Winmate R10IB3S-SPT269 Manual de usuario

Please read this instructions before operating the device and retain them for future reference.

Flat Stainless

P-Cap Panel PC

Intel®Celeron®Bay Trail-M N2930, 1.83 GHz

Full IP69K

User Manual

Version 1.0

User Manual Contents

- 2 -

CONTENTS

PREFACE ...............................................................................................................- 4 -

ABOUT THIS USER MANUAL .............................................................................- 11 -

CHAPTER 1: INTRODUCTION.............................................................................- 13 -

1.1 Product Features ..................................................................................- 13 -

1.2 Package Content ..................................................................................- 14 -

1.3 Connector Placement ...........................................................................- 15 -

1.4 Physical Buttons and LED Indicators....................................................- 16 -

1.5 Schematics and Dimensions.................................................................- 17 -

1.5.1 Dimensions 10.4"........................................................................- 17 -

1.5.2 Dimensions 15"...........................................................................- 17 -

1.5.3 Dimensions 19” ...........................................................................- 18 -

1.5.4 Dimensions 21.5” ........................................................................- 18 -

CHAPTER 2: GETTING STARTED ......................................................................- 20 -

2.1 Powering On.........................................................................................- 20 -

2.1.1 AC Adapter Components ............................................................- 20 -

2.1.2 Power Considerations.................................................................- 21 -

2.1.3 Power Consumption....................................................................- 21 -

2.1.4 Connecting the Power.................................................................- 22 -

2.2 Connector Pin Assignments..................................................................- 23 -

2.2.1 Power Cable................................................................................- 23 -

2.2.2 Serial Cable.................................................................................- 24 -

2.2.3 Ethernet Cable............................................................................- 25 -

2.2.4 USB 2.0 Cable ............................................................................- 26 -

2.3 Turning On and Off...............................................................................- 27 -

2.4 Cleaning the Monitor.............................................................................- 27 -

CHAPTER 3: OPERATING THE DEVICE ............................................................- 29 -

3.1 Operating System.................................................................................- 29 -

3.2 Multi-Touch...........................................................................................- 30 -

3.3 How to Enable Watchdog .....................................................................- 31 -

CHAPTER 4: AMI UEFI BIOS SETUP..................................................................- 34 -

User Manual Contents

- 3 -

4.1 When and How to Use BIOS Setup......................................................- 34 -

4.2 BIOS Functions.....................................................................................- 34 -

4.2.1 Main Menu ..................................................................................- 36 -

4.2.2 Advanced Menu..........................................................................- 38 -

4.2.3 Chipset Menu..............................................................................- 61 -

4.2.4 Security Menu .............................................................................- 62 -

4.2.5 Boot Configuration ......................................................................- 63 -

4.2.6 Save & Exit..................................................................................- 65 -

4.3 Using Recovery Wizard to Restore Computer..............................................- 67 -

CHAPTER 5: DRIVER INSTALLATION ...............................................................- 70 -

5.1 Installing Chipset Driver........................................................................- 70 -

5.2 Installing Graphics Driver......................................................................- 72 -

5.3 Installing Intel Sideband Fabric Device (Intel MBI) Driver (Windows 8) - 73 -

5.4 Installing Intel Trusted Engine Interface (Intel TXE) Driver ...................- 74 -

5.5 Installing Intel Network Connections.....................................................- 75 -

5.6 Installing Audio Driver...........................................................................- 76 -

CHAPTER 6: MOUNTING.....................................................................................- 78 -

6.1 Cable Mounting Considerations............................................................- 78 -

6.2 Safety Precautions................................................................................- 79 -

6.3 Mounting Guide.....................................................................................- 79 -

6.3.1 VESA Mount................................................................................- 80 -

6.3.2 Yoke Mount.................................................................................- 81 -

CHAPTER 7: TECHNICAL SUPPORT.................................................................- 83 -

7.1 Software Developer Support.................................................................- 83 -

7.2 Problem Report Form ...........................................................................- 84 -

APPENDIX A: PRODUCT SPECIFICATIONS......................................................- 86 -

APPENDIX B: ORDER INFORMATION ...............................................................- 90 -

User Manual Preface

- 4 -

PREFACE

No part of this document may be reproduced, copied, translated, or transmitted in

any form or by any means, electronic or mechanical, for any purpose, without the

prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their

respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product,

including circuits and/or software described or contained in this manual in order to

improve design and/or performance. We assume no responsibility or liability for

the use of the described product(s) conveys no license or title under any patent,

warranties that these products are free from patent, copyright, or mask work right

infringement, unless otherwise specified. Applications that are described in this

manual are for illustration purposes only. We make no representation or guarantee

that such application will be suitable for the specified use without further testing or

modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from

material and workmanship defects for a period of one year from the invoice date. If

the customer discovers a defect, we will, at his/her option, repair or replace the

defective product at no charge to the customer, provide it is returned during the

warranty period of one year, with transportation charges prepaid. The returned

product must be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by over 30 days,

the in-warranty service will be made according to the shipping date. In the serial

numbers the third and fourth two digits give the year of manufacture, and the fifth

digit means the month (e. g., with A for October, B for November and C for

December).

For example, the serial number 1W14Axxxxxxxx means October of year 2014.

User Manual Preface

- 5 -

Customer Service

We provide a service guide for any problem by the following steps: First, visit the

website of our distributor to find the update information about the product. Second,

contact with your distributor, sales representative, or our customer service center

for technical support if you need additional assistance.

You may need the following information ready before you call:

Product serial number

Software (OS, version, application software, etc.)

Description of complete problem

The exact wording of any error messages

In addition, free technical support is available from our engineers every business

day. We are always ready to give advice on application requirements or specific

information on the installation and operation of any of our products.

User Manual Preface

- 6 -

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful

information or to alert you to the potential for hardware damage or personal injury.

These are Notes, Important, Cautions, and Warnings. The following is an example of

each type of advisory.

NOTE:

A note is used to emphasize helpful information

IMPORTANT:

An important note indicates information that is important for you to

know.

CAUTION/ ATTENTION

A Caution alert indicates potential damage to hardware and explains

how to avoid the potential problem.

Une alerte d’attention indique un dommage possible à l’équipement et

explique comment éviter le problème potentiel.

WARNING!/ AVERTISSEMENT!

An Electrical Shock Warning indicates the potential harm from

electrical hazards and how to avoid the potential problem.

Un Avertissement de Choc Électrique indique le potentiel de chocs

sur des emplacements électriques et comment éviter ces problèmes.

ALTERNATING CURRENT / MISE À LE TERRE!

The Protective Conductor Terminal (Earth Ground) symbol indicates

the potential risk of serious electrical shock due to improper

grounding.

Le symbole de Mise à Terre indique le risqué potential de choc

électrique grave à la terre incorrecte.

User Manual Preface

- 7 -

Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your chassis

whenever you work with the hardware. Do not make connections

while the power is on. Sensitive electronic components can be

damaged by sudden power surges. Only experienced electronics

personnel should open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis lorsque

vous travaillez sur celui-ci. Ne pas brancher de connections

lorsque l’alimentation est présente. Des composantes

électroniques sensibles peuvent être endommagées par des sauts

d’alimentation. Seulement du personnel expérimenté devrait ouvrir

ces chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge before touching

the CPU card. Modern electronic devices are very sensitive to static

electric charges. As a safety precaution, use a grounding wrist strap

at all times. Place all electronic components in a static-dissipative

surface or static-shielded bag when they are not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute charge

statique avant de toucher la carte CPU. Les équipements

électroniques moderns sont très sensibles aux décharges

d’électricité statique. Toujours utiliser un bracelet de mise à la terre

comme précaution. Placer toutes les composantes électroniques

sur une surface conçue pour dissiper les charge, ou dans un sac

anti-statique lorsqu’elles ne sont pas dans le chassis.

User Manual Preface

- 8 -

Safety Precautions

For your safety carefully read all the safety instructions before using the

device. Keep this user manual for future reference.

Always disconnect this equipment from any AC outlet before cleaning.

Do not use liquid or spray detergents for cleaning. Use a damp cloth.

For pluggable equipment, the power outlet must be installed near the

equipment and must be easily accessible.

Keep this equipment away from humidity.

Put this equipment on a reliable surface during installation. Dropping it

or letting it fall could cause damage.

The openings on the enclosure are for air convection and to protect the

equipment from overheating.

CAUTION/ATTENTION

Do not cover the openings!

Ne pas couvrir les ouvertures!

Before connecting the equipment to the power outlet make sure the

voltage of the power source is correct.

Position the power cord so that people cannot step on it. Do not place

anything over the power cord.

If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient over-voltage.

Never pour any liquid into an opening. This could cause fire or electrical

shock.

Never open the equipment. For safety reasons, only qualified service

personnel should open the equipment.

All cautions and warnings on the equipment should be noted.

*Let service personnel to check the equipment in case any of the

following problems appear:

oThe power cord or plug is damaged.

oLiquid has penetrated into the equipment.

oThe equipment has been exposed to moisture.

oThe equipment does not work well or you cannot get it to work

according to the user manual.

oThe equipment has been dropped and damaged.

oThe equipment has obvious signs of breakage.

Do not leave this equipment in an uncontrolled environment where the

storage temperature is below -20°C (-4°F) or above 60°C (140°F). It may

damage the equipment.

User Manual Preface

- 9 -

CAUTION/ATTENTION

Use the recommended mounting apparatus to avoid risk of

injury.

Utiliser l’appareil de fixation recommandé pour éliminer le risque

de blessure.

WARNING! / AVERTISSEMENT!

Only use the connection cords that come with the product.

When in doubt, please contact the manufacturer.

Utiliser seulement les cordons d’alimentation fournis avec le

produit. Si vous doutez de leur provenance, contactez le

manufacturier.

WARNING!/ AVERTISSEMENT!

Always ground yourself against electrostatic damage to the

device.

Toujours vérifier votre mise à la terre afin que l’équipement ne

se décharge pas sur vous.

Cover workstations with approved anti-static material. Use a wrist

strap connected to a work surface and properly grounded tools and

equipment.

Use anti-static mats, heel straps, or air ionizer for added protection.

Handle electrostatic-sensitive components, PCB’s and assemblies by

the case or the edge of the board.

Avoid contact with pins, leads, or circuitry.

Turn off power and input signals before inserting and removing

connectors or test equipment.

Keep the work area free of non-conductive materials, such as

ordinary plastic assembly aids and Styrofoam.

Use filed service tools, such as cutters, screwdrivers, and vacuum

cleaners that are conductive.

Always put drivers and PCB’s component side on anti-static foam.

User Manual Preface

- 10 -

Important Information

Federal Communications Commission Radio Frequency Interface Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class "B"

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at him own expense.

European Union

This equipment is in conformity with the requirement of the

following EU legislations and harmonized standards.

Product also complies with the Council directions.

Electromagnetic Compatibility Directive (2014/30/EU)

EN55024: 2010/ A1: 2015

oIEC61000-4-2: 2009

oIEC61000-4-3: 2006+A1: 2007+A2: 2010

oIEC61000-4-4: 2012

oIEC61000-4-5: 2014

oIEC61000-4-6: 2014

oIEC61000-4-8: 2010

oIEC61000-4-11: 2004

EN55032: 2012/AC:2013

EN61000-3-2:2014

EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:201

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel táctil de Winmate

Winmate

Winmate W07FA3S-PCM1AC-PoE Manual de usuario

Winmate

Winmate R19IK3S-SPM169 Manual de usuario

Winmate

Winmate W10IB3S-PCH2AC-PoE S-Series Manual de usuario

Winmate

Winmate R08IB3S-VMU1 Manual de usuario

Winmate

Winmate R17IK3S-RKA1ML Manual de usuario

Winmate

Winmate G-WIN GC Series Manual de usuario

Winmate

Winmate R15IK3S-POC3 Manual de usuario

Winmate

Winmate W10IB3S-GSH1 Manual de usuario

Winmate

Winmate W05TA3S-PCT3AC Manual de usuario

Winmate

Winmate W15IB3S-PTA3 Manual de usuario

Winmate

Winmate W10IB3S-MRH2 Manual de usuario

Winmate

Winmate GC Series Manual de usuario

Winmate

Winmate ATEX R19IHAT-66EX-T Manual de usuario

Winmate

Winmate R15IW3S-SPC3 Manual de usuario

Winmate

Winmate W07IB3S-PCM1AC Manual de usuario

Winmate

Winmate R10IB3S-SPT2 Manual de usuario

Winmate

Winmate R15IB3S-65A1FTP Manual de usuario

Winmate

Winmate W07IB3S-PCO1-POE Manual de usuario

Winmate

Winmate 7'' S-Series Manual de usuario

Winmate

Winmate W10IB3S-EHH2 Manual de usuario

Winmate

Winmate W22IB3S-PCA3 PPC Manual de usuario

Winmate

Winmate R15IH3S-MRA3FP Manual de usuario

Winmate

Winmate W19IB3S-CHA1 Manual de usuario

Winmate

Winmate R15IB3S-65EX Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario