

Yamaha

Yamaha S90 Manual de usuario

Yamaha

Yamaha CVP-403PE Manual de usuario

Yamaha

Yamaha EZ-220 Page Turner Manual de usuario

Yamaha

Yamaha VL Manual de usuario

Yamaha

Yamaha M7CL-32 Manual de usuario

Yamaha

Yamaha FIRESTATION MLAN PATCHBAY Manual de usuario

Yamaha

Yamaha Extension Manual de usuario

Yamaha

Yamaha disklavier MX-100A Manual de usuario

Yamaha

Yamaha DME-N Manual de usuario

Yamaha

Yamaha QS1-MC Manual de usuario

Yamaha

Yamaha mLAN Driver Manual de usuario

Yamaha

Yamaha MOTIF6 Voice Editor Manual de usuario

Yamaha

Yamaha DSP5D Editor Manual de usuario

Yamaha

Yamaha S70 XS Manual de usuario

Yamaha

Yamaha MOTIF RACK ES Manual

Yamaha

Yamaha A4000 Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario