Vivotek Supreme MD8531H Manual de usuario

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Refer to your user’s manual for

the operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

Replacing or failing to properly install

the waterproof components, e.g.,

cables or cable glands, will void our

IP65/66/67 warranty.

Software CD

MD8531H

Quick Installation Guide

Screwdriver

Alignment Sticker

Package Contents

Desiccant bag

Focus Adjustment Tool Screws

EN - 2

General I/O Terminal Block

MD8531H

IMPORTANT:

Record the MAC address before installing

the camera.

Screw Holes

Physical Description

Inner View

Outer View

Lens

MicroSD/SDHC Card Slot

Waterproof Level: IP66

Reset button

Status LED

Screw Holes

RJ45 connector

Microphone

EN - 3

English

First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your

MicroSD/SDHC Card if necessary.

Dome Cover

Hardware Installation

Tamper-proof Screw

Camera Base

Plastic Cover

RJ45 Cable Dimension

2. Strip part of the sheath from the Ethernet

cable.

1. Drill a hole on the rubber seal plug and insert

an Ethernet cable through the opening.

Rubber Seal Plug

Assembling Steps

Recommended cable diameter: 5 to 8mm (Use CAT5e only)

3.1 Connecting RJ45 Ethernet Cable

EN - 4

o: white/orange stripe

O: orange solid

g: white/green stripe

B: blue solid

b: white/blue stripe

G: green solid

br: white/brown stripe

BR: brown solid

3. You will need an RJ45 crimping tool to attach the Ethernet wires to a connector. When done,

connect the cable to the camera’s Ethernet RJ45 socket.

EN - 5

English

3.2 Connecting IO cables:

17mm

1. Remove the waterproof connector from the camera, and pass IO wires through the rubber seal

as shown below. Tighten up and install the connector when done.

1 DI-

2 DI+

3 DO-

4 DO+

5 Audio GND

6 Audio Out

2. Use a small-size at-blade screwdriver to secure IO

wires to the included terminal blocks.

The pinouts are shown below.

Wire range: 1.5mm~1.8mm; 20AWG

Strip length: 6~7mm

Screw: M2

EN - 6

3. Connect the terminal block to the camera.

NOTE:

1. This equipment is only to be connected to PoE networks without routing to outside plants.

2. For PoE input connection, use only UL listed I.T.E. with PoE output.

EN - 7

English

Then, follow the steps below to install the camera to either a ceiling or wall:

1. Attach the supplied alignment sticker to the ceiling/wall.

2. Using the 4 screw circles on the sticker, drill 4 pilot holes into the ceiling/wall. Then hammer the

plastic anchors into the holes if necessary.

3. This Network Camera can be mounted with the cable routed through the ceiling/wall or from the

side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the

picture. If the cable goes through the rear opening of the dome cover, please remove the plastic

cover (B).

4. Through the 4 holes on the camera base, insert the screws to corresponding holes and secure

the camera base with a screwdriver.

23A

3.3 Ceiling Mount

EN - 8

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is ana-

lyzed, please click on the “Next” button to continue the program.

Assigning an IP Address

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras

on the same LAN.

4. After a brief search, the main installer window will pop up. Double-click on the MAC address

that matches the one printed on the camera label or the serial number on the package box

label to open a browser management session with the Network Camera.

For further setup, please refer to the user's manual on the software CD.

Ready to Use

1. A browser session with the Network Camera should prompt as shown below.

2. You should be able to see live video from your camera. You may also install the 32-channel

recording software from the software CD in a deployment consisting of multiple cameras. For

its installation details, please refer to its related documents.

EN - 9

English

To adjust the viewing angle

90°

Adjusting the Lens

1. Loosen the lens module retention screw (not removing it) on top of the lens module.

2. Adjust the lens to a desired viewing angle.

3. When done, fasten the screw so that lens orientation can be xed and withstand shock and

vibration.

Fine-tune the Camera Focus

The focus of this network camera is set from 1.0 meter to

innity by factory default. If you want to focus on objects

closer than 1.0m or the lens has lost focus, please ne

tune it in the following way.

1. Loosen the retention scew on top of the lens

module.

2. Rotate the lens module to the side to access the

lens focus retention screw.

3. Loosen the focus retentation screw.

NOTE:

You can also rotate the lens module to correct the eld

of view when mounted on a tilted surface.

Otros manuales para Supreme MD8531H

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vivotek

Vivotek

Vivotek SD8362E-SS Manual de usuario

Vivotek

Vivotek FE8191 Manual de usuario

Vivotek

Vivotek IP7142 Manual de usuario

Vivotek

Vivotek IP8362 Manual de usuario

Vivotek

Vivotek FD8361L Manual de usuario

Vivotek

Vivotek IB8354-C Manual de usuario

Vivotek

Vivotek MD8562 Manual de usuario

Vivotek

Vivotek IP816A-LPC-v2 Manual de usuario

Vivotek

Vivotek FD9165-HT-A Manual de usuario

Vivotek

Vivotek IP8352 Manual de usuario

Vivotek

Vivotek PD8136 Manual de usuario

Vivotek

Vivotek IP7130 Manual de usuario

Vivotek

Vivotek FD8135H Manual de usuario

Vivotek

Vivotek IP7153 Manual de usuario

Vivotek

Vivotek CC8130 Manual de usuario

Vivotek

Vivotek FD8133 Manual de usuario

Vivotek

Vivotek IP3137 Manual de usuario

Vivotek

Vivotek MD7530 Manual de usuario

Vivotek

Vivotek IP8371E Manual de usuario

Vivotek

Vivotek SD8161 Manual de usuario

Vivotek

Vivotek IP8355EH Manual de usuario

Vivotek

Vivotek FE8173 Manual de usuario

Vivotek

Vivotek IB9367-HT Manual de usuario

Vivotek

Vivotek IB8354-C Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario