Valor ZERO CLEARANCE KIT Manual de usuario

Part 590839

ZERO CLEARANCE KIT

for Models 737UN, 737UP & 737BN

INSTALLATION INSTRUCTIONS

1. GENERAL

This kit must be used when installing heater Model 737UN, 737UP or737BN into anenclosure constructed of

combustible material. The heater must also be connected to an approved flue pipe.

This kit has been designed to act as a fireplace opening forinstallation during the constructionof the appliance enclosure.

The heateris designed to be fittedinto the opening after the walls and hearth have been finished.

2. FRAMING.

Minimum clearances to combustible materials and framing details are shownin fig.1,.

Though not mandatory for this appliance, if the bottom of the appliance is at floor level, we recommend that there is a

hard surfaced hearthareain front of the fireplace for bothaesthetic and maintenance purposes.This may be finished in

brick, ceramic tile, marble, etc.

To enable the heater to be installed correctly the height of the finished floor surface in front of the appliance

must be known before constructing the frame. The bottom of the zero clearance kit must be installed at the

height of the finished floor surface.

SHELF DEPTH “A” 25mm 50mm 75mm 100mm 125mm 150mm 175mm

HEIGHT FROM BASE OF

HEATER “B” 960mm 1010mm 1040mm 1090mm 1140mm 1190mm 1240mm

600A711/02

Fig.1

Fig. 2

3. KIT COMPONENTS

The kit contains the following (fig. 3):

•1 top panel.

•1 rear panel with spacers.

•1 right side panel with spacers

•1 left side panel with spacers.

•1 base panel.

•2 top panel spacers.

•1 inlet opening cover plate.

•1 extension bracket for thermostat coil.

•1 screw pack.

•4. ASSEMBLE THE ZERO CLEARANCE KIT

•Assemble the rear, two sides, top and base panels, to form the zero

clearance box, using the screws provided, (see fig. 3)

•Fit the top spacers to the top panel using the screws provided(fig. 3).

•Fit the inlet opening cover plate to the rectangular opening which will not be

used for the gas inlet pipe.

•Secure the kit to the framing. Two fixing holes are provided in the base.

Alternatively the side flanges may be drilled and countersunk woodscrews

used.

•Fit the flue pipe through the hole in the top panel and secure to the appliance

vent connector as described in the appliance instructions.

•All wall and hearth finishes can now be applied.

•5. INSTALLING THE APPLIANCE

•Detach the thermostat coil from securing

bracket at right side of appliance (see fig. 5).

•Fit the thermostat coil extension bracket to the

end of the existing bracket with the two screws

provided (fig. 6).

•Secure the thermostat coil to the tab at the top

right of the extension bracket.

•The unit can now be installed exactly as in a

masonry fireplace, see the appliance installation

guide.

If the appliance does not have a thermostat coil

bracket, work through the following steps

•Detach the thermostat coil from the securing clip at the right side of the

appliance.

•Bend thermostat extension bracket along perforated line through 90º (see

fig. 7).

•Fit the thermostat coil extension bracket to the two holes with the 2 screws

provided. (see fig. 7).

•Secure the thermostat coil to the tab at the top right of the extension

bracket.

•The unit can now be installed exactly as in a masonry fireplace, see the

appliance installation guide.

Fig.3

Fig.7

Fig. 4

Fig. 5

Fig. 6

Tabla de contenidos

Otros manuales de Accesorios para chimeneas de Valor

Valor

Valor G3 Series Manual de usuario

Valor

Valor MADRONA Series Manual de usuario

Valor

Valor LEGEND G3.5 Manual de usuario

Valor

Valor 546LFB ZC Portrait Ledgeview Front Instrucciones de instalación

Valor

Valor GV60CKO Manual de usuario

Valor

Valor L2 SERIES Manual de usuario

Valor

Valor 720SWK-M Manual de usuario

Valor

Valor LX2 Series Manual de usuario

Valor

Valor H6 Series Manual de usuario

Valor

Valor PORTRAIT BSK531 Manual de usuario

Valor

Valor H5 1184ECAS Manual de usuario

Valor

Valor Legend G3.5 Series Manual de usuario

Valor

Valor LT2 2700K Manual de usuario

Valor

Valor HORIZON H4 Series Manual de usuario

Valor

Valor G3.5 Series Manual de usuario

Valor

Valor Legend G3 Manual de usuario

Valor

Valor H6 Series Manual de usuario

Valor

Valor 1430CIK Manual de usuario

Valor

Valor G3.5 Series Manual de usuario

Valor

Valor 1875LFB Manual de usuario

Valor

Valor 555CFK Manual de usuario

Valor

Valor 1240BPK Manual de instrucciones

Valor

Valor L3 Manual de usuario

Valor

Valor BSK613 Manual de usuario

Manuales populares de Accesorios para chimeneas de otras marcas

Exodraft

Exodraft Xzense Manual de usuario

Whalen

Whalen Ruso MNFP62BF23-6 Manual de usuario

Lopi

Lopi Hearthview 864 Manual de usuario

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manual de usuario

EdilKamin

EdilKamin SERBATOIO 250 Guía de inicio rápido

Bronpi

Bronpi KIT-1 Manual de usuario

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manual de usuario

Travis Industries

Travis Industries 33 DVI Manual de usuario

Superior

Superior ASD3628-TI Manual de usuario

pleasant hearth

pleasant hearth OFP28WG Manual de usuario

IHP

IHP Astria Series Manual de usuario

Firegear

Firegear FG-H-2110SS Manual de usuario

Nibe

Nibe Contura C i31 Manual de usuario

kozy heat

kozy heat KZK-052 Manual de usuario

SimpliFire

SimpliFire SF-WM36 Manual de usuario

Bluegrass Living

Bluegrass Living BC18NR Guía de inicio rápido

pleasant hearth

pleasant hearth IRIS SCROLL Manual de usuario

Cooke

Cooke Glass Wind Guard Manual de usuario