Viessmann VITOSOLIC 200 Manual de usuario

Operating instructions

for the system user

VIESMANN

Control unit for solar thermal systems

VITOSOLIC 200

5592 613 GB 5/2009 Please keep safe.

Please follow these safety instructions closely to prevent accidents and mate-

rial losses.

Safety instructions explained

Danger

This symbol warns against the

risk of injury.

!Please note

This symbol warns against the

risk of material losses and envi-

ronmental pollution.

Note

Details identified by the word "Note" con-

tain additional information.

Target group

These operating instructions are

designed for system users.

This appliance is not designed to be

used by persons (including children) with

limited physical, sensory or mental

capacities, or lacking experience and/or

knowledge, unless they are supervised

by a person responsible for their safety,

or have received instructions from such

a person as to how to use the appli-

ance.

!Please note

Children should be supervised.

Ensure that children never play

with the appliance.

Danger

Incorrect work on the system can

lead to life-threatening acci-

dents.

Work on electrical equipment

must only be carried out by a

qualified electrician.

In case of fire

Danger

Fire creates the risk of burning

and explosions.

■ Shut down the system.

■ Use a tested fire extinguisher,

class ABC.

Ancillary components, spare and

wearing parts

!Please note

Components that are not tested

with the system may lead to sys-

tem damage, or may affect its

functions.

Installation or replacement work

must only be carried out by quali-

fied personnel.

Safety instructions

For your safety

5592 613 GB

Introductory information

Commissioning..................................................................................................... 4

Operation............................................................................................................ 5

Scanning options

Scanning actual values........................................................................................ 6

Scanning messages............................................................................................. 7

Scanning statement values.................................................................................. 8

Scanning the heat meter...................................................................................... 8

What to do if...

The solar thermal system does not start.............................................................. 10

There is no DHW available................................................................................... 10

The display appears dark..................................................................................... 11

The display illumination flashes............................................................................ 11

Scanning faults..................................................................................................... 11

Menu overview.................................................................................................... 12

Index

5592 613 GB

The commissioning and matching up of

the control unit to local conditions and to

the structural characteristics of the build-

ing, plus the instruction of the user in

operating the system, must be carried

out by your heating contractor.

Introductory information

Commissioning

5592 613 GB

Controls

30.04.2009

Tcol

Tcylb

10:59

47.7 °C

35.4 °C

AStandard display

The standard display will automat-

ically show after approx. 4 min.

BOK key; to confirm your selection

or save the setting.

This takes you to the previous

step in the menu or cancels a set-

ting that has been started.

/ Cursor keys

To scroll through the menu.

/ Cursor keys

To adjust values.

To change between standard dis-

play and main menu.

The display can show four lines at a time.

The arrow on the l.h. side of the display

highlights the available menu item.

You can scroll through the menu with the

/ keys.

Operation

5592 613 GB

Press the following keys:

1. for the "Main menu".

2. OK the first three actual values will

be displayed.

3. / for additional actual values,

subject to the system equip-

ment level.

4. until the "Main menu"

appears.

"Actual values" Explanation

Tcol Collector temperature in °C

Tcol2 Collector temperature in an additional collector array in °C

Tcylb Actual cylinder temperature in °C

Tcyl2b to Tcyl4b Actual cylinder temperature for additional consumers (e.g.

DHW cylinder 2) in °C

Tby Bypass temperature in °C

T-HE Temperature in an external heat exchanger in °C

Cyl. add. Auxiliary function for DHW heating

Time

Date

Relays 1 to 7 Relay condition

Sensors 1 to 12 Temperature at the respective sensor in °C

Note

If the sensor inputs are not connected, the value for "lead

break" will be displayed.

Intens. Radiation intensity in conjunction with a solar thermal sys-

tem

Note

If the sensor inputs are not connected, the value for "lead

break" will be displayed.

A diagram in the standard display ena-

bles you to scan the collector and actual

cylinder temperatures in the course of

the day. In addition, if your heating con-

tractor has enabled the heat meter, a

diagram displays the heat volume for the

past seven days.

Press the key in succession; the fol-

lowing diagrams will be displayed:

Scanning options

Scanning actual values

5592 613 GB

Actual cylinder temperature curve

Tcylb today

Collector temperature curve

Tcol today

Amount of heat in kWh

HM 1

5 5

Note

The right bar indicates the value of the

current day in kWh.

Scanning messages

Press the following keys:

1. for the "Main menu".

2. for "Reports".

3. OK to confirm.

4. for further displays (see the fol-

lowing table).

"Messages:" Explanation

No fault There is no fault at the solar control unit.

Loading cyl...

(only with several consum-

ers)

Consumer displayed is being heated.

Pause cyl...

(only with several consum-

ers)

Only if the "Cyclical heating" function has been ena-

bled by your heating contractor:

Pause in the heating of the displayed consumer.

Cyl set... Consumer displayed has reached its set value.

Fault A fault has occurred at the solar control unit (for "Scan-

ning the fault display", see page 11).

SW version Software version (only for service engineers)

HW version Hardware version (only for service engineers)

Scanning options

Scanning actual values (cont.)

5592 613 GB

Press the following keys:

1. for the "Main menu".

2. for "Solar".

3. OK to confirm.

4. for "Statement".

5. OK to confirm.

6. / for additional statement val-

ues, subject to the system

equipment level.

7. until the "Main menu"

appears.

"Statement" Explanation

Colmax Maximum collector temperature in °C

Col2max Maximum collector temperature in an additional collector

array in °C

Cylmax Maximum cylinder temperature in °C

Cly2max to

Cly4max

Maximum cylinder temperature for additional consumers (e.g.

DHW cylinder 2) in °C

Relays 1 to 7 Hours run of actuators connected at relay outputs (e.g. solar

circuit pump at R1)

Days Days run, solar control unit

To reset the values, except for days

run:

Whilst the value is displayed, press the

following keys:

1. OK "Delete?""Yes" is displayed.

2. OK to confirm.

Scanning the heat meter

Press the following keys:

1. for the "Main menu".

2. for "HM".

3. OK to confirm.

4. for "HM 1" or "HM 2".

5. OK to confirm.

6. / for additional values, subject to

the system equipment level.

Scanning options

Scanning statement values

5592 613 GB

7. until the "Main menu"

appears.

"HM..." Explanation

Tflow Flow temperature in °C

Tretn Return temperature in ºC

"Heat" Amount of heat in Wh

"Heat" Amount of heat in kWh

"Heat" Amount of heat in MWh

Note

Add the heat values together.

The values are not calibrated.

To reset the heat meter values:

Whilst the value is displayed, press the

following keys:

1. OK "Delete?""Yes" is displayed.

2. OK to confirm.

Scanning options

Scanning the heat meter (cont.)

5592 613 GB

Cause Remedy

The mains isolator is switched OFF. Switch ON the mains isolator.

The solar control unit MCB has respon-

ded (mains voltage is present, display

does not illuminate).

Contact your local heating contractor.

Collector limit temperature or set cylinder

temperature has been reached.

Wait until the respective temperature has

fallen below the relevant limit.

The solar control unit is in "manual

mode".

To select "Auto":

1. Press .

2. Press until "Manual mode" is dis-

played.

3. Press OK to confirm.

4. Press until "Relay 1" etc. is dis-

played.

5. Press OK to confirm.

6. Press the / keys for "Auto".

7. Press OK to confirm.

8. Press until "Main menu" is dis-

played.

There is no DHW available

Cause Remedy

The solar control unit is faulty. Contact your local heating contractor.

Collector temperature too high; safety

shutdown through the solar control unit.

Wait until the collector temperature has

fallen.

The set cylinder temperature is too low. Contact your local heating contractor.

Solar circuit pump faulty. Contact your local heating contractor.

The DHW cylinder is not reheated:

The operating and time program is incor-

rectly set at the boiler control unit.

Enable DHW heating.

Operating instructions of the boiler

control unit

What to do if...

The solar thermal system does not start

5592 613 GB

Otros manuales para VITOSOLIC 200

Tabla de contenidos

Otros manuales de Unidad de control de Viessmann

Viessmann

Viessmann 5214 Manual de usuario

Viessmann

Viessmann VITOSOLIC 200 Instrucciones de funcionamiento

Viessmann

Viessmann VITOTRONIC 100 Instrucciones de funcionamiento

Viessmann

Viessmann 5547 Manual de usuario

Viessmann

Viessmann VITOTRONIC SPS Instrucciones de funcionamiento

Viessmann

Viessmann VITOSOLIC 100 Instrucciones de funcionamiento

Viessmann

Viessmann 5574 Manual de usuario

Viessmann

Viessmann Vitotronic 100 HC1 Manual

Viessmann

Viessmann 5221 Manual de usuario

Viessmann

Viessmann VITOTRONIC 200 Instrucciones de funcionamiento

Viessmann

Viessmann Vitotronic 100 GC1 Guía rápida

Viessmann

Viessmann 5205 Manual de usuario

Viessmann

Viessmann 5215 2A Manual de usuario

Viessmann

Viessmann VITOTRONIC 100 Guía rápida

Viessmann

Viessmann 5224 Manual de usuario

Viessmann

Viessmann EM-EA1 extension Guía rápida

Viessmann

Viessmann VITOTRONIC 300-K Guía rápida

Viessmann

Viessmann 5222 Manual de usuario

Viessmann

Viessmann vitotronic 200-h Manual de usuario

Viessmann

Viessmann PLC VITOCAL 350-HT PRO Instrucciones de funcionamiento

Viessmann

Viessmann VITOSOLIC 100 Guía rápida

Viessmann

Viessmann Cascade control unit Manual de servicio

Viessmann

Viessmann SM1 Guía rápida

Viessmann

Viessmann LANZ Bulldog Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario