Vivo MOUNT-KB35B Manual de usuario
Black Pneumatic Wall Mounted Keyboard Tray
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-kb35b
SKU: MOUNT-KB35B
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
for further assistance. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
13.2lbs
(6kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
3
PACKAGE CONTENTS
A (x1)
Wall Plate
S-A (x8)
M5x10mm Screw
S-B (x4)
M4x6mm Screw
NOTE: SOME HARDWARE MAY NOT BE USED
Drill Pencil
Stud Finder Phillips
Screwdriver
B (x1)
Arm Extension
C (x1)
Arm
D (x1)
Keyboard Bracket
E (x1)
Keyboard Tray Set
F (x1)
Handle
S-C (x2)
M6x16mm Screw
S-D (x2)
M6x25mm Spring
Screw
M-A (x3)
M6x50mm Screw
M-B (x3)
Concrete Anchor
S-E (x1)
M6 Washer
S-F (x2)
M4 Washer
G (x1)
Wall Plate Cover
H (x2)
Cap
I (x5)
Velcro Pad
T-A (x1)
3mm Allen Wrench
T-B (x1)
4mm Allen Wrench
T-C (x1)
5mm Allen Wrench T-D (x1)
Level
TOOLS NEEDED
J (x1)
Connecting Plate
4
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Stud Installation
Place Wall Plate (A) against the wall and mark drilling locations with a pencil. Use of a stud
finder and Level (T-D) is highly recommended. Drill 1.2” (30mm) deep holes using a .12”
(3mm) bit, then attach Wall Plate (A) to wall using M6x50mm Screws (M-A) and a Phillips
screwdriver. Assemble Wall Plate Covers (H) to Wall Plate (A).
OPTION B: Concrete/Brick
Place Wall Plate (A) against the wall and mark drilling locations with a pencil. Use of a
Level (T-D) is highly recommended. Drill 2” (50mm) deep holes using a .31” (8mm) bit,
press Concrete Anchors (M-B) into holes, then attach Wall Plate (A) to wall using M6x50mm
Screws (M-A) and a Phillips screwdriver. Assemble Wall Plate Covers (G) to Wall Plate (A).
3mm
30mm(1.2 )
(0.12 )
8mm
50mm(2.0 )
(0.31 )
A
T-D
M-A
M-A
T-D
M-B
A
G
G
5
STEP 2
Slide Arm Extension (B) onto Wall Plate (A). Secure using M6x25mm Spring Screw (S-D)
and Cap (H) with a Phillips screwdriver.
Place Arm (C) onto Arm Extension (B). Secure using M6x25mm Spring Screw (S-D),
Cap (H), and a Phillips screwdriver.
B
A
H
S-D
C
B
H
S-D
6
STEP 3
The Keyboard Bracket (D) features a tilt adjustment allowing you to use the full tilt range
or limit the range, with a Tilt Screw (D1) under the bracket. Take note of the two positions
below and then use 3mm Allen Wrench (T-A) to adjust the Tilt Screw (D1) so that it’s in the
limited range setting. This will aide in installing the Keyboard Tray in the next step.
D
T-A
D1
D1
Full Tilt Range Limited Tilt Range
Tilt Screw is fully recessed Tilt Screw is protruding
7
STEP 4
Assemble Keyboard Tray Set (E) to Keyboard Bracket (D) and Connecting Plate (J) using
M5x10mm Screws (S-A) and a Phillips Screwdriver.
STEP 5
Attach Handle (F) to Keyboard Tray Set (E) using M4x6mm Screws (S-B) and a Phillips
screwdriver.
S-A
E
J
D
F
NOTE: Ensure the lip on Keyboard Tray Set (E) is facing up in the back and the
handle mounting holes are in the front. Also ensure that the lips on Connecting
Plate (J) are facing downward.
8
STEP 6
Attach Keyboard Bracket (D) to Arm (C) using M6x16mm Screws (S-C), M6 Washer (S-E),
and 4mm Allen Wrench (T-B).
STEP 7
Attach the Lever (C1) from Arm (C) to Keyboard Tray (E) using M4x6mm Screws (S-B), M4
Washers (S-F), and a Phillips screwdriver.
T-B
CD
S-C
S-E
C
E
C1
S-B
S-F
9
STEP 8
To set the tilt range, adjust the Tilt Screw (D1) on Keyboard Bracket (D) using 3mm
Allen Wrench (T-A). When the Screw is protruding out, the keyboard tray has a limited
range of tilt. The tray has full range of motion when the Screw is fully recessed into the
Bracket.
Full Tilt Range
Tilt Screw is fully recessed
Limited Tilt Range
D1 T-A
D
Tilt Screw is protruding
10
STEP 9
Use 3mm Allen Wrench (T-A) to adjust the arm swivel points. Press and hold the Lever (C1)
to adjust the height of the keyboard. Remove protective film from Velcro Pads (I) and apply
to top of Keyboard Tray (E) to keep keyboard from slipping.
T-A
C1
Tabla de contenidos
Otros manuales de Rack y soporte de Vivo
Vivo
Vivo MOUNT-KB04C Manual de usuario
Vivo
Vivo STAND-TV65B Manual de usuario
Vivo
Vivo STAND-V001O Manual de usuario
Vivo
Vivo STAND-V100H Manual de usuario
Vivo
Vivo DESK-V000V Series Manual de usuario
Vivo
Vivo STAND-V102AF Manual de usuario
Vivo
Vivo STAND-V000U Manual de usuario
Vivo
Vivo STAND-TV00L Manual de usuario
Vivo
Vivo MOUNT-CAR01 Manual de usuario
Vivo
Vivo STAND-TV65A Manual de usuario
Vivo
Vivo STAND-V103C Manual de usuario
Vivo
Vivo MOUNT-PC06L Manual de usuario
Vivo
Vivo STAND-E-102B Manual de usuario
Vivo
Vivo STAND-SP02B Manual de usuario
Vivo
Vivo MOUNT-V001GLW Manual de usuario
Vivo
Vivo STAND-V101C Manual de usuario
Vivo
Vivo MOUNT-HP04 Manual de usuario
Vivo
Vivo MOUNT-V00MIC Manual de usuario
Vivo
Vivo MOUNT-POLE01 Manual de usuario
Vivo
Vivo STAND-V100W Manual de usuario
