Xylem SENSUS PolluTherm Manual de usuario

User Manual

Power modules for heating and cooling meters

PolluTherm / PolluStat E / PolluFlow

M H 6122 INT, page 1

1. Use of the power supply modules

Basically there are two different calculator housings:

Calculator housing 1 (PolluTherm until 2007, PolluStat E and PolluFlow until 2010) indicated by a

lid that can be opened sideways; it is closed by a black plastic latch

Calculator housing 2 (PolluTherm from 2007 on, PolluTherm from 2010 on, PolluStat E and

PolluFlow from 2010 on) indicated by a lid that is opened from bottom to top with two locking

latches on the two bottom corners.

The assignment of the modules for the calculators can be taken from the table.

1.3 Power supply modules

Module

name Function Order

number Back-up

battery AA

PolluTherm

Calculator PolluStat E

Calculator PolluFlow

calculator

hous.

1 until

2007

hous.

2 from

2007

hous.

2 from

2010

hous.

1 until

2010

hous.

2 from

2010

hous.

1 until

2010

hous.

2 from

2010

Power

module

230 V / 3 V

Power

supply with

cable 230 V 68503917 X

Power

module

230 V / 3 V

Power

supply with

cable 230 V 68504679 X **

Power

module

230V /3,6V

Power

supply with

cable 230 V 68503876 X X

Power

module

230V /3,6V

Power

supply with

cable 230 V 68504532 3,6 V -JST-St.

68504900 * X X X

Power

module

24 V / 3 V

Power

supply with

cable

24 V AC

68504529 X **

Power

module

24 V / 3,6V

Power

supply with

cable

24 V AC

68504533 3,6 V -JST-St.

68504900 * X X X

* PolluStat E, PolluFlow and PolluTherm: when changing to power supply the back-up battery AA 3.6 V is

always included in the delivery

** Retrofitting to mains power is only possible after exchanging the integrator modules to the new version

2. Safety instructions

The above mentioned modules may only be used for the devices provided for in the list as otherwise

the modules or the heat meter could be damaged

Exchanging batteries with power supply units requires a careful handling of the batteries. Batteries

must not be recharged, short-circuited, put in contact with water or exposed to temperatures of more

than 80 °C

Power modules for calculator housing 1 have an internal back-up battery. The same safety

instructions as mentioned in the previous point apply

Power modules for calculator housing 2 do not have an internal back-up battery anymore; they can

be stored indefinitely

Batteries and electronic waste may only be disposed at suitable collection centers for professional

waste disposal

The connection of network modules may only be done by persons authorized and trained for that

purpose. Furthermore the generally accepted rules of technology and VDE 0100 in particular have to

be observed

Power module must be fed from supplies fused at 6 A protection

Before exchanging a power module the existing power module has to be switched off

When the power module is damaged it has to be scrapped and replaced with a new one

User Manual

Power modules for heating and cooling meters

PolluTherm / PolluStat E / PolluFlow

M H 6122 INT, page 2

3. Retrofitting or replacement of a power module

3.1. Opening of the calculator housing

Remove the lower user seal from the housing

Calculator housing 1: Open housing cover by opening the black housing latch

Calculator housing 2: Open housing by pressing both closing clips at the two bottom corners

3.2. Removal of battery and insert of power module

Calculator housing 2:

PolluStat E, PolluFlow, PolluTherm: before the supply battery is removed the calculator module has

to be dismantled from the calculator. PolluTherm (delivery from 2007 to 2010): the integrator module

has to be changed with a new one (from 2010 on). Unscrew only the screw from the plastic cover on

the right side under the KK1 seal (user seal) (picture 3). Pull out the calculator module. The seals in

the middle and on the left side may not be removed (invalidation of metrological sealing)!

PolluStat E, PolluFlow, PolluTherm (from 2010 on): plug on the back-up battery AA 3,6V (68504900)

to the backside of the calculator module (picture 4) (JST plug). The battery is required for date back-

up and short-term emergency operation in power failures. In PolluTherm (2007 to 2010) the back-up

battery is soldered-on to the circuit board as standard. These modules cannot be retrofitted to mains-

power supply.

Calculator housing 1 and 2:

Lift the battery or the power module and disconnect the output plug

For disposal note safety instructions, point 2

3.3. Installation of power supply unit

Plug the connection plug of the power module in the socket and insert the power module in the

designated recess of the housing.

In order to connect cables a spare rubber moulding has to be removed from the calculator housing 2.

Guide the cable through the rubber moulding and provide a strain relief with the cable binder.

Calculator housing 1: the cable has to be guided through the PG screw connection and fixed.

Plug the cable of the output plug in the supply plug (due to the different pins interchanging of the

power supply units is not possible).

Please ensure that the cable of the connection plug is not pinched by the calculator cover.

Close the calculator lid and seal with the provided self lock seal.

For detection of the power module it is necessary that the device is connected to the power system

for at least one minute.

Through a connector encoding the M-Bus credit automatically turns off when a power supply unit is

installed.

Picture 1: inside view with battery, calculator housing 2 Picture 2: inside view with power module, calculator housing 2

Connection plug

battery / power module

Battery:

C or D

Power

module

User Manual

Power modules for heating and cooling meters

PolluTherm / PolluStat E / PolluFlow

M H 6122 INT, page 3

Picture 3: calculator housing 2: removal of calculator module

Picture 5: inside view with battery calculator housing 1 Picture 6: inside view with power module calculator housing 1

3.4. Connection to electricity network

The power modules have a connecting cable of 1 m length.

The cable may only be connected to a 230V AC network by a person authorized and trained for that

purpose.

The connection should be made on a junction box.

24 V AC power modules are connected to power supply systems from controls or central control

technologies. These modules must not be connected to 24 V DC direct current

Since heat meters in calculator housing 1 do not count during a power supply interruption a reliable

power supply is important. In case of a power failure all stored values are retained and the internal

clock continues running via the back-up battery. Heat meters in calculator housing 2 continue

running for a limited time after a power failure. M-Bus communication, however, can be limited.

Material number: 28504962

Edition: 004-1101

Subject to change

Sensus GmbH Ludwigshafen

Industriestraße 16

D-67063 Ludwigshafen

Phone: +49 (0) 621 6904-1113

Fax: + (0) 621 6904-1409

E-Mail: [email protected]

Output plug

battery / power

module

Power

module

Back-up

battery

JST plug

Picture 4: calculator housing 2, back-up battery 3,6 V with JST

plug on the back side of the calculator module

Screw for disassembly

of calculator module

Calibration seal must

not be removed!

Otros manuales para SENSUS PolluTherm

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Xylem

Xylem

Xylem EXO Series Manual de usuario

Xylem

Xylem Sensus Domo R Manual de lista de piezas

Xylem

Xylem YSI Pro2030 Manual de usuario

Xylem

Xylem ebro PHT 810 Manual de usuario

Xylem

Xylem WTW pH 3110 Manual de usuario

Xylem

Xylem SonTek RiverSurveyor Manual de usuario

Xylem

Xylem wtw Cleaning Air Box -115 VAC Manual de usuario

Xylem

Xylem SonTek-SL Manual de usuario

Xylem

Xylem WTW Cond 3310 Manual de usuario

Xylem

Xylem WTW MPP 910 IDS Manual de usuario

Xylem

Xylem WTW Multi 9430 Manual de usuario

Xylem

Xylem Sensus PulseRF HRI-A3 Manual de usuario

Xylem

Xylem MJK 713 Manual de usuario

Xylem

Xylem Sensus iPERL Manual de usuario

Xylem

Xylem WTW LabStation LS Flex/430 Manual de usuario

Xylem

Xylem Sensus 412 Series Manual de usuario

Xylem

Xylem WTW photoLab 7600 UV-VIS Manual de usuario

Xylem

Xylem WTW SenTix ORP-T 900 Manual de usuario

Xylem

Xylem FLYGT CCD 301 Manual de usuario

Xylem

Xylem Sensus PolluCom F/S C Manual de usuario

Xylem

Xylem WTW pHotoFlex Turb Manual de usuario

Xylem

Xylem WTW Oxi 3205 Manual de usuario

Xylem

Xylem Sensus iPERL Manual de usuario

Xylem

Xylem SI Analytics HandyLab 600 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario