Viessmann VITORADIAL 300-T Instrucciones de funcionamiento
Service instructions
for contractors
VIESMANN
Vitoradial 300-T
Type VR3, 101 to 335 kW
Condensing boiler with heat exchanger
For applicability, see the last page
VITORADIAL 300-T
5692 820 GB 3/2013 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively inten-
ded for qualified contractors.
■ Work on gas installations must only be
carried out by a registered gas fitter.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system:
■ Statutory regulations regarding the
prevention of accidents
■ Statutory regulations regarding envi-
ronmental protection
■ Codes of practice of the relevant trade
associations
■ All current safety regulations as
defined by DIN, EN, DVGW, TRGI,
TRF, VDE and all locally applicable
standards
■ Gas Safety (Installation & Use) Regu-
lations
– the appropriate Building Regulation
either the Building regulations, the
Building Regulation (Scotland), Build-
ing Regulations (Northern Ireland),
– the Water Fittings Regulation or
Water Bylaws in Scotland,
– the current I.E.E. Wiring Regula-
tions.
If you smell gas
Danger
Escaping gas can lead to explo-
sions which may result in serious
injury.
■ Do not smoke. Prevent naked
flames and sparks. Do not
switch lights or electrical appli-
ances on or off.
■ Close the gas shut-off valve.
■ Open windows and doors.
■ Evacuate any people from the
danger zone.
■ Notify your gas or electricity
supply utility from outside the
building.
■ Shut off the electricity supply to
the building from a safe place
(outside the building).
Safety instructions
Safety instructions
5692 820 GB
3
If you smell flue gas
Danger
Flue gas can lead to life-threat-
ening poisoning.
■ Shut down the heating system.
■ Ventilate the installation site.
■ Close all doors in the living
space.
Flue systems and combustion air
Ensure that flue systems are clear and
cannot be sealed, for instance due to
accumulation of condensate or other
causes. Ensure a sufficient supply of
combustion air.
Instruct system users that subsequent
modifications to the building characteris-
tics are not permissible (e.g. cable/pipe-
work routing, cladding or partitions).
Danger
Life-threatening poisoning
caused by carbon monoxide in
the flue gas occurs as a result of
leaking or blocked flue systems
or an insufficient supply of com-
bustion air.
Ensure the flue system is in
proper working order. It must not
be possible to close apertures for
interconnected combustion air
supply.
Extractors
Operating appliances that extract air to
the outside (cooker hoods, extractors, air
conditioning units, etc.) can create neg-
ative pressure. If the boiler is operated at
the same time, this can lead to reverse
flow of the flue gas.
Danger
The simultaneous operation of
the boiler and appliances that
extract air to the outside can
result in life threatening poison-
ing due to reverse flow of the flue
gas.
Fit an interlock circuit or take suit-
able steps to ensure a sufficient
supply of combustion air.
Working on the system
■ Where gas is used as the fuel, close
the main gas shut-off valve and safe-
guard it against unintentional reopen-
ing.
■ Isolate the system from the power sup-
ply (e.g. by removing the separate fuse
or by means of a mains isolator) and
check that it is no longer 'live'.
■ Safeguard the system against recon-
nection.
!Please note
Electronic assemblies can be
damaged by electrostatic dis-
charge.
Prior to commencing any work,
touch earthed objects, such as
heating or water pipes to dis-
charge static loads.
Repair work
!Please note
Repairing components that fulfil a
safety function can compromise
the safe operation of your sys-
tem.
Defective components must be
replaced with genuine
Viessmann spare parts.
Safety instructions
Safety instructions (cont.)
5692 820 GB
4
Auxiliary components, spare and
wearing parts
!Please note
Spare and wearing parts that
have not been tested together
with the system can compromise
its function. Installing non-author-
ised components and making
non-approved modifications or
conversions can compromise
safety and may invalidate our
warranty.
For replacements, use only orig-
inal spare parts supplied or
approved by Viessmann.
Safety instructions
Safety instructions (cont.)
5692 820 GB
5
Product information
Intended use......................................................................................................... 6
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance.......................................... 7
Further details regarding the individual steps....................................................... 9
Parts lists
Parts list, boiler..................................................................................................... 27
Parts list, heat exchanger..................................................................................... 30
Water quality
Water quality requirements.................................................................................. 33
Commissioning/service reports........................................................................ 37
Specification....................................................................................................... 38
Certificates
Declaration of conformity...................................................................................... 39
Manufacturer's certificate according to the 1st BImSchV [Germany]................... 40
Keyword index.................................................................................................... 41
Index
Index
5692 820 GB
6
The appliance is only intended to be
installed and operated in sealed unven-
ted heating systems that comply with
EN 12828, with due attention paid to the
associated installation, service and
operating instructions as well as the
details in the datasheet.
It is only designed for the heating up of
heating water.
Commercial or industrial usage for a pur-
pose other than the heating up of heating
water shall be deemed inappropriate.
Intended use presupposes that a fixed
installation in conjunction with permissi-
ble components designed for this pur-
pose has been carried out.
Every other use will be deemed to be
inappropriate. Any resulting losses are
excluded from the manufacturer's liabil-
ity.
Any usage beyond this must be
approved by the manufacturer for the
individual case.
Intended use also includes the adher-
ence to maintenance and inspection
intervals.
Product information
Intended use
5692 820 GB
7
For further information regarding the individual steps, see the page indicated
Commissioning steps
Inspection steps
Maintenance steps Page
•1. Matching the settings of the boiler control unit.......... 9
•2. Checking the connections of the neutralising system
and filling with neutralising agent
••• 3. Commissioning the system........................................... 9
•4. Checking the burner adjustment................................... 10
• • 5. Shutting down the system............................................. 11
• • 6. Opening the boiler door................................................. 11
•7. Cleaning the internal pipes and heating surface......... 12
••• 8. Checking all gaskets and packing cords on the flue
gas side
• • 9. Checking the thermal insulation components on the
boiler door
•10. Inserting the internal pipes............................................ 13
• • 11. Fitting the boiler door..................................................... 14
••• 12. Checking connections and sensor well for leaks on
the heating water side
••• 13. Checking the function of the safety equipment........... 15
••• 14. Checking the expansion vessel and system pressure 15
••• 15. Checking the firm seating of electrical plug-in
connections and cable grommets
••• 16. Checking the heat exchanger gasket........................... 17
• • 17. Cleaning the flue outlet and heat exchanger............... 21
• • 18. Checking the water quality............................................ 22
• • 19. Checking the neutralising system as per the
manufacturer's instructions and replacing used
neutralising agent
• • 20. Cleaning the sight glass in the boiler door.................. 24
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance
5692 820 GB
8
Commissioning steps
Inspection steps
Maintenance steps Page
••• 21. Checking the mixer for ease of operation and
tightness.......................................................................... 24
••• 22. Checking the function of the return temperature
raising facility (if installed)
••• 23. Checking the installation room ventilation
••• 24. Checking the flue pipe and all connections from the
heat exchanger to the flue system for tightness
• • 25. Restarting the system
• • 26. Adjusting the burner...................................................... 25
•27. Instructing the system user........................................... 26
•28. Operating and service instructions.............................. 26
Commissioning, inspection, maintenance
Steps - commissioning, inspection and… (cont.)
5692 820 GB
9
Matching the settings of the boiler control unit
Make the settings according to the infor-
mation in chapter "Additional informa-
tion, coding" in the control unit service
instructions.
Commissioning the system
Operating and service instruc-
tions for the control unit and the
burner
01. Check that the internal pipes are
fully pushed into the hot gas flues
(see chapter "Inserting the internal
pipes"); open the boiler door for
this.
02. Check that the installation room
vent is open.
03. Fill the heating system with water
and vent the system.
Permissible operating pressure:
4 bar (0.4 MPa)
!Please note
Scaling may result if the sys-
tem is not operated with fully
softened heating water.
Operate boilers only with
softened water.
Observe the instructions in
chapter "Water quality
requirements".
04. Enter the amount of fill water and
water hardness into the table in
chapter "Checking the water qual-
ity".
05. Check the system pressure.
06. Check the oil level or the gas supply
pressure.
07. Open the flue gas damper (if instal-
led).
08. Check that the cleaning aperture on
the flue outlet is closed.
09. Open the shut-off valves in the oil or
gas line.
10. Switch ON the mains isolator, the
switch for the heating circuit pump
and the burner ON/OFF switch in
this order (observe the burner man-
ufacturer's instructions).
Commissioning, inspection, maintenance
Further details regarding the individual steps
5692 820 GB
10
11. When heating the system from cold
(also when restarting after mainte-
nance and cleaning work), prevent
all heat supply to heat consumers,
in order to clear the dew point range
as quickly as possible.
!Please note
During boiler heat-up,
unpleasant fumes and
odours can result from out-
gassing from the thermal
insulation, the heating block
and the paint.
Vent the room during com-
missioning.
12. After the flow temperature has been
reached, switch ON the heat con-
sumers in sequence and change the
burner over to automatic mode.
!Please note
When testing the flue gas for
CO, internal gases being
expelled from the heating
block can cause higher val-
ues.
Continue to operate the
boiler until a clear decline
can be recognised.
13. Check all gaskets and plugs, and
retighten if necessary.
14. Check the boiler door and cleaning
cover after approx. 50 hours run and
retighten all screws.
Danger
Opening the connections on the
heating water side whilst the
boiler is under pressure can
result in injuries.
First depressurise the boiler.
Only drain the boiler with a suc-
tion pump if the air vent valve is
open.
Checking the burner adjustment
Burner service instructions
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 820 GB
Otros manuales para VITORADIAL 300-T
3
Tabla de contenidos
Otros manuales de Caldera de Viessmann
Viessmann
Viessmann Vitodens 222-F Guía rápida
Viessmann
Viessmann Vitodens 100-W WB1B Series Manual de usuario
Viessmann
Viessmann VITODENS 200 Manual de usuario
Viessmann
Viessmann VITODENS 050-W Manual de usuario
Viessmann
Viessmann Vitocrossal 200 CM2 Series Guía de inicio rápido
Viessmann
Viessmann VITOCONTROL-S, WB2B Manual de usuario
Viessmann
Viessmann KRT 150 series Manual de usuario
Viessmann
Viessmann Vitoflex RF 150 Guía rápida
Viessmann
Viessmann VITOCROSSAL 200 Instrucciones de funcionamiento
Viessmann
Viessmann VITOROND 200 VD2A-125 Manual de usuario
Viessmann
Viessmann VITOPEND 222 WHSA Manual de usuario
Viessmann
Viessmann Vitomax HW Series Manual de capacitación
Viessmann
Viessmann CombiPLUS Kit Hoja de datos
Viessmann
Viessmann VITOPLEX 100 Instrucciones de funcionamiento
Viessmann
Viessmann Flue gas system Manual de usuario
Viessmann
Viessmann Vitomax HW Series Manual de usuario
Viessmann
Viessmann Vitodens 100-W Manual de usuario
Viessmann
Viessmann VITOPLEX 100 Instrucciones de funcionamiento
Viessmann
Viessmann VITOCROSSAL 300 Instrucciones de funcionamiento
Viessmann
Viessmann VITOTRONIC 300 GW2 Guía
