Viessmann VITOCROSSAL 300 Instrucciones de funcionamiento
Service instructions
for contractors
VIESMANN
Vitocrossal 300
Type CR3B, 787 to 1400 kW
Gas condensing boiler
For applicability, see the last page
VITOCROSSAL 300
5692 910 GB 11/2013 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively inten-
ded for qualified contractors.
■ Work on gas installations must only be
carried out by a registered gas fitter.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system:
■ Statutory regulations regarding the
prevention of accidents
■ Statutory regulations regarding envi-
ronmental protection
■ The Code of Practice of relevant trade
associations
■ All current safety regulations as
defined by DIN, EN, DVGW, TRGI,
TRF, VDE and all locally applicable
standards
aÖNORM, EN, ÖVGW-TR Gas,
ÖVGW-TRF and ÖVE
cSEV, SUVA, SVGW, SVTI,
SWKI, VKF and EKAS guideline
1942: LPG, part 2
If you smell gas
Danger
Escaping gas can lead to explo-
sions which may result in serious
injury.
■ Do not smoke. Prevent naked
flames and sparks. Do not
switch lights or electrical appli-
ances on or off.
■ Close the gas shut-off valve.
■ Open windows and doors.
■ Evacuate any people from the
danger zone.
■ Notify your gas or electricity
supplier and your local heating
contractor from outside the
building.
■ Shut off the electricity supply to
the building from a safe place
(outside the building).
Safety instructions
Safety instructions
5692 910 GB
3
If you smell flue gas
Danger
Flue gas can lead to life threat-
ening poisoning.
■ Shut down the heating system.
■ Ventilate the installation site.
■ Close all doors in the living
space.
Flue systems and combustion air
Ensure that flue systems are clear and
cannot be sealed, for instance due to
accumulation of condensate or other
causes. Ensure a sufficient supply of
combustion air.
Instruct system users that subsequent
modifications to the building characteris-
tics are not permissible (e.g. cable/pipe-
work routing, cladding or partitions).
Danger
Leaking or blocked flue systems,
or an insufficient supply of com-
bustion air can cause life threat-
ening poisoning from carbon
monoxide in the flue gas.
Ensure the flue system is in
proper working order. Apertures
for supplying combustion air
must be non-closable.
Extractors
Operating appliances that extract air to
the outside (cooker hoods, extractors, air
conditioning units, etc.) can create neg-
ative pressure. If the boiler is operated at
the same time, this can lead to reverse
flow of the flue gas.
Danger
The simultaneous operation of
the boiler and appliances that
extract air to the outside can
result in life threatening poison-
ing due to reverse flow of the flue
gas.
Fit an interlock circuit or take suit-
able steps to ensure a sufficient
supply of combustion air.
Working on the system
■ Where gas is used as the fuel, close
the main gas shut-off valve and safe-
guard it against unintentional reopen-
ing.
■ Isolate the system from the power sup-
ply (e.g. by removing the separate fuse
or by means of a mains isolator) and
check that it is no longer 'live'.
■ Safeguard the system against recon-
nection.
Danger
Hot surfaces can cause burns.
■ Before maintenance or service
work, switch OFF the appli-
ance and let it cool down.
■ Never touch hot surfaces on
the boiler, burner, flue system
or pipework.
!Please note
Electronic assemblies can be
damaged by electrostatic dis-
charge.
Before beginning work, touch
earthed objects, such as heating
or water pipes, to discharge static
loads.
Safety instructions
Safety instructions (cont.)
5692 910 GB
4
Repair work
!Please note
Repairing components that fulfil a
safety function can compromise
the safe operation of the sys-
tem.
Faulty components must be
replaced with original Viessmann
spare parts.
Auxiliary components, spare and
wearing parts
!Please note
Spare and wearing parts that
have not been tested together
with the system can compromise
its function. Installing non-author-
ised components and making
non-approved modifications or
conversions can compromise
safety and may invalidate the
warranty.
For replacements, use only orig-
inal spare parts supplied or
approved by Viessmann.
Safety instructions
Safety instructions (cont.)
5692 910 GB
5
Product information
Intended use......................................................................................................... 6
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance.......................................... 7
Further details regarding the individual steps....................................................... 9
Parts lists............................................................................................................ 23
Commissioning/service reports
Reports..................................................................................................................... 30
Specification....................................................................................................... 31
Water quality
Water quality requirements.................................................................................. 32
Certificates
Declaration of Conformity..................................................................................... 36
Certificates
Manufacturer's certificate according to the 1st BImSchV..................................... 37
Keyword index.................................................................................................... 38
Index
Index
5692 910 GB
6
The appliance is only intended to be
installed and operated in sealed unven-
ted heating systems that comply with
EN 12828, with due attention paid to the
associated installation, service and
operating instructions as well as the
details in the datasheet.
It is only designed for the heating up of
heating water.
Commercial or industrial usage for a pur-
pose other than the heating up of heating
water shall be deemed inappropriate.
Intended use presupposes that a fixed
installation in conjunction with permissi-
ble components designed for this pur-
pose has been carried out.
Every other use will be deemed to be
inappropriate. Any resulting losses are
excluded from the manufacturer's liabil-
ity.
Any usage beyond this must be
approved by the manufacturer for the
individual case.
Intended use also includes the adher-
ence to maintenance and inspection
intervals.
Product information
Intended use
5692 910 GB
7
For further information regarding the individual steps, see the page indicated
Commissioning steps
Inspection steps
Maintenance steps Page
•1. Checking the high limit safety cut-out setting............. 9
•2. Filling the heating system with water and venting...... 9
•3. Fully opening the rotary damper in the flue outlet and
securing it........................................................................ 9
••• 4. Commissioning the system........................................... 9
•5. Minimising pulsation noise............................................ 10
• • 6. Shutting down the system............................................. 11
• • 7. Opening the boiler door................................................. 11
• • 8. Separating the neutralising system from the heat
exchanger module and connecting the drain hose..... 12
• • 9. Cleaning the combustion chamber and heating
surfaces........................................................................... 12
• • 10. Checking gaskets and thermal insulation
components.................................................................... 13
• • 11. Checking all connections and the sensor well on the
heating water side for tightness.................................... 15
• • 12. Checking the function of the safety equipment........... 16
••• 13. Expansion vessel and system pressure ...................... 16
•14. Cleaning the sight glass in the boiler door.................. 18
• • 15. Closing the boiler door.................................................. 18
•16. Checking the thermal insulation................................... 18
• • 17. Checking the water quality............................................ 18
• • 18. Cleaning and reconnecting the condensate drain
system............................................................................. 19
•19. Checking the installation room ventilation
•20. Checking the flue system for tightness
• • 21. Adjusting the burner...................................................... 20
Commissioning, inspection, maintenance
Steps - commissioning, inspection and maintenance
5692 910 GB
8
Commissioning steps
Inspection steps
Maintenance steps Page
• • 22. Checking the flue gas side for tightness...................... 21
•23. Instructing the system user........................................... 22
•24. Operating and service documents................................ 22
Commissioning, inspection, maintenance
Steps - commissioning, inspection and… (cont.)
5692 910 GB
9
Checking the high limit safety cut-out setting
The high limit safety cut-out must not be
set higher than 110 °C; if required, set it
to a maximum of 110 °C.
Control unit installation and serv-
ice instructions
Filling the heating system with water and venting
Record the charge volume, water hard-
ness and pH value on page 19.
Permissible boiler operating pressure:
6 bar (0.6 MPa).
!Please note
Unsuitable water quality can
result in damage to the boiler
shell and the heating system.
Fill the heating system with water
and operate it in accordance with
VDI Guideline 2035. The total of
alkaline earths must not exceed
0.02 mol/m3 (total hardness
0.11 °dH).
Observe the "Water quality
requirements" on page 32.
Fully opening the rotary damper in the flue outlet and securing
it
The rotary damper must be in the hori-
zontal position.
Note
For handling the rotary damper, see
"Minimising pulsation noise" on
page 10.
Commissioning the system
Operating instructions for control
unit, burner and neutralising sys-
tem, service instructions for con-
trol unit, and burner manufactur-
er's documentation
1. Check the heating system pressure.
Permissible boiler operating pres-
sure: 6 bar (0.6 MPa)
2. Check that the installation room ven-
tilation is unobstructed.
3. Check the gas supply pressure.
4. Check that the cleaning aperture on
the flue outlet is closed.
5. Open the gas line shut-off valves.
Commissioning, inspection, maintenance
Further details regarding the individual steps
5692 910 GB
10
6. Start the system in this order:
1. Mains isolator
2. Switch for the heating circuit pump
3. ON/OFF switch for the burner
Burner manufacturer's oper-
ating instructions
7. Check the function of the neutralising
system.
Neutralising system operating
instructions
8. Check all gaskets and plugs, and
retighten if necessary.
Note
We recommend you check all con-
nections on the heating water side for
tightness after approx. 500 hours run
(see page 15).
9. Check the boiler door and cleaning
cover a few days after commissioning
and retighten all screws.
10. Tighten the screws at the connec-
tions with the following torque:
Boiler door 20 Nm
Flange connections 110 Nm
Module connection 60 Nm
Flue gas collector 7 Nm
Danger
For safe operation, a minimum
operating pressure of 0.5 bar
(50 kPa) is essential.
For this, a minimum pressure
switch can be used.
Minimising pulsation noise
Whatever the make of boiler, burner or
flue system, gas-tight flue systems can
still create pulsation noise. A change of
resonance may be affected by rotating
the damper fitted into the flue outlet.
Commissioning, inspection, maintenance
Further details regarding the individual steps (cont.)
5692 910 GB
Otros manuales para VITOCROSSAL 300
28
Tabla de contenidos
Otros manuales de Caldera de Viessmann
Viessmann
Viessmann VITOCROSSAL 300 Manual de usuario
Viessmann
Viessmann Vitorond 200 Series Manual de usuario
Viessmann
Viessmann Vitocrossal 300 CU3A Guía del usuario
Viessmann
Viessmann Vitodens 100 Manual de usuario
Viessmann
Viessmann ECV Series Guía rápida
Viessmann
Viessmann VITOPLEX 100?LS Manual de usuario
Viessmann
Viessmann Vitodens 200-W System Guía de inicio rápido
Viessmann
Viessmann Vitodens 200-W System Manual de usuario
Viessmann
Viessmann VITORONDENS 200-T Instrucciones de funcionamiento
Viessmann
Viessmann Vitodens 111-W Guía rápida
Viessmann
Viessmann VITOROND 200 Manual de instrucciones
Viessmann
Viessmann VITODENS 200-W B2HE 85 Manual de usuario
Viessmann
Viessmann VITOGAS 100 Guía
Viessmann
Viessmann VITODENS 200 Manual de usuario
Viessmann
Viessmann Vitodens 200-W System Manual de usuario
Viessmann
Viessmann Vitodens 100-W WB1A Series Guía
Viessmann
Viessmann Vitodens 100-W WB1B Series Guía rápida
Viessmann
Viessmann Vitocell 050-E Guía rápida
Viessmann
Viessmann VITOGAS 050 Manual de instrucciones
Viessmann
Viessmann VITOCROSSAL 300 Instrucciones de funcionamiento
