Yakima FullBack Manual de usuario
BOTTOM
BOTTOM
PURCHASE
SEPARATELY:
TubeTop
Required for bikes with
step-through/Ladies
frames or bikes with
slanted top tubes.
Part #8002531
1035059C-1/42
FullBackTM
CONTENTS
9X
1X
1X
1X
2X 3X
6X
1X
1X
1X
1X
1X
PURCHASE
SEPARATELY:
TubeTopTM
Required for bikes with step-
through/Ladies frames or
bikes with slanted top tubes.
Part #8002531
FullBack (2 Bike)
35 lbs / 15.9 kg max per bike.
70 lbs / 31.75 kg total.
FullBack (3 Bike)
30 lbs / 13.6 kg max per bike.
90 lbs / 40.8 kg total.
3
1035059C-2/42
12
INSTALLATION
HUB SETTING
Clean the vehicle
FIT NOTES
HUB SETTING
•Rotate the center dial toward the
unlock icon and raise the upper
frame arm.
•Set its position to the HUB SETTING you
determined in step 1.
•Ensure that the center dial returns to
the aligned position.
•Ensure that the upper frame arm is
locked into the correct position.
OPTIONAL Install trunk security
strap.
Open trunk or hatch.
Insert anchor end of
trunk security strap
through opening
between trunk or hatch
and the vehicle. Be sure
strap is between the
hinges of trunk or hatch.
Close the trunk or hatch.
Wicking of
moisture
into the
vehicle may
occur in wet
conditions.
Thread strap end of trunk security strap
around frame, and insert anchor end of trunk
security strap through loop as shown.
Set the hub
4
5
1035059C-3/42
Upper Frame:
•The position is relative to the lower frame and will depend
on vehicle shape.
•Any contact with a spoiler is not acceptable
Lower Frame:
•LOWER SUPPORT FRAME LOCATION IS EXTREMELY
IMPORTANT IN SUPPORTING THE LOAD!
•A common location is just above the bumper on the
bottom edge of the trunk or hatch.
•Use area with the greatest support.
•Do not place the lower frame on glass, plastic, or thin
metal.
•Many vehicle trunks and liftgates have a large section of
poorly supported metal that will dent under weight.
•Do not place FullBack on vehicle’s emblem.
TO AVOID DAMAGE, ALWAYS POSITION
FULLBACK WHERE DETERMINED BY
YOUR VEHICLE SPECIFIC FIT NOTES .
Position the FullBack
DID YOUR FIT NOTES
INDICATE YOU NEED
TO USE ANCHORS FOR
THE TOP HOOKS?
YES
NO
SKIP STEP 5 AND
PROCEED TO PAGE 4.
PROCEED TO STEP 5.
PROCEED TO PAGE 5.
•Using your body to help support the FullBack
attach both top strap hooks around the top
edge of the trunk lid, hatch lid or rear door.
Tighten top straps until FullBack is held in
place.
•You may need to attach hooks at a wider
section of the seam and then slide them into
their recommended place on the vehicle.
•Straps should be parallel, and no wider than
the body of the FullBack. Route the straps
over the FullBack frame.
•Not able attach the top hook? Use the anchor
configuration. Follow Anchor installation
instructions on PAGE 4.
•DO NOT ATTACH THE TOP HOOKS TO
PLASTIC OR TO A SPOILER. Use the Anchor
configuration instead. Follow Anchor
installation instructions on PAGE 4.
•DO NOT ATTACH THE TOP HOOKS TO GLASS.
Use the Glass Hatch Hooks (sold separately -
Yakima Part Number 8002612).
•REMOVE HOOKS BEFORE OPENING THE
HATCH OR TRUNK! Opening the hatch
or trunk with hooks installed could cause
damage to the vehicle.
Attach top hooks
1035059C-4/42
B
A
E
D
C
TOP HOOKS: Anchor installation instructions
Confirmed your vehicle does not require
Anchors? Skip this page.
WARNING:
DO NOT REST
THE ANCHORS
AGAINST GLASS.
Make sure the anchor
is free from contact
between hatch door
and vehicle’s frame
6
1035059C-5/42
•Not able to attach the bottom hooks? Use the Anchor
configuration. Follow Anchor installation instructions on page 6.
Attach bottom hooks
•REMOVE HOOKS BEFORE OPENING THE HATCH
OR TRUNK! Opening the hatch or trunk with
hooks installed could cause damage to the
vehicle.
•Acceptable attachment points may include the bottom edge of the trunk, hatch lid or
rear door. Additionally, the tie-down hooks underneath the vehicle or the metal ledge
of the bumper are acceptable. Only attach hooks to areas with sufficient support.
•You may need to attach hooks at a wider section of the seam and then slide
them into their recommended place on the vehicle.
•DO NOT ATTACH THE BOTTOM HOOKS TO PLASTIC OR TO
A SPOILER. Use the Anchor configuration instead. Follow
Anchor installation instructions on page 6.
•DO NOT ATTACH THE BOTTOM HOOKS TO GLASS.
Use the Glass Hatch Hooks (sold separately -
(Yakima Product Number 8002612).
PROCEED TO PAGE 7.
DID YOUR FIT NOTES
INDICATE YOU NEED
TO USE ANCHORS FOR
THE BOTTOM HOOKS?
YES
NO
SKIP STEP 6 AND
PROCEED TO PAGE 6.
PROCEED TO STEP 6.
1035059C-6/42
B
BOTTOM HOOKS: Anchor installation instructions
Confirmed your vehicle does not require
Anchors? Skip this page.
E FD
A
C
G H
BOTTOM HOOKS: Anchor installation instructions
Confirmed your vehicle does not
require Anchors? Skip this page.
REMOVE THE CARRIER FROM THE CAR.
BEFORE CLOSING
THE TRUNK:
Be sure the pads are
free from contact
between trunk door
and vehicle’s frame.
7
8
2X
2X
1035059C-7/42
•Using ample force pull both top straps toward the
front of the vehicle to fully tighten the top straps.
•Store the extra straps
using the rubber strap
storage bands.
Do not pull upper
straps sideways!
Fully Tighten bottom straps
Fully Tighten top straps
•Using ample
force pull both
bottom straps
down toward
the ground to
fully tighten the
bottom straps.
•Store the extra
straps using
the rubber
strap storage
bands.
1035059C-8/42
9
LOADING
10
Grasp the FullBack and
test that it’s securely
fastened to the vehicle
by trying to move it in
all directions. FULLBACK
SHOULD NOT MOVE!
Any Contact
with a spoiler is
unacceptable.
Test installation
Raise the support arms
•Rotate the left and right dials
toward the unlock icon and
raise the support arms.
•Support arms must
be parallel to one
another, and angled
slightly upward.
Ensure that
the left and
right dials
return to
their locked
positions.
•Pull downward on
both support arms
to ensure they are
locked into position.
The lock icons will be
aligned when locked.
1 2
3
1035059C-9/42
12
11
•Each bike requires
three ZipStripsTM.
•Rotate anti-sway cradle against
the seat tube.
•Insert ZipStripsTM into cradles and
push against bike frame until snug.
Secure the bikes
A Yakima TubeTopTM (see cover page) may be required to carry your bike safely.
Bikes should be as level as possible to avoid ground clearance issues and possible ejections.
Failure to load
bikes properly can
result in property
damage, personal
injury, or death.
Alternate bike directions
to avoid interference.
•Always load first bike with
chain away from vehicle.
Load Bikes
Rotate anti-
sway cradles
out of the way
for easier
loading.
•Bikes are to be loaded in the position closest to the vehicle.
•Use Wheel Strap to
secure bike’s front
wheel to its frame.
•Load heaviest bike first.
1035059C-10/42
13
14
Install safety strap.
•Secure loose
strap end.
Now that you’ve installed your
Yakima FullBack take a moment to
enjoy the beverage of your choice.
Use the built in bottle openers to
crack open a cold one!
•Use the safety
strap to secure
bike frames to
FullBack frame.
Lock bikes
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Yakima
Yakima
Yakima K682 Manual de usuario
Yakima
Yakima CopperHead Manual de usuario
Yakima
Yakima SkyBox 16 Manual de usuario
Yakima
Yakima GetOut Manual de usuario
Yakima
Yakima K1095 Manual de usuario
Yakima
Yakima PlateMate Manual de usuario
Yakima
Yakima KeelOver Manual de usuario
Yakima
Yakima K451 Manual de usuario
Yakima
Yakima K152 Manual de usuario
Yakima
Yakima HullyRollers Manual de usuario
Yakima
Yakima PR3041 Manual de usuario
Yakima
Yakima KayakStackers Manual de usuario
Yakima
Yakima Outdoorsman Manual de usuario
Yakima
Yakima HoldUp Plus2 Manual de usuario
Yakima
Yakima K1040 Manual de usuario
Yakima
Yakima FatCat 6 Manual de usuario
Yakima
Yakima forklift Manual de usuario
Yakima
Yakima FlipSide 4 Manual de usuario
Yakima
Yakima Universal QR Locking Skewer Manual de usuario
Yakima
Yakima SUPDawg Manual de usuario
