Vicon VC-600W Manual de usuario

VC-600W, VC-600WS

VC-610W, VC-610WS SERIES

COLOR DOME CAMERAS

About this manual

INSTRUCTION MANUAL XX173-02

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

This installation should be made by a qualified service person and

should conform to the National Electric Code, ANSI/NFPA 70 and

all local codes.

CAMERA DIMENSIONS in. (mm)

Before sending the camera out for repair, check the items below.

If the problem persists after checking these items, contact

your service center.

■If no image appears

Is the coaxial cable attached securely?

Are the power and voltage normal?

Has the iris of the lens inside the camera been

adjusted correctly (with the level volume) ?

Is there adequate illumination?

■If the image is unclear

Is the lens in focus?

Is the lens dirty?

Dirt or fingerprints on the lens can adversely affect the

images. Gently wipe any dirt or fingerprints off the lens

with a soft cloth or lens cleaning paper and cleaning

fluid (commercially available).

Is the monitor adjusted correctly?

PRECAUTIONS

■Do not open or modify

Do not open the case except during maintenance and

installation, as it may be dangerous and cause damage.

■Do not put objects inside the unit

Make sure that no metal objects or flammable substances get

inside the camera. It could cause fire, short-circuits or damages.

■Be careful when handling the unit

To prevent damage, do not drop the camera or subject it to strong shock or vibration.

■Install away from electric or magnetic fields

■Protect from humidity and dust

■Protect from high temperature

Be careful when installing close to the ceiling, in a kitchen or boiler room, as the

temperature may rise to high levels.

■Cleaning

Dirt can be removed from the case only by wiping it with a soft cloth moistened

with a soft detergent solution.

■Mounting Surface

The mounting surface material must be strong enough to support the camera.

TROUBLESHOOTING

SPECIFICATION VC-600W/VC-600WS

SPECIFICATION VC-610W/VC-610WS

GENERAL Spec NTSC PAL

HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

BLC

ME/AE

ATW/AWB

AGC

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via

550TV Lines

0.03fc, 0.3Lux(Scene) With F1.2 Lens

0.45

> 48dB [AGC off]

Internal (12VDC) / External (Line Lock, 24VAC)

1.0Vp-p/75ohm Composite

DIP Switch Select ON/OFF

DIP Switch Select ME/AE (ON/OFF)

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ON/OFF

12VDC(11-20V), 24VAC(20-27V)

12VDC -2.3W, 24VAC - 2.6W

14°F ~ 131°F ( -10°C ~ +55°C )

Up to max.90%

3.3-12mm

BNC(VIDEO), 2P WIRE(Power)

GENERAL Spec NTSC PAL

CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

ME/AE

ATW/AWB

WDR ON/OFF

AGC MAX ON

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via BNC(VIDEO), 2P WIRE(Power)

0.45

0.06fC, 0.6Lux(Scene) With F1.2 Lens

480TV Lines

1.0Vp-p/75ohm Composite

Internal (12VDC) / External (Line Lock, 24VAC)

> 45dB [AGC off]

12VDC -3.9W, 24VAC - 4.0W

12VDC(11-20V), 24VAC(20-27V)

3.3-12mm

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ME/AE (ON/OFF)

Up to max.90%

14°F ~ 131°F ( -10°C ~ +55°C )

DIP Switch Select ON/OFF

DIP Switch Select WDR (ON/OFF)

SPECIFICATION VC-600WDN/VC-600WDN-S

SPECIFICATION VC-600WIR/VC-600WIR-S

GENERAL Spec NTSC PAL

HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

BLC

ME/AE

ATW/AWB

AGC

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via

14°F ~ 131°F ( -10°C ~ +55°C )

Up to max.90%

3.3-12mm

BNC(VIDEO), 2P WIRE(Power)

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ON/OFF

12VDC(11-20V), 24VAC(20-27V)

12VDC -2.3W, 24VAC - 2.6W

Internal (12VDC) / External (Line Lock, 24VAC)

10Vp-p/75ohm Composite

DIP Switch Select ON/OFF

DIP Switch Select ME/AE (ON/OFF)

550TV Lines

0.04fc, 0.4Lux(Scene) With F1.2 Lens

0.45

> 48dB [AGC off]

GENERAL Spec NTSC PAL

HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

BLC

ME/AE

ATW/AWB

AGC

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via

550TV Lines

(BW, No LED) 0.04fc, 0.4Lux(Scene) With F1.2 Lens

0.45

> 48dB [AGC off]

Internal (12VDC) / External (Line Lock, 24VAC)

10Vp-p/75ohm Composite

DIP Switch Select ON/OFF

DIP Switch Select ME/AE (ON/OFF)

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ON/OFF

12VDC(11-20V), 24VAC(20-27V)

MAX LED ON (12VDC - 4.6W, 24VAC - 4.7W)

14°F ~ 131°F ( -10°C ~ +55°C )

Up to max.90%

3.3-12mm

BNC(VIDEO), 2P WIRE(Power)

■LENS ADJUSTMEN

VC-600W/VC-600WS, VC-610W/VC-610WS, VC-600WDN/VC-600WDN-S

VC-600WIR/VC-600WIR-S

■CONNECTION

LENS ADJUSTMENT AND CONNECTION

1. Adjust the panning (360˚) and tilt (51˚) position.

2. Set the zoom position by using Zoom Lever Screw.

3. Set the focus by using Focus Lever Screw.

4. Loosen set screws to adjust roll

(turns camera position top/bottom).

CAUTION

Check for polarity when using a 12VDC power supply.

Input Voltage : 12VDC/24VAC

CLASS 2 NOT WET, CLASS 3 WET

1. Adjust the panning (360˚) and tilt (60˚) position.

2. Set the zoom position by using Zoom Lever Screw.

3. Set the focus by using Focus Lever Screw.

4. Loosen set screws to adjust roll

(turns camera position top/bottom).

PAN - 360˚

TILT - 60˚

Zoom

Focus

Set Screw

(2x)

TILT - 51˚

PAN - 360˚

12VDC Red (+)

Black (-)

24VAC

■VC-600W, VC-600WS

①DIP Switch Functions

(1) Compensating for backlight

ON When backlight is too bright

OFF Normal setting

CAUTION : It will be correctly set by adjusting level volume 5.

(2) Confirming the iris setting

ME(ON) When DC autoiris lens installed

AE(OFF) When fixed iris lens is installed

(3) White balance setting

ATW(ON) Use this under light source below 2500K and

over 9500K of Natrium (Sodium) low

color temperature light

AWB(OFF) Use this under light source between 2500K

and 9500K of fluorescent lamp or

incandescent light

(4) Setting gain control (AGC)

For adjusting the sensitivity of the camera.

Use this setting for shooting in dark environments.

ON Normal setting

OFF Set this when there is excessive noise

②Second Video OUT Connector (Option)

If installer is setting with portable monitor, this connector is used.

Be sure to terminate the last video device at 75 ohms.

③IR LED Connector (Option)

If extra IR LED board is attached, this connector is used.

CAMERA SETTINGS

② PORTABLE

MONITOR

③ IR LED ④ LINE LOCK

ADJUSTMENT

DC LENS

CONTROL

⑥ DC

VARIFOCAL

⑦ POWER

CONNECTOR

①

⑤

④Setting Monitor Synchronization (24 VAC adaptor users)

The camera offers V-phase adjustment over 360°. Vertical

sync disturbance may occur when a switcher is used to switch

between multiple cameras connected to one monitor.

To prevent vertical sync disturbance, adjust ④*.

CAUTION: When using the 12 VDC adaptor, sync setting is

set to internal sync.

⑤Adjusting Level Volume

If the entire image is too dark or bright, or the bakclight

compensation is not correct even after ①is set to "ON",

you need to adjust the level volume.

CCW (LOW) Closes the lens iris, making the entire image darker

CW (HIGH) Opens the lens iris, making the entire image brighter

⑥DC Varifocal Connector

This should be used with ⑤DC IRIS LENS.

⑦Power connector

Connect with AC/DC power, board attached inside.

*Before making any adjustment, confirm that the cameras are connected

to the power supply with the same polarity.

To make an adjustment: While observing the video outputs from

the cameras on an oscilloscope, press the first camera's V-phase

pushbutton. Until vertical sync from all cameras are in phase.

If the first camera's adjustment phase is insufficient, adjust the second

camera's V-phase contol in the oppposite direction until they are in phase.

■VC-610W, VC-610WS : WDR SETTING

⑤ DC LENS

CONTROL

④ LINE LOCK

ADJUSTMENT

② PORTABLE

MONITOR

⑥ DC

VARIFOCAL

③ IR LED

OFF ON

1 AE/ME AE ME

2ATW/AWBAWBATW

3 WDR OFF ON

4 AGC MAX OFF ON

NO FUNCTION DIP S/W

⑦ POWER

CONNECTOR

①DIP Switch Functions

(1) Confirming the iris setting

ME(ON) When DC autoiris lens installed

AE(OFF) When fixed iris lens is installed

(2) White balance setting

ATW(ON) Use this under light source below 2500K and

over 9500K of Natrium (Sodium) low

color temperature light

AWB(OFF) Use this under light source between 2500K

and 9500K of fluorescent lamp or

incandescent light

(3) WDR mode

ON Wide dynamic function is working

OFF Wide dynamic function is not working

(4) Setting gain control (AGC)

For adjusting the sensitivity of the camera.

Use this setting for shooting in dark environments.

ON Normal setting

OFF Set this when there is excessive noise

②Second Video OUT Connector (Option)

If installer is setting with portable monitor, this connector is used.

Be sure to terminate the last video device at 75 ohms.

③IR LED Connector (Option)

If extra IR LED board is attached, this connector is used.

④Setting Monitor Synchronization (24 VAC adaptor users)

The camera offers V-phase adjustment over 360°. Vertical

sync disturbance may occur when a switcher is used to switch

between multiple cameras connected to one monitor.

To prevent vertical sync disturbance, adjust ④*.

CAUTION: When using the 12 VDC adaptor, sync setting is

set to internal sync.

⑤Adjusting Level Volume

If the entire image is too dark or bright, or the bakclight

compensation is not correct even after ①is set to "ON",

you need to adjust the level volume.

CCW (LOW) Closes the lens iris, making the entire image darker

CW (HIGH) Opens the lens iris, making the entire image brighter

⑥DC Varifocal Connector

This should be used with ⑤DC IRIS LENS.

⑦Power connector

Connect with AC/DC power, board attached inside.

*Before making any adjustment, confirm that the cameras are connected

to the power supply with the same polarity.

To make an adjustment: While observing the video outputs from

the cameras on an oscilloscope, press the first camera's V-phase

pushbutton. Until vertical sync from all cameras are in phase.

If the first camera's adjustment phase is insufficient, adjust the second

camera's V-phase contol in the oppposite direction until they are in phase.

■VC-600WDN, VC-600WDNS, VC-600WIR, VC-600WIRS : TDN/IR SETTING

①DIP Switch Functions

(1) Compensating for backlight

ON When backlight is too bright

OFF Normal setting

CAUTION : It will be correctly set by adjusting level volume 5.

(2) Confirming the iris setting

ME(ON) When DC autoiris lens installed

AE(OFF) When fixed iris lens is installed

(3) White balance setting

ATW(ON) Use this under light source below 2500K and

over 9500K of Natrium (Sodium) low

color temperature light

AWB(OFF) Use this under light source between 2500K

and 9500K of fluorescent lamp or

incandescent light

(4) Setting gain control (AGC)

For adjusting the sensitivity of the camera.

Use this setting for shooting in dark environments.

ON Normal setting

OFF Set this when there is excessive noise

⑦

①

PORTABLE

MONITOR ②

③

④

⑤

⑥DC VARIFOCAL

LINE LOCK

ADJUSTMENT

②Second Video OUT Connector (Option)

If installer is setting with portable monitor, this connector is used.

Be sure to terminate the last video device at 75 ohms.

③IR LED Connector (Option)

If extra IR LED board is attached, this connector is used.

④Setting Monitor Synchronization (24 VAC adaptor users)

The camera offers V-phase adjustment over 360°. Vertical

sync disturbance may occur when a switcher is used to switch

between multiple cameras connected to one monitor.

To prevent vertical sync disturbance, adjust ④*.

CAUTION: When using the 12 VDC adaptor, sync setting is

set to internal sync.

⑤Adjusting Level Volume

If the entire image is too dark or bright, or the bakclight

compensation is not correct even after ①is set to "ON",

you need to adjust the level volume.

CCW (LOW) Closes the lens iris, making the entire image darker

CW (HIGH) Opens the lens iris, making the entire image brighter

⑥DC Varifocal Connector

This should be used with ⑤DC IRIS LENS.

⑦Power connector

Connect with AC/DC power, board attached inside.

*Before making any adjustment, confirm that the cameras are connected

to the power supply with the same polarity.

To make an adjustment: While observing the video outputs from

the cameras on an oscilloscope, press the first camera's V-phase

pushbutton. Until vertical sync from all cameras are in phase.

If the first camera's adjustment phase is insufficient, adjust the second

camera's V-phase contol in the oppposite direction until they are in phase.

Otros manuales para VC-600W

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon Roughneck AI V2000D Series Manual de usuario

Vicon

Vicon V9360-1 Guía de inicio rápido

Vicon

Vicon SN688D-WIR Manual de usuario

Vicon

Vicon V682-PTZ Manual de usuario

Vicon

Vicon Surveyor MKII Series XX282-00-01 Manual de usuario

Vicon

Vicon V920B Series Manual de usuario

Vicon

Vicon Surveyor 99 Manual de usuario

Vicon

Vicon V992D-N4 Manual de instrucciones

Vicon

Vicon 360 Multi-Sensor Camera Series Manual de usuario

Vicon

Vicon VC-630 Manual de usuario

Vicon

Vicon Surveyor 282-20-02 Series Manual de usuario

Vicon

Vicon V942D-W312MIR Manual de usuario

Vicon

Vicon V894MSH Manual de usuario

Vicon

Vicon Roughneck Pro V2000D Series Manual de usuario

Vicon

Vicon VN-755IP Manual de usuario

Vicon

Vicon Surveyor MKII Series XX282-00-01 Manual de usuario

Vicon

Vicon I-ONYX VND-970IP Manual de usuario

Vicon

Vicon V905-CUBE Manual de usuario

Vicon

Vicon XX258-50-01 Roughneck Series Manual de usuario

Vicon

Vicon V920B Series Manual de usuario

Vicon

Vicon Surveyor 4 Manual de usuario

Vicon

Vicon V980B Series Manual de usuario

Vicon

Vicon V1020-WIR-180 Manual de usuario

Vicon

Vicon Cruiser SN663V-B-EX Instrucciones de funcionamiento

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario