Vivo Mount-E-FD55 Manual de usuario
Remote Control Motorized TV
Ceiling Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
- -Model: MOUNT E FD55
Tools Required:
electric drill, phillips screwdriver
Scan the QR code with your mobile device or follow the
link to helpful videos and specifications related to this
product.
- - -https://vivo us com/products/mount e fd55
Caution!
1. Make sure the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
2. Tighten screws firmly, but do not over tighten, which causes damage to the product and
reduces its holding power.
3. Please do not disassemble or change the electronic components of the product without
authorization.
Package Contents
1
Assembly Steps
Step 1: Hang Ceiling Mount
Using ceiling template (C), mark
exact location of mounting holes.
Drill pilot holes 2.2” deep, using a
4. mm drill bit. Insert two screws
(W-A), leaving a mm gap from
ceiling.
Option A: For Wooden Ceilings
11
2
2
33
Option B: For Concrete Ceilings
Using ceiling template (C), mark
exact location of mounting holes.
Drill pilot holes 2.4” deep, using a
10mm drill bit. Insert six concrete
anchors (W-B), then tighten two
screws (W-A), leaving a mm gap
from ceiling.
1
2
3
1
2
3
OR
Hang the ceiling mount so that the
screws fit into the keyhole
openings. Slide mount forward,
then secure using additional
screws (W-A) with washers (W-C).
Tighten all screws.
Hang the ceiling mount so that the
screws fit into the keyhole
openings. Slide mount forward,
then secure using additional
screws (W-A) with washers (W-C).
Tighten all screws.
Step 2: Installing the VESA Plate
Remove the two bottom screws from
the VESA plate (B) and set aside for
later use.
Remove the screws from the VESA
adapters (E, F).
(if mounting a TV with a VESA pattern larger than 200 x 200mm)
Align the VESA adapters with the
VESA plate and assemble, using
screws previously removed from the
VESA adapters.
OPTIONAL
2
Step 2: (Continued)
Align the VESA plate with the mounting holes in the back of the TV screen. Install
VESA plate to TV using appropriate screws and washers according to your screen
type.
Option A: For Flat Back Screens
Option B: For Recessed Back Screens or to Access A/V Inputs
Align the VESA plate with the mounting holes in the back of the TV screen. Install
VESA plate to TV using appropriate screws and washers according to your screen
type.
OR
Step 3: Hooking the TV onto the Ceiling Mount
Insert upper center screw on VESA plate into keyhole hook.
Using screws previously removed (in beginning of step 2), fasten VESA plate
to ceiling mount.
Clearance between the ceiling and top edge of TV should be no less than
1 mm when TV is in the fully lowered position.
3
Using cable ties (J), fasten cables.
Step 4: Run Cables and Install Covers
Run cables along edge of mount.
Allow slack in cables for arm
movement. Place covers over
cables and snap into place.
Step 5: Installing the IR Receiver
Note: Plugging power supply into AC outlet prior to the mount may cause a
large spark when connecting to the mount.
Don’t run any cables through the mount motion space.
NOTE:
Peel the backing paper. Place IR receiver (G) on TV as desired. Ensure
nothing will obstruct the transmission from where the TV will be viewed.
Plug IR receiver (G) into mount. Plug power supply (I) into mount, and
connect to AC outlet.
Safety Warning
If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
Contact us at:
Email: help@vivo-us.com
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Last Updated: 04/26/2018 4
Otros manuales para Mount-E-FD55
4
Otros manuales de Rack y soporte de Vivo
Vivo
Vivo MOUNT-UDLS1 Manual de usuario
Vivo
Vivo STAND-V002C Manual de usuario
Vivo
Vivo DESK-AC06-2B Manual de usuario
Vivo
Vivo STAND-VAD3 Manual de usuario
Vivo
Vivo STAND-SHELF60B Manual de usuario
Vivo
Vivo STAND-V001D Manual de usuario
Vivo
Vivo STAND-TDML3 Manual de usuario
Vivo
Vivo STAND-TV65A Manual de usuario
Vivo
Vivo MOUNT-ALL02 Manual de usuario
Vivo
Vivo STAND-V002VA Manual de usuario
Vivo
Vivo STAND-TV65A Manual de usuario
Vivo
Vivo MOUNT-VP01B Manual de usuario
Vivo
Vivo STAND-V012C Manual de usuario
Vivo
Vivo DESK-V000K-M2/G/W Manual de usuario
Vivo
Vivo Sonos Play 5 Manual de usuario
Vivo
Vivo DESK-SKIRT-60P Manual de usuario
Vivo
Vivo STAND-SIT1B Manual de usuario
Vivo
Vivo MOUNT-KB05HB Manual de usuario
Vivo
Vivo STAND-V006 Manual de usuario
Vivo
Vivo MOUNT-SONOS3W Manual de usuario
