Victron energy MPPT Control Manual de usuario

www.victronenergy.com

Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands

General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40

E-mail: sales@victronenergy.com | www.victronenergy.com

Installation

Connect the MPPT Control to a BlueSolar MPPT with VE.Direct port using a VE.Direct cable.

If the MPPT Control is connected to a MPPT that shuts down at night, the MPPT Control can be connected to a battery using the

supplied cable. This way, the MPPT Control stays powered while the MPPT is off and the last received status, history and settings of

the MPPT can be viewed.

Specifications

MPPT Control

Supply voltage range

6,5 - 95 VDC (Battery powered)

5V (VE.direct powered)

Current draw, back light off

< 4 mA

Operating temperature range

-20 - +50°C (0 - 120°F)

Supported MPPTs

Models

All models with VE.Direct port, except the

BlueSolar MPPT 70/15

Software version

All software versions >= 1.12

INSTALLATION & DIMENSIONS

Installation

Flush mount

Front

63 mm diameter

Front bezel

69 x 69 mm (2.7 x 2.7 inch)

Body diameter

52mm (2.0 inch)

Body depth

31mm (1.2 inch)

ACCESSORIES

Cables (included)

cable with fuse for battery powered

operation

Buttons and display

SETUP

Cancel / back

SELECT

Select / confirm

Change item or value

On There is a connection with the MPPT.

Blinking

There was a connection with the MPPT but the connection is lost.

The last know values will be shown.

Off There has not been a connection with a MPPT.

MPPT Control

Rev 0.1

Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands

General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40

E-mail: sales@victronenergy.com | www.victronenergy.com

Menus

Status

The MPPT Control starts in the status menu. This shows the current status of the MPPT.

By pressing the up and down button, one can switch between the following values:

PANEL POWER

PANEL VOLTAGE

YIELD TODAY

CHARGER ERROR This is only visible when there is an actual error

CHARGER STATE Possible value:

OFF, FAULT, BULK, ABSORPTION, FLOAT

BATTERY CURRENT

BATTERY VOLTAGE

LOAD OUTPUT STATE

Possible values:

ON, OFF

Only visible on MPPTs with a load output

LOAD CURRENT Only visible on MPPTs with a load output

History

By pressing SELECT in the status menu, the history menu is entered. Here, the history stored in the MPPT can be viewed. This

contains both overall history and well as a day to day history. For MPPTs with software version up to 1.15, only a few history topics are

available and the day to day history contains 2 days: the current day and the previous day. For MPPTs with software version 1.16 and

onwards, this is a 30 day history.

When viewing values, one can select a different day by pressing the up and down button. The MPPT Control will first show the value for

a short time, then the currently selected day, and then the value again. When viewing an overall history value, pressing the up or down

button will cause the MPPT Control to show “TOTAL”.

Pressing SETUP causes the MPPT Control to go back to the status menu topics when viewing topics or go back to the topics menu

when viewing values.

History topics

SELECT

SETUP

Status

SELECT

SETUP

History values

Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands

General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40

E-mail: sales@victronenergy.com | www.victronenergy.com

The topics are listed in the table below. Only topics marked with a * are visible in case of 2 day history.

Overall topics

TOTAL YIELD* The cumulative yield since the last history reset

MAX PANEL VOLTAGE The maximum panel voltage since the last history reset

MAX BATTERY VOLTAGE The maximum battery voltage since the last history reset

MIN BATTERY VOLTAGE The minimum battery voltage since the last history reset.

(Only available for MPPT software version >= 1.17)

LAST ERRORS

The last 4 errors since the last history reset.

The number of blocks in the lower right of the screens determines

which error is currently shown with 1 block being the latest and 4

blocks being the oldest.

Daily topics

YIELD* The daily yield

MAX POWER* The maximum power per day

MAX PANEL VOLTAGE The maximum panel voltage per day

MAX BATTERY CURRENT The maximum battery current per day

MAX BATTERY VOLTAGE The maximum battery voltage per day

MIN BATTERY VOLTAGE The minimum battery voltage per day

BULK TIME The time spend in bulk per day

ABSORPTION TIME The time spend in absorption per day

FLOAT TIME The time spend in float per day

LAST ERROR The last 4 errors per day

The number of blocks in the lower right of the screens determines

which error is currently shown.

Settings

By pressing SETUP for 2 seconds in the status menu, the settings menu is entered. Here, the settings of the MPPT and MPPT Control

can be viewed and changed. First the topic is shown and when SELECT is pressed, the corresponding value is shown. When SELECT

TO EDIT is OFF, the value is shown before it can be changed by pressing SELECT again. When SELECT TO EDIT is ON, the current

value is shown and a new value can immediately be selected. When LOCK SETUP is ON, settings only be changed after setting LOCK

SETUP to off.

Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands

General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40

E-mail: sales@victronenergy.com | www.victronenergy.com

When editing a value, one can change its value by pressing the up and down buttons. When changing numeric values, pressing

SELECT will go to the next digit, until the last digit. In this case, pressing SELECT will save the setting. When editing non numeric

values, pressing SELECT will save the setting.

Pressing SETUP causes the MPPT Control to go back to the status menu topics when viewing topics or go back to the topics menu

when viewing values.

The settings are listed in the table below. See the manual of the MPPT for the exact meaning of the settings.

01 LOCK SETUP

When this is ON, other settings cannot be changed. When trying to change a setting

(except LOCK SETUP), the MPPT Control will show “LOCK” and show the value of that

setting.

02 BATTERY VOLTAGE

The battery voltage that the MPPT is working with. When the setting is AUTO, it will

show the A character in front of the voltage.

03 BATTERY TYPE

The battery type that the MPPT is working with. This can be set to FIXED or USER.

When set to fixed, the rotary switch on the MPPT determines the actual battery type.

When set to USER, all other charging related settings can be edited.

It will be automatically set to USER when editing a charger related setting.

04 MAXIMUM CURRENT

The maximum charging current

05 BULK TIME LIMIT

The maximum time continuously spent in bulk

06 ABSORPTION TIME LIMIT

The maximum time continuously spent in absorption

07 ABSORPTION VOLTAGE

Battery voltage at which the MPPT switches to the absorption phase

08 FLOAT VOLTAGE

Battery voltage at which the MPPT switches to the float phase

09 TEMP COMPENSATION

10 LOAD OUTPUT

Load output operating mode.

Possible values:

OFF, AUTO, ALT1, ALT2, ON, USER1, USER2

11 LOAD SWITCH HIGH

The high voltage level in case LOAD OUTPUT is set to USER1 or USER2

12 LOAD SWITCH LOW

The low voltage level in case LOAD OUTPUT is set to USER1 or USER2

13 CLEAR HISTORY

Clears the history of the MPPT

14 FACTORY DEFAULTS

Resets the MPPT back to factory defaults

15 BACKLIGHT INTENSITY

Sets the backlight intensity of the MPPT Control

16 BACKLIGHT ALWAYS ON

Determines whether the backlight of the MPPT Control is always on

17 SCROLL SPEED

Determines the scroll speed of the MPPT Control

18 SELECT TO EDIT

When set to OFF, the MPPT Control first shows the value of a setting and SELECT has

to be pressed to be able to edit the value

19 AUTO LOCK

When set to ON, LOCK SETUP will be automatically set to ON, 2 minutes after changing

a setting.

20 SOFTWARE VERSION

The software version of the MPPT Control

21 SERIAL NR

The serial number of the MPPT Control

21 MPPT SOFTWARE VERSION

The software version of the MPPT

21 MPPT SERIAL NR

The serial number of the MPPT

SELECT

Show value

Settings description

Change value

SETUP (2s)

SELECT

Status SELECT

(LOCK SETUP = OFF)

SELECT

(LOCK SETUP = ON or SELECT TO EDIT = OFF)

SETUP

(LOCK SETUP = OFF and SELECT TO EDIT = ON)

SELECT

Otros manuales para MPPT Control

Otros manuales de Controladores de Victron energy

Victron energy

Victron energy BlueSolar MPPT 100/15 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 100/50 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 100/30 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 75/10 Manual de usuario

Victron energy

Victron energy CCGX Manual de usuario

Victron energy

Victron energy CCGX Manual de usuario

Victron energy

Victron energy Bluesolar-5 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/70 Manual de usuario

Victron energy

Victron energy NV-48030 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 75/15 Manual de usuario

Victron energy

Victron energy BlueSolar Manual de usuario

Victron energy

Victron energy Isolated SmartSolar MPPT RS 450/100 Manual de usuario

Victron energy

Victron energy CCGX Manual de usuario

Victron energy

Victron energy SmartSolar MPPT RS 450 100 Manual de usuario

Victron energy

Victron energy BlueSolar 100/50A Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 75/10 Manual de usuario

Victron energy

Victron energy CCGX Instrucciones de funcionamiento

Victron energy

Victron energy VE.Bus BMS Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/35 Manual de usuario

Victron energy

Victron energy Lynx Smart BMS Manual de usuario

Victron energy

Victron energy SmartSolar MPPT 150/35 Manual de usuario

Victron energy

Victron energy BlueSolar MPPT 150/85-Tr Manual de usuario

Victron energy

Victron energy SmartShunt IP65 Manual de usuario

Victron energy

Victron energy SHS 200 MPPT Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario