Vinotemp VT-15PR28 Manual de usuario

WWW.VINOTEMP.CO M

A PROUD HERITAGE OF EXPERIENCE & QUALITY

OVERLAY PANEL INSTALLATION INSTRUCTIONS

W i n e Coole r

VT-15PR28/VT-18PR28/VT-24PR46

WWW.VINOTEMP.CO M

INSTALLATION

•Remove all packing material before using your appliance.

•IMPORTANT: Before connecting the unit to a power source, let it stand upright for

approximately 24 hours. This will reduce the possibility of a malfunction in the cooling

system from handling during transportation.

•Clean the interior surface with lukewarm water and a soft cloth.

•This unit is designed for freestanding or built in installation and indoor or outdoor use.

Position the unit in a dry and well-ventilated place. Avoid placing the unit near any source

of heat or moisture, or in direct sunlight. Do NOT install the unit in a location with an

ambient temperature that will fall below 44°F or above 90°F.

•For built-in installation, it is a must to keep ” space on each side and at the top plus 1-2”

of space at the back to ensure proper service access and ventilation. The air vent at the

front of the appliance must never be covered or blocked in any way.

•Place the unit on a level surface strong enough to support it when it is fully loaded. To

levelthe appliance, adjust the front leveling legs at the bottom of the appliance.

•For best performance it is recommended that you install the appliance in a location with

an ambient temperature between 44-90°F. If the ambient temperature is above or below

recommended temperatures, the performance of the unit may be affected.

OVERLAY PANEL INSTALLATION INSTRUCTION

Door Panel Preparation

Depending on the wine cellar model prepare the overlay panel to the dimensions shown

below. Then attach the handle to the overlay panel by using the flat head screws and drive

the screws flush with the panel.

376 mm

VT-15PR28

732 South Racetrack Road, Henderson, Nevada 89015

i n f o @ v i not e m p . c o m

444.5 mm VT-18PR28

VT-24PR46

594.4 mm

WWW.VINOTEMP.CO M

NOTE:

1. Weight of the overlay panel should not exceed 20 pounds (9.1 kilograms).

2. It is important to ensure that all drilled holes are drilled tothe correct depth in

order to avoid splits in the wood when hardware is installed.

3. Drill the handle installation holes in the overlay panel according tothe handle you

are planning to use. If reusing the handles came with the unit, drill two holes

with holes distance 707mm (27-53/64”) and diameter 5mm (3/16”) in the

overlay panel.

Door Panel Installation

1. Remove the bottom hinge assembly (2) by unscrewing the four lock screws (1). Be

careful to hold the door (4) firmly after removing the screws. (Fig. 1)

2. Gently pull down to remove the door from the right top hinge and place it on a padded

surface to avoid the risk of damage. (Fig. 2)

3. Remove door gasket (9) completely from door (4). Start in a corner and pull outward.

This may take some force. Set gasket down on a flat surface for later installation.

4. Remove the door adapters (6) and hinge sleeves (7) by unscrewing the screws (8).

5. Attach the wood overlay panel (3) to the door face by using 8 wood screws #10x1.5

(ST4x40) Type AB Philips (5).

6. Repeat steps described above in reverse to replace the door adapters (6), hinge sleeves

(7) and gasket (9).

7. Relocate the finished door to the designated position. Then screw the bottom hinge

assembly and tighten it after the door is leveled.

34 5 678

i n f o @ v i not e m p . c o m

REVERSING THE DOOR SWING OF YOUR APPLIANCE

This unit has the capability of the door opening from either the left or right side. The unit is

delivered to you with the door opening from the left side. Should you desire to reverse the

opening direction, please follow the reversal instructions shown below.

NOTE: All partsremoved must be saved to allow the door swing to be reversed.

1. Remove the bottom hinge (2) by unscrewing the four lock screws (1). Be careful to hold

the door firmly after removing the screws. (Fig. 1)

2. Gently pull down to remove the door from the right top hinge and place it on a padded

surface to avoid the risk of damage. Then remove the right top hinge (4). (Fig. 3)

3. Unscrew and transfer pin (3) of the hinge plate to the opposite side. (Fig. 2)

4. Pop out the cover caps on the left side of the cabinet and use them to cover the screw

holes on the right hand side.

5. Screw the alternative left top hinge (6), included in the fittings, on the left hand side of the

cabinet. (Fig. 3)

6. Rotate the door 180° and relocate it to the designated position. Then screw the bottom

hinge assembly on the left designated position and tighten it after the door is leveled. (Fig.

732 South Racetrack Road, Henderson, Nevada 89015

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enfriador de vino de Vinotemp

Vinotemp

Vinotemp 4500DS Manual de usuario

Vinotemp

Vinotemp VT-188 Manual de usuario

Vinotemp

Vinotemp WINE-MATE WM-1500HTD Instrucciones de uso

Vinotemp

Vinotemp 1500SSW Manual de usuario

Vinotemp

Vinotemp Wine-Mate WM-1500SSL Manual de usuario

Vinotemp

Vinotemp Wine-Temp WM-6500HZD-DE Instrucciones de uso

Vinotemp

Vinotemp WINE-MATE VINO-2500SSR Manual de usuario

Vinotemp

Vinotemp element EL-18TEDCS Manual de usuario

Vinotemp

Vinotemp WINE-MATE VINO3500HZD Manual de usuario

Vinotemp

Vinotemp VT-WC58GNV-SB10 Manual de usuario

Vinotemp

Vinotemp 2500SSR Manual de usuario

Vinotemp

Vinotemp Wine-Mate WM-2500SSD Manual de usuario

Vinotemp

Vinotemp Wine-Mate WM-2520SSV-LA Guía de instalación

Vinotemp

Vinotemp VT-8WC-OP Manual de usuario

Vinotemp

Vinotemp 700 Manual de usuario

Vinotemp

Vinotemp VT-15 TS Manual de usuario

Vinotemp

Vinotemp IL Romanzo IL-OW006-2Z Manual de usuario

Vinotemp

Vinotemp Wine-Mate WM-1500CD Instrucciones de uso

Vinotemp

Vinotemp VT-34-2ZONE Manual de usuario

Vinotemp

Vinotemp IL-OW002 Manual de usuario

Vinotemp

Vinotemp Wine-Mate WM-2500SSD Manual de usuario

Vinotemp

Vinotemp VT-CAVA2D Manual de usuario

Vinotemp

Vinotemp VT-15 TS Manual de usuario

Vinotemp

Vinotemp VT-6TEDS Manual de usuario

Manuales populares de Enfriador de vino de otras marcas

U-Line

U-Line Echelon Wine Captain 2075WC Manual del propietario

Haier

Haier WS50GA Manual de usuario

Cavist

Cavist 62 Manual de usuario

Kenmore

Kenmore 461.99130 Manual de usuario

Miele

Miele KWT 6422 iG Manual de usuario

Danby

Danby DWC113BLSDB Manual de usuario

Caple

Caple Wi6128 Manual de usuario

Avanti

Avanti WC1001 Manual de usuario

Frigidaire

Frigidaire FFWC38F6LS Manual de usuario

Titan

Titan TT-W2454SZ Manual de instalación

Klarstein

Klarstein Botella 166 Uno Manual de usuario

Costway

Costway FP10130WL Manual de usuario

Lemair

Lemair LWC59 Manual de usuario

Haier

Haier JC-125GEA Manual de usuario

Caple

Caple WCi46B Manual de usuario

Climadiff

Climadiff CLI24 Guía rápida

Viking

Viking VCWB301LSS Manual de usuario

Caple

Caple WC6511 Manual de usuario