IHP Astria Series Manual de usuario

P/N 900418-00

Rev. NC 01/2015

HEARTH PRODUCTS

SUPPLEMENTAL INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FRONT AND END FACE ASSEMBLY

REMOVAL AND REINSTALLATION

DIRECT VENT AND B-VENT GAS FIREPLACES

DANGER

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

• Install only when ﬁreplace is OFF and COLD.

• Fireplace surfaces get EXTREMELY HOT!

• The glass on the front of the ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe burns if touched. Even after

the gas is turned off, ﬁreplace surfaces remain extremely hot.

NOTE: The barrier contained herein is designed to reduce the risk

of burns from the hot viewing glass and shall be installed for the

protection of children and other at-risk individuals.

FRONT AND END FACE ASSEMBLY WITH BARRIER

REMOVAL AND REINSTALLATION INSTRUCTIONS

P900418-00

All barriers are designed to reduce the risk of injury from contact with

hot glass. See warnings in the Installation and Care and Operations

manual (IICO) for ﬁreplaces which require a barrier.

REMOVING THE FRONT FACE OR END ASSEMBLY FOR CLEANING OR

OTHER MAINTENANCE

Do not remove rthe front face or end assembly unless the ﬁreplace is

off and the appliance is cool. All front face and end assemblies with

barriers must be in place when the ﬁreplace is in use.

In ﬁreplaces with front face or end assemblies (see Figure 1), remove

the assembly in the following manner:

Remove the front face or end assembly by lifting top and bottom

evenly approximately 1/2” and pulling straight out from the unit once

the brackets are disengaged.

NOTE: Front face or end assembly with barrier must be reinstalled

prior to operation.

NOTE: If the barrier becomes damaged, the barrier

must be replaced with the manufacturer’s barrier

for the appliance. See barrier identiﬁcation label

on barrier.

Assembly

Barrier in

Assembly

Assembly

Brackets

Figure 1 - Typical Assembly with Barrier

Reinstall the front face or end assembly in the following manner.

1. Hold the assembly with its brackets approximately 1/2” from and

1/2” above the slots in the face of the ﬁreplace

2. Move the assembly into place with assembly brackets directly above

the ﬁreplace slots by pressing the assembly against the unit

3. Push the assembly down over the slots, engaging them and holding

the assembly in place

fire-parts.com

INNOVATIVE HEARTH PRODUCTS • GAS FIREPLACES • BARRIER REMOVAL AND REINSTALLATION INSTRUCTIONS

P/N 900418-00 Rev. NC 01/2015

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com

Innovative Hearth Products reserves the right

to make changes at any time, without notice,

in design, materials, speciﬁcations, prices and

also to discontinue colors,styles, and products.

Consult your local distributor for ﬁreplace

code information Printed in U.S.A. © 2014

Innovative Hearth Products, LLC .

P900418-00

INSTALLING A NEW MANUFACTURER’S BARRIER

A barrier should never be removed except for the replacement of a

damaged barrier. The barrier and assembly must be replaced before

using the appliance. After removing the front face or end assembly,

remove the barrier in the following manner.

1. Facing the back side of the front face or end assembly, lift up on the

barrier and swing the bottom of the barrier out

2. Remove the barrier

Install a new, manufacturer’s replacement barrier in the following man-

ner:

1. With the barrier identiﬁcation label facing you and positioned at the

bottom, push the barrier up, inside the top of the assembly

2. Swing the barrier in at the bottom until it rests on the barrier shelf

(see Figure 3)

NOTE: Front face or end assembly with barrier must be reinstalled

prior to operation.

Reinstall the front face or end assembly in the following manner.

1. Hold the assembly approximately 1/2” from and 1/2” above the slots

in the face of the unit

2. Move the assembly brackets into place directly above the ﬁreplace

slots by pressing the assembly

3. Push the assembly brackets down over the ﬁreplace slots, engaging

them and holding the assembly in place

Figure 3 - Replacing the Barrier in an Assembly

Assembly barrier

shelf - barrier sits

on top

Figure 2 - Typical Front Face Assembly (left) and barrier (right)

Bottom assembly

brackets (top not

shown)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

fire-parts.com

Otros manuales de Accesorios para chimeneas de IHP

Manuales populares de Accesorios para chimeneas de otras marcas

Valor

Valor L2 1700K Manual de usuario

Exodraft

Exodraft Xzense Manual de usuario

Whalen

Whalen Ruso MNFP62BF23-6 Manual de usuario

Lopi

Lopi Hearthview 864 Manual de usuario

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manual de usuario

EdilKamin

EdilKamin SERBATOIO 250 Guía de inicio rápido

Bronpi

Bronpi KIT-1 Manual de usuario

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manual de usuario

Travis Industries

Travis Industries 33 DVI Manual de usuario

Superior

Superior ASD3628-TI Manual de usuario

pleasant hearth

pleasant hearth OFP28WG Manual de usuario

Firegear

Firegear FG-H-2110SS Manual de usuario

Nibe

Nibe Contura C i31 Manual de usuario

kozy heat

kozy heat KZK-052 Manual de usuario

SimpliFire

SimpliFire SF-WM36 Manual de usuario

Bluegrass Living

Bluegrass Living BC18NR Guía de inicio rápido

pleasant hearth

pleasant hearth IRIS SCROLL Manual de usuario

Cooke

Cooke Glass Wind Guard Manual de usuario