Vicon V988B Manual de usuario
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform
precisely as described in the documentation. This system has not been designed to be
used in life-critical situations and must not be used for this purpose.
Docum
ent Number: 8009-8302-20-00 Product specifications subject to change without
notice. Issued: 6/18 Copyright © 2018 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: 631-952-2288)
Fax: 631-951-2288
Toll Free: 800-645-9116
24-Hour Technical Support:
800-34-VICON
XX302-20-00
V988B
Network 4K Bullet Camera
Quick Guide
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EX- POSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT
ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of dangerous voltage within the
product’s
enclosure that may be of sufficient magnitude to constitute a risk of
electric shock
to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
2
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet
appareil
nume
`
rique
de
la
classe
A
est
conforme
a
´
la
norme
NMB-003
du
Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
3
IMPORTANT SAFETY INSTRUCTIONS
1. Readtheseinstructions.
2. Keeptheseinstructions.
3. Heedallwarnings.
4. Followallinstructions.
5. Donotusethisapparatusnearwater.
6. Cleanonlywithdrycloth.
7. Donotblockanyventilationopenings.Installinaccordancewiththemanufacturer’sinstructions.
8. Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,orotherapparatus
(includingamplifiers)thatproduceheat.
9. Donotdefeatthesafetypurposeofthepolarizedorgrounding‐typeplug.Apolarizedplughastwo
bladeswithonewiderthantheother.Agroundingtypeplughastwobladesandathirdgrounding
prong.Thewidebladeorthethirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnotfit
intoyouroutlet,consultanelectricianforreplacementoftheobsoleteoutlet.
10. Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplugs,convenience
receptacles,andthepointwheretheyexitfromtheapparatus.
11. Onlyuseattachments/accessoriesspecifiedbythemanufacturer.
12. Useonlywiththecart,stand,tripod,bracket,ortablespecifiedbythe
manufacturer,orsoldwiththeapparatus.Whenacartisused,usecaution
whenmovingthecart/apparatuscombinationtoavoidinjuryfromtip‐over.
13. Unplugthisapparatusduringlightningstormsorwhenunusedforlong
periodsoftime.
14. Referallservicingtoqualifiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeen
damagedinanyway,suchaspower‐supplycordorplugisdamaged,liquidhasbeenspilledorobjects
havefallenintotheapparatus,theapparatushasbeenexposedtorainormoisture,doesnotoperate
normally,orhasbeendropped.
15. CAUTION–THESESERVICINGINSTRUCTIONSAREFORUSEBYQUALIFIEDSERVICEPERSONNEL
ONLY.TOREDUCETHERISKOFELECTRICSHOCKDONOTPERFORMANYSERVICINGOTHERTHAN
THATCONTAINEDINTHEOPERATINGINSTRUCTIONSUNLESSYOUAREQUALIFIEDTODOSO.
16. Usesatisfyclause2.5ofIEC60950‐1/UL60950‐1orCertified/ListedClass2powersourceonly.
17. ITEistobeconnectedonlytoPoEnetworkswithoutroutingtotheoutsideplant.
4
1
Introduction
Vicon’s V988B-W311MIR HD IP Bullet Camera is designed for performance in demanding security installations.
The camera provides 4K (8 MP) resolution with a 3.6-11 mm motorized varifocal lens. The camera offers IR
illuminators that provide superior images in low-light environments.
The V988B-W311MIR supports H.264/H.265 compression technology, drastically reducing file sizes and
conserving valuable network bandwidth. M-JPEG compression is also provided. The camera can provides quad
streaming for multi-camera displays.
1.1
Components
This system comes with the following components;
Network
Camera 1
Installation Guide 1
Accessory Kit 1
Note 1. Check your package to make sure that you received the complete system, including all components
listed above.
Note 2. Adapter for 12 VDC is not supplied.
5
2
Installation
Forthenetworkcameratooperate,it is necessary to connect anetworkcablefor
datatransmissionand
powerconnectionfromapoweradapter. Dependingonoperation
methods, it is possible to connect an
alarmcable.
2.1
Overview
•
Dimension
Dimensions Unit: mm
•
Extension Cable
No. Item Description
1
RJ-45
Ethernet, RJ-45 port compatible
with 10/100Mbps PoE Modular Jack
2
DC Jack Main Power, DC Jack, 12 VDC
3
AI: Alarm In
Alarm input and output, 3-pin terminal
G: GND
AO: Alarm Out
4
MIC: Audio In
Audio line input, 2-pin terminal
G: GND
5
SPK: Audio Out
Audio line output, 2-pin terminal
G: GND
6
•
Installing Camera
To mount the bullet camera, fix the base of the camera with the three screws provided in the
accessory kit.
7
2.2
Connection
•
Micro SD memory slot on the bottom board
Remove the cap at bottom of the camera to insert the SD memory card.
•
Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is used
for dir e ct con nection to PC, while a dire c t cable is us ed for
connection to a hub. You can also use a router featuring
PoE (Power over Ethernet) to
supply power to the camera.
•
Connecting Alarms
AI (Alarm In): You can use external devices to signal the network camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm In) and G
(Ground) connectors.
G (Ground): Connect the ground side of the alarm input and/or alarm output to the G
(Ground) connector.
AO (Alarm Out): The network camera can activate external devices such as buzzers
or lights. Connect the
device to the AO (Alarm Out) and G (Ground) connectors.
•
Connecting the Power
Connect the power of 12VDC for the network camera. Connect the positive (+) pole to the ‘+’ position and the
negative (-) pole to the ‘-’ position for the DC power.
–
Be careful not to reverse the polarity when connecting the power cable.
–
A router featuring PoE (Power over Ethernet) can also be used to supply power to
the camera.
–
For the power specifications, refer to the appendix, product specification intheUsermanual.
–
If PoE and 12 VDC are both applied, the camera will be supplied with power from
PoE.
•
Connecting Audio
Connect speaker to audio line output and external Mic to audio input line.
8
2.3
Resetting to the Factory Default Settings
To reset the network camera to the original factory settings, go to the Setup
>
System
>
Maintenance web
page (described in “System
>
Maintenance” of User Manual) or use the
Reset button on the network camera
inside the bottom cap.
•
Using the Reset button:
Follow the instructions below to reset the network camera to the factory default settings using the Reset
button.
1)
Switch off the network camera by disconnecting the power adapter.
2)
Open the top cap.
3)
Press and hold the Reset button with a straightened paperclip while reconnecting the
power.
4)
Keep the Reset button pressed at least 5 (or more) seconds.
5)
Release the Reset button.
6)
The network camera resets to factory defaults and restarts after completing the factory
reset.
7)
Close the bottom cap tightly to ensure waterproof.
CAUTION: When performing a Factory Reset, you will lose any settings that have been
saved. (Default
IP 192.168.30.220)
9
2.4
Network Connection & IP Assignment
ThenetworkcameraisdesignedforuseonanEthernetnetworkandrequiresanIPaddressforaccess.Most
networkstodayhaveaDHCPserverthatautomaticallyassignsIPaddressestoconnecteddevices.Bythe
factorydefault,yourcameraissettoobtaintheIPaddressautomaticallyviaDHCPserver.Ifyournetwork
doesnothaveaDHCPserverthenetworkcamerawilluse192.168.1.100asthedefaultIPaddress.
IfDHCPisenabledandtheproductcannotbeaccessed,runthe“SmartManager”utilitytosearchand
allocateanIPaddresstoyourproducts,orresettheproducttothefactorydefaultsettingsandthenperform
theinstallationagain.TheutilitycanbefoundontheViconwebsitewww.vicon‐security.com,onthe
SoftwareDownloadspageforViconcameras.
1)
Connect the network camera/device to the network and power up.
2)
Start SmartManager utility (Start
>
All programs
>
SmartManager
>
SmartManager); the main window
displays. After a short while any network devices connected to the network will be displayed in the list.
3)
Select the camera on the list and click right button of the mouse. The pop-up menu below displays.
4)
Select Assign IP. The Assign IP window displays. Enter the required IP address.
NOTE: For more information, refer to the SmartManager User Manual.
10
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vicon
Vicon
Vicon V9360-1 Manual de usuario
Vicon
Vicon SurveyorVF SVFT-M Manual de usuario
Vicon
Vicon V840D Series Manual de usuario
Vicon
Vicon Roughneck Pro V2002D-PTZ Manual de usuario
Vicon
Vicon V661-N-1 Series Instrucciones de funcionamiento
Vicon
Vicon VC2200-12 Guía del usuario
Vicon
Vicon Surveyor MKII Series XX282-20-00 Manual de usuario
Vicon
Vicon V960D Series Manual de usuario
Vicon
Vicon S2000-MSH-HHB Surveyor 2000 Manual de usuario
Vicon
Vicon Cruiser SN660V Instrucciones de funcionamiento
Vicon
Vicon Surveyor MKII Manual del propietario
Vicon
Vicon ROUGHNECK V910 Manual de usuario
Vicon
Vicon Roughneck Pro V2000B Series Manual de usuario
Vicon
Vicon V922B-W551-A1 Manual de usuario
Vicon
Vicon SN688D-WIR Manual de usuario
Vicon
Vicon Roughneck V920D Series Instrucciones de instalación y funcionamiento
Vicon
Vicon V662V-Series Instrucciones de funcionamiento
Vicon
Vicon SURVEYORVFT SVFT Manual de usuario
Vicon
Vicon Surveyor 282-20-02 Series Manual de usuario
Vicon
Vicon V1008-WIR-180-1 Manual de usuario
