Vicon V672D Instrucciones de funcionamiento
V672D HD Analog Dome Cameras
Installation and Operation Guide
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform
precisely as described in the documentation. This system has not been designed to be
used in life-critical situations and must not be used for this purpose.
Document Number: 8009-8299-10-00 Product specifications subject to change without
notice. Issued: 2/17 Copyright © 2017 Vicon Industries Inc. All rights reserved.
XX299-10
Vicon Industries Inc.
Tel: 631-952-2288) Fax: 631-951-2288
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266) UK: 44/(0) 1489-566300
www.vicon-security.com
2
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept anyinterference received, including interference thatmaycause undesired
operation.
FCC INFORMATION : This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
WARNING : This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
3
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.\
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the cart, stand, tripod, bracket, or table specified by
The manufacturer, or sold with the apparatus. When a cart is used,
Use caution when moving the cart/ apparatus combination to avoid
Injury from tip-over.
9. CAUTION – THESE SERVICING IN STRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2
power source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
The lighting flash with arrowhead symbol, within an equilateral triangle, is
Intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product`s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
LIMITATION OF LIABILITY
THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL
RESPECTS; HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY
CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR
NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH
CHANGES.
4
PRECAUTIONS
Before installation, carefully read the manual to ensure correct operation and setup,
heeding all warnings and instructions.
Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Ensure manual is kept in good condition for future use.
Do not install the device near any heat sources such as radiators, heat registers, stoves,
or other equipment(including amplifiers) that produce heat.
Only use attachments/accessories specified by the manufacturer.
Should any liquid get into the housing, immediately disconnect the device from the power
supply and have it checked by authorized personnel before reusing.
Do not install the device in a place where it is exposed to gas or oil.
Installation and servicing by authorized personnel only, adhering to local safety
regulations.
Unless you are an authorized technician, never try to dismantle the device. To avoid
electric shock, never remove the screws or covers.
If a camera, do not expose the device to radioactivity. It will cause serious damage to the
CCD.
Use Certified/Listed Class 2 power source only.
Cleaning
Clean the device with a slightly damp soft cloth. Use a mild household detergent. Never
use strong solvents such as thinner or benzene as they might damage the finish of the
unit.
5
TABLE OF
CONTENTS
INTRODUCTION ------------------------------------------------------------------------- 6
CAMERA CONNECTION -------------------------------------------------------------- 7
LENS ADJUSTMENT ------------------------------------------------------------------- 7
CONTENTS OF PACKAGE ----------------------------------------------------------- 8
INSTALLATION --------------------------------------------------------------------------- 9
STRUCTURE OF THE SETUP MENU --------------------------------------------- 13
DC AUTO IRIS LENS ------------------------------------------------------------------- 19
SPECIFICATIONS ----------------------------------------------------------------------- 20
EXTERNAL DIMENSION ------------------------------------------------------------ 21
６
INSTRUCTION
The 1/2.8” 2.1M Full HD CMOS camera, especially for closed circuit television
CCTV and security surveillance application.
Features:
• High performance SONY 1/2.8” 2.1M STARVIS CMOSTM
• Min. illumination 0.03 lux(Color), 0 lux(BW, IR LED ON)
• Auto electronic shutter [1/30 (1/25) ~ 1/30,000] and manual electronic shutter
modes
• True WDR (Wide Dynamic Range) in HD mode
• D-WDR (Digital Wide Dynamic Range) in composite mode
• BLC (Back-light compensation)
• HLC (High-light compensation)
• Auto and manual white balance modes (AUTO/AUTOext/Manual/AWB)
• Day & Night (ICR): Auto/Color/BW/EXTERN
• OSD (on screen display)
• DNR (Digital Noise Reduction)
• IR Range distance up to 98 ft/30 m
• 30EA, 850nm IR LEDs
• Privacy Mask function (16 zones)
• Motion Detection (4 zones)
• Defog
• Composite Video Output (700TV Lines)
• Operates in 24 VAC ± 10%/12 VDC ± 10%
• Use Certified / Listed Class 2 Power source only
IMPORTANT: The user of this camera is responsible for checking and
complying with local, state, and federal laws and statutes concerning the
recording and monitoring of audio signals.
７
CAMERA CONNECTION
①Lens: Allows a wide area to be monitored.
②Power: 24 VAC/12 VDC power source from a 12 VDC or 24 VAC ±10%,
60/50Hz±1Hz; use Certified/Listed Class 2 power source only.
12 VDC Type => 12 VDC ±10% (12 VDC is polarity dependent)
If using 12 VDC power adaptor, use power supply capable of supplying 8 Watts.
③Video (HD): BNC (Black) connector used to connect the camera to a DVR, etc.
④Video (CVBS): BNC (Yellow) connector used to connect the camera to a
DVR, etc.
⑤SPOT: Spot connector used to check video(CVBS) output.
８
LENS ADJUSTMENT
Tact Switch for motorized lens control
without being in the OSD:
Up – Zoom in
Down – Zoom out
The lens will then autofocus the lens
based on the overall scene being viewed.
CONTENTS OF PACKAGE
Installation of the camera must be performed by qualified service personnel in
accordance with all local and national electrical and mechanical codes.
Carefully remove the color camera and its accessories from the carton and verify that
they were not damaged in shipment.
The content of the package includes:
1. Camera in housing
2. This manual
3. Accessory kit for installing
4. Drilling guide label
９
INSTALLATION - Surface Mount
1. Loosen the three Torx screws as shown in Figure 1.
Do not remove the screws. Lift the trim ring off the mount and set aside.
2. Drill the mounting location using the supplied drilling guide.
3. Attach the surface mount to the ceiling as shown in Figure 2.
M5x30 fasteners are supplied; only use if they are suitable for the mounting surface.
4. Insert the bottom case into the surface mount as shown in Figure 2.
Turn the locking flaps outward as shown in Figure 3 and 4 to attach the bottom case to
the surface mount.
5. Install the trim ring onto the surface mount and tighten the Torx screws.
１０
INSTALLATION - Surface Mount
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vicon
Vicon
Vicon V1020-WIR-180 Manual de usuario
Vicon
Vicon SurveyorVFT SVFT-M Manual de usuario
Vicon
Vicon V-CELL-HD Manual de usuario
Vicon
Vicon SVFT-PRS22E Manual de usuario
Vicon
Vicon VC-600W Manual de usuario
Vicon
Vicon V840D Series Manual de usuario
Vicon
Vicon Cruiser SN693V Manual de usuario
Vicon
Vicon V9360-1 Manual de usuario
Vicon
Vicon XX247-32-00 Manual de usuario
Vicon
Vicon Surveyor 282-20-02 Series Manual de usuario
Vicon
Vicon V920B Series Manual de usuario
Vicon
Vicon CE202D-WN Manual de usuario
Vicon
Vicon Series 234-00-02 Instrucciones de funcionamiento
Vicon
Vicon VC5050-DSP Manual de usuario
Vicon
Vicon 360 Multi-Sensor Camera Series Manual de usuario
Vicon
Vicon V3FD Series Manual de usuario
Vicon
Vicon ROUGHNECK V-CELL-HD-B Manual de usuario
Vicon
Vicon VC-700W Manual de usuario
Vicon
Vicon VC2650-DSP Manual de usuario
Vicon
Vicon VC-3000-DSP Manual de usuario
