Winmate G-WIN GC Series Manual de usuario

Please read these instructions carefully before using this product, and save this manual for future use.

7”~23.8” G-WIN Panel PC

Intel® Celeron® N2930

GC Series

User Manual

Document Version 1.1

Document Part No. 91521110105A

G-WIN GC Series Panel PC

Contents

Preface 3

About This User Manual 7

Chapter 1: Introduction 8

1.1 Overview 9

1.2 Features 9

1.3 Package Content 9

1.4 Product Overview 10

Chapter 2: Getting Started 14

2.1 Turning On and Off Your Device 15

2.2 Operating the Panel PC 16

2.3 How to Enable Watchdog 16

2.4 Configuring Serial Port Settings 17

Chapter 3: Installation 18

3.1 Wiring Requirements 19

3.2 Connecting to Other Devices 19

Chapter 4: Mounting 22

4.1 RAM Mount 23

4.2 VESA Mount 24

4.3 Panel Mount 25

Chapter 5: BIOS Setup 26

5.1 When and How to Use BIOS Setup 27

5.2 BIOS Functions 27

5.3 BIOS Settings 28

5.4 Using Recovery Wizard to Restore Computer 50

Chapter 6: Driver Installation 51

4.1 Installing Chipset Driver 52

4.2 Installing Graphics Driver 54

4.3 Installing Intel Sideband Fabric Device (Intel MBI) 55

4.4 Installing Intel Trusted Engine Interface (TXE) Driver 56

4.5 Installing Intel Network Connections 57

4.6 Installing Audio Driver 58

4.7 Installing USB 3.0 Driver 59

Appendix 60

Appendix A: Specifications 60

Appendix B: Cleaning the Monitor 62

Appendix C: Winmate Software Development Kit 63

Preface

No part of this document may be reproduced, copied, translated, or transmitted in any form or

by any means, electronic or mechanical, for any purpose, without the prior written permission

of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

We reserve the right to make changes, without notice, to any product, including circuits and/or

software described or contained in this manual in order to improve design and/or performance.

We assume no responsibility or liability for the use of the described product(s) conveys no

license or title under any patent, copyright, or masks work rights to these products, and make

no representations or warranties that these products are free from patent, copyright, or mask

work right infringement, unless otherwise specified. Applications that are described in this

manual are for illustration purposes only. We make no representation or guarantee that such

application will be suitable for the specified use without further testing or modification.

Warranty

Our warranty guarantees that each of its products will be free from material and workmanship

defects for a period of one year from the invoice date. If the customer discovers a defect, we

will, at his/her option, repair or replace the defective product at no charge to the customer,

provide it is returned during the warranty period of one year, with transportation charges

prepaid. The returned product must be properly packaged in its original packaging to obtain

warranty service. If the serial number and the product shipping data differ by over 30 days, the

in-warranty service will be made according to the shipping date. In the serial numbers the third

and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,

with A for October, B for November and C for December).

For example, the serial number 1W18Axxxxxxxx means October of year 2018.

Customer Service

We provide a service guide for any problem by the following steps: First, visit the website of

our distributor to find the update information about the product. Second, contact with your

distributor, sales representative, or our customer service center for technical support if you

need additional assistance.

You may need the following information ready before you call:

Product serial number

Software (OS, version, application software, etc.)

Description of complete problem

The exact wording of any error messages

In addition, free technical support is available from our engineers every business day. We are

always ready to give advice on application requirements or specific information on the

installation and operation of any of our products.

G-WIN GC Series Panel PC

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful information or to

alert you to the potential for hardware damage or personal injury. These are Notes, Important,

Cautions, and Warnings. The following is an example of each type of advisory.

Note:

A note is used to emphasize helpful information

Important:

An important note indicates information that is important for you to know.

Caution A Caution alert indicates potential damage to hardware and explains how

to avoid the potential problem.

Attention Une alerte d’attention indique un dommage possible à l’équipement et

explique comment éviter le problème potentiel.

Warning! An Electrical Shock Warning indicates the potential harm from electrical

hazards and how to avoid the potential problem.

Avertissement !Un Avertissement de Choc Électrique indique le potentiel de

chocs sur des emplacements électriques et comment éviter ces problèmes.

Safety Information

Warning! Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections while the power is

on. Sensitive electronic components can be damaged by sudden power surges.

Only experienced electronics personnel should open the PC chassis.

Avertissement! Toujours débrancher le cordon d’alimentation du chassis

lorsque vous travaillez sur celui-ci. Ne pas brancher de connections lorsque

l’alimentation est présente. Des composantes électroniques sensibles peuvent être

endommagées par des sauts d’alimentation. Seulement du personnel expérimenté

devrait ouvrir ces chassis.

Caution Always ground yourself to remove any static charge before touching the

CPU card. Modern electronic devices are very sensitive to static electric charges. As

a safety precaution, use a grounding wrist strap at all times. Place all electronic

components in a static-dissipative surface or static-shielded bag when they are not in

the chassis.

Attention Toujours verifier votre mise à la terre afin d’éliminer toute charge

statique avant de toucher la carte CPU. Les équipements électroniques moderns

sont très sensibles aux décharges d’électricité statique. Toujours utiliser un bracelet

de mise à la terre comme précaution. Placer toutes les composantes électroniques

sur une surface conçue pour dissiper les charge, ou dans un sac anti-statique

lorsqu’elles ne sont pas dans le chassis.

Alternating Current !

The Protective Conductor Terminal (Earth Ground) symbol indicates the potential

risk of serious electrical shock due to improper grounding.

Mise à le terre ! Le symbole de Mise à Terre indique le risqué potential de

choc électrique grave à la terre incorrecte.

Preface

For your safety carefully read all the safety instructions before using the device. Keep this user

manual for future reference.

Always disconnect this equipment from any AC outlet before cleaning. Do not use liquid or

spray detergents for cleaning. Use a damp cloth.

For pluggable equipment, the power outlet must be installed near the equipment and must

be easily accessible.

Keep this equipment away from humidity.

Put this equipment on a reliable surface during installation. Dropping it or letting it fall

could cause damage.

The openings on the enclosure are for air convection and to protect the equipment from

overheating.

Do not cover the openings.

Before connecting the equipment to the power outlet make sure the voltage of the power

source is correct.

Position the power cord so that people cannot step on it. Do not place anything over the

power cord.

If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient over-voltage.

Never pour any liquid into an opening. This could cause fire or electrical shock.

Never open the equipment. For safety reasons, only qualified service personnel should

open the equipment.

All cautions and warnings on the equipment should be noted.

*Let service personnel to check the equipment in case any of the following

problems appear:

oThe power cord or plug is damaged.

oLiquid has penetrated into the equipment.

oThe equipment has been exposed to moisture.

oThe equipment does not work well or you cannot get it to work according to

the user manual.

oThe equipment has been dropped and damaged.

oThe equipment has obvious signs of breakage.

Do not leave this equipment in an uncontrolled environment where the storage

temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the

equipment.

Caution Use the recommended mounting apparatus to avoid risk of injury.

Attention Utiliser l’appareil de fixation recommandé pour éliminer le risque

de blessure.

Warning! Only use the connection cords that come with the product. When in

doubt, please contact the manufacturer.

Avertissement! Utiliser seulement les cordons d’alimentation fournis

avec le produit. Si vous doutez de leur provenance, contactez le

manufacturier.

Warning! Always ground yourself against electrostatic damage to the device.

Avertissement! Toujours vérifier votre mise à la terre afin que

l’équipement ne se décharge pas sur vous.

Cover workstations with approved anti-static material. Use a wrist strap connected

to a work surface and properly grounded tools and equipment.

Use anti-static mats, heel straps, or air ionizer for added protection.

Avoid contact with pins, leads, or circuitry.

G-WIN GC Series Panel PC

Turn off power and input signals before connecting test equipment.

Keep the work area free of non-conductive materials, such as ordinary plastic

assembly aids and Styrofoam.

Use filed service tools, such as cutters, screwdrivers that are conductive.

Always put drivers and PCB’s component side on anti-static foam.

Important Information

Federal Communications Commission Radio Frequency Interface Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class "B" digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference

at him own expense.

EC Declaration of Conformity

This equipment is in conformity with the requirement of the

following EU legislations and harmonized standards. Product also

complies with the Council directions.

Electromagnetic Compatibility Directive (2014/30/EU)

EN55024: 2010 EN 55022: 2010 Class B

oIEC61000-4-2: 2009

oIEC61000-4-3: 2006+A1: 2007+A2: 2010

oIEC61000-4-4: 2012

oIEC61000-4-5: 2014

oIEC61000-4-6: 2013

oIEC61000-4-8: 2010

oIEC61000-4-11: 2004

EN55022: 2010/AC:2011

EN61000-3-2:2014

EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

General Guideline

It is recommended to reboot the device when some functions are defect or inactive. If it still can't

solve the problems please contact your dealer or agent.

About This User Manual

This User Manual provides information about using the Winmate® G-WIN GC Series Panel

PC. This User Manual applies to the GC Series Panel PC.

The documentation set for the GC Series Panel PC provides information for specific user

needs, and includes:

GC Series Panel PC User Manual –contains detailed description on how to use the

panel PC, its components and features.

GC Series Panel PC Quick Start Guide –describes how to get the panel PC up and

running.

Note:

Some pictures in this guide are samples and can differ from actual product.

Document Revision History

Version

Date

Note

1.0

11-Jul-2019

Initial document release

1.1

25-Nov-2019

Add R19IB3S-GCM1, W22IB3S-GCA3,

W24IB3S-GCA2

G-WIN GC Series Panel PC

Chapter 1: Introduction

This chapter gives you product overview, describes features and hardware

specification. You will find all accessories that come with the panel PC in

the packing list. Mechanical dimensions and drawings included in this

chapter.

Chapter 1: Introduction

1.1 Overview

Congratulations on purchasing Winmate® GC65 Panel PC. The elegantly designed, yet

rugged, industrial grade G-WIN GC series is designed for heavy duty applications. With rugged

construction, ultimate computing power, GC65 series are guaranteed to meet "heavy duty"

needs. This series feature high computing power and user-friendly interface with projected

capacitive multi-touch (PCAP) technology and support Windows® operating systems. Rugged

housing provides front IP65 protection against outer dust and water splash.

1.2 Features

Winmate® GC65 Panel PC features:

7”~23.8” PCAP touch screen

Low power consumption with Intel® Celeron® N2930

Front IP65 for protection against water and dust

A true flat, easy-to-clean front surface with edge-to-edge design

Plenty of I/O, including 2 x LAN, 1 x RS232/422/485,

1 x USB3.0, 1 x USB 2.0, 1 x HDMI

1.3 Package Content

Carefully remove the box and unpack your device. Please check if all the items listed below are

inside your package. If any of these items are missing or damaged contact us immediately.

Standard factory shipment list:

Panel PC

Quick Start Guide

(Hardcopy)

Driver CD & User Manual

Varies by product

specifications

Part No. 9152111I102F

Part No. 9171111I103M

AC Adapter 12V/ 50W

Power Cable

Terminal Block 3 Pin

Part No. 922D050W12VA

Varies by country

Part No. 94J602G030K0

G-WIN GC Series Panel PC

1.4 Product Overview

7”, W07IB3S-GCO1 Unit: mm

10.1”, W10IB3S-GCH1(HB) Unit: mm

№

Description

№

Description

①

1x RS232/422/485 (Default RS232)

⑤

12V DC in Power Jack

②

1 x USB 3.0, 1 x USB 2.0

⑥

OSD Control Panel

③

1 x HDMI 1.4a

⑦

1 Watt Speaker

④

2 x RJ 45-10/100/1000 Mbps

№

Description

№

Description

①

1x RS232/422/485 (Default RS232)

⑤

12V DC in Power Jack

②

1 x USB 3.0, 1 x USB 2.0

⑥

OSD Control Panel

③

1 x HDMI 1.4a

⑦

1 Watt Speaker

④

2 x RJ 45-10/100/1000 Mbps

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel táctil de Winmate

Winmate

Winmate R10FA3S-GST2 Manual de usuario

Winmate

Winmate R10IB3S-67T2 Manual de usuario

Winmate

Winmate R15IH3S-MRA3FP Manual de usuario

Winmate

Winmate R15IB3S-65A1FTP Manual de usuario

Winmate

Winmate W10IB3S-GSH1HB Manual de usuario

Winmate

Winmate W10IE3S-MRH2FP Manual de usuario

Winmate

Winmate W05TA3S-PCT3AC Manual de usuario

Winmate

Winmate R15IB3S-65EX Manual de usuario

Winmate

Winmate W22IK3S-SPA3 Manual de usuario

Winmate

Winmate R10IB3S-SPT269 Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Winmate

Winmate G-WIN Slim IP65 Manual de usuario

Winmate

Winmate R15IH3S-67A3HB Manual de usuario

Winmate

Winmate W07IB3S-POT1 Manual de usuario

Winmate

Winmate EL Series Manual de usuario

Winmate

Winmate R19IB7T-GCM1 Manual de usuario

Winmate

Winmate R19IHAT-66EX Manual de usuario

Winmate

Winmate P Series Manual de usuario

Winmate

Winmate W07FA3S-GCM1 Manual de usuario

Winmate

Winmate GC Series Manual de usuario

Winmate

Winmate M185D Manual de usuario

Winmate

Winmate B Series Manual de usuario

Winmate

Winmate R17IW3S-SPM1 Manual de usuario

Winmate

Winmate R15IB3S-65EX Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario