Vivotek IP8362 Manual de usuario
EN-1
English
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN-2
Package Contents
1
Software CD
IP8362
Quick Installation Guide /
Warranty Card
Waterproof Connector (for backup
use)
Alignment Sticker
Wall Mount Bracket
Sun Shield
Wrench / RJ45 Female/Female Coupler / Double-sided Tape / Screws
Power Adapter
Moisture Absorber
EN-3
English
Physical Description
2
IR LED
Lens
Light Sensor
General I/O
Terminal Block
SD/SDHC Card Slot
Zoom Controller
Focus Controller
Reset Button
General I/O Terminal Block
Ethernet 10/100
RJ45 Plug
Power Cord Socket
+ AC 24V +
- AC 24V -
When inserting an SD/SDHC card,
note the orientation of the contacts.
EN-4
1
2
5
4
3
6
5
4
6
1. Attach the alignment sticker to the wall. Drill three holes into the wall. Then hammer the supplied
plastic anchors into the holes and secure the plate with supplied screws.
2. Feed the cables through the front opening of the wall mount bracket. (If you want to use external
devices such as sensors and alarms, please refer to the assembling steps on the next page.)
3. Hang the wall mount bracket on the plate.
4. Fix the Network Camera on the wall mount bracket with two screws on both sides.
5. Secure the wall mount bracket with the supplied screws.
6. Adjust the angle of the wall mount bracket to aim at the shooting area.
Hardware Installation
3
The supplied L-type hex key wrenches
are exclusively designed to match each
screw. In case you will need to adjust the
lens later, do not discard the wrenches.
EN-5
English
Waterproof Connector
1 Power +12V
2 Digital Output
3 Digital Input
4 Ground
5 RS485 +
6 RS485 -
7 Ground
8 Audio Input
9 Ground
10 Audio Output
87654321 109
1. Disassemble the components of the waterproof connector into part (A) ~ (F) as shown above.
2. Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A)
and screw nut (B) tightly.
3. Open the back cover of the Network Camera.
4. If you have external devices such as sensors and alarms, feed the cables through the waterproof
connector (F --> E --> C --> A+B) as the illustration shown below. Then refer to the pin definition
to connect them to the general I/O terminal block. Note: The recommended cable gauge is 2.0 ~ 2.8
mm.
5. Push the seal (C) into the housing (E).
6. Insert the seals (D) into the empty holes on the seal (C) to avoid moisture.
7. Secure the sealing nut (F) tightly.
8. Tighten the back cover.
9. Remove rubber (G) and feed the cables through the wall mount bracket.
Components of the Waterproof Connector
Seals (D)
Housing (E)
Sealing Nut (F)
Seal (C)
Screw Nut (B)
Pin Definition
Assembling Steps
Rubber (A)
(A)+(B)
2
6
(E)
(C)
(F)
(D)
(C)
4
7
(E)
(F)
3
(C)
5
8
9
(F)
(G)
EN-6
Network Deployment
4
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
Non-PoE Switch
PoE Power Injector
(optional)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
EN-7
English
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one on the product label to connect to the Network Camera via Internet Explorer.
Network Camera
Model No: IP8362
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
MAC:0002D1730202
RoHS
0002D1730202
00-02-D1-73-02-02 192.168.5.151 IP8362
Installation
Wizard 2
IW
2
Assigning an IP Address
5
EN-8
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. Access the Network Camera from the LAN.
2. Retrieve live video through a web browser or recording software.
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
N
3
4
EN-9
English
5. Tighten the lens cover.
6. Replace the moisture absorber with a new one if you open the back cover during the
installation procedure.
Note
If you want to use the supplied sun shield for outdoor environments, please follow the steps below to
install:
1. Tighten the supplied two screws.
2. Attach the supplied sun shield to the Network Camera and slide it to the desired position.
3. Fix the sun shield with the supplied two screws.
5
6
12
3
Please tear down the aluminum foil vacuum
bag and take out the moisture absorber,
then attach the moisture absorber with the
supplied double-sided tape.
Otros manuales para IP8362
3
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vivotek
Vivotek
Vivotek IP8362 Manual de usuario
Vivotek
Vivotek FD9389-EHV-v2 Manual de usuario
Vivotek
Vivotek IP8371E Manual de usuario
Vivotek
Vivotek SD8362E Manual de usuario
Vivotek
Vivotek IP7161 Manual de usuario
Vivotek
Vivotek IP8361 Manual de usuario
Vivotek
Vivotek 4X-IP7133 Manual de usuario
Vivotek
Vivotek FD8361 Manual de usuario
Vivotek
Vivotek PZ8111 Manual de usuario
Vivotek
Vivotek PZ7132 Manual de usuario
Vivotek
Vivotek SD8362E-SS Manual de usuario
Vivotek
Vivotek IP8152 Manual de usuario
Vivotek
Vivotek PT1111M Manual de usuario
Vivotek
Vivotek ip8364-c Manual de usuario
Vivotek
Vivotek FD8167 Manual de usuario
Vivotek
Vivotek IP8173H Manual de usuario
Vivotek
Vivotek IP7161 Manual de usuario
Vivotek
Vivotek FE9192-H Manual de usuario
Vivotek
Vivotek FD9187-HT-A Manual de usuario
Vivotek
Vivotek FD8156 Manual de usuario
