Valor GV60WIFI Manual de usuario
1
Installation Manual
For Valor heaters using the GV60 Valve
September 2019
4007703
Introduction
Any Valor replace using a GV60 Valve may
be upgraded to allow the installation of the
GV60WIFI module, allowing the homeowner
to put the replace onto the home’s WiFi
system.
Depending on the existing installation,
some parts of the replace may need to
be added or upgraded. This document
outlines the required components and the
instructions to physically install them.
The WiFi module must be wired into a
compatible receiver, complete with SI port
as shown below.
Electrical Requirements
A grounded, single phase, 115VAC power
supply is required for operation of the WiFi
system.
If the AC main power is lost, WiFi operation
will be lost also. Remote operation of the
replace (using the remote handset) can
still be achieved if battery power is properly
supplied and available.
WARNING
All electrical installations must
be performed by a qualied
electrician and must be
electrically wired and grounded
in accordance with local
codes, or, in the absence of
local codes, with the National
Electrical Code, ANSI/NFPA 70
or the Canadian Electrical Code,
CSA C22.1.
Wiring Diagram
2
Required Components
To use the Valor 10 app and run the replace on a WiFi
system, the following components are required:
• WiFi module (and receiver cable)
• Maxitrol model B6R-W2ZV-0 (check label)
• Receiver
• Maxitrol model B6R-RAP (check label)
• V-Module (and receiver and power cables)
• Maxitrol model G6R-BUMV3 (check label)
Model number
Model number
Model number
• Valor 10 Remote Handset (and holder)
• Battery holder (and receiver cable)
See "Part Numbers" on page 4 for full details.
Available Kits
GV60WIFI: This kit is suitable only for LX1 and LX2
replaces manufactured after July 2019, or other
installations that have all required components except
the WiFi module. This kit includes:
• (1) WiFi module and connector cable
GV60WIFI2: This kit is required for any installation that
does not include all the required components. This kit
includes:
• (1) WiFi module (B6R-W2) and cable
• (1) Receiver (B6R-R9P)
• (1) V-Module (G6R-BUMV3) and cables
• (1) Valor 10 Remote Handset and wall holder
• (1) Battery holder and cable
Note: If you are unsure of whether the
equipment in your installation meets requirements,
please contact your local Valor dealer:
valorreplaces.com/contact/
3
Installation
Installing the V-Module
1. Connect the V-Module’s “Power” terminal to the
power cable, using the included Molex connector.
2. Plug the power cable into an available receptacle,
or hard wire back to available power. Consult local
electrical codes.
3. Connect the V-Module’s “Receiver” terminal to the
“Module” port on the Receiver.
4. Attach Velcro and place the V-Module into the re-
place as space allows.
5. Connect the light cable connector to the V-Module
(if applicable).
6. Connect the fan cable connector to the V-Module (if
applicable).
Replacing the Receiver
7. Identify and disconnect leads from existing
receiver.
8. Remove and recycle the old receiver.
9. Reconnect the following cables to the receiver (new
cables not required)
• V-Module cable
• Ignition cable
• Interruptor cable (to yellow terminal)
• Interruptor cable (to red terminal)
• Wiring harness (receiver to valve)
• Wall switch cable (if applicable)
• Battery holder cable (if applicable)
10. Attach Velcro and place the new receiver in place of
the old one.
Note: If you are only installing the GV60WIFI
kit, proceed directly to Step 12, "Installing the WiFi
Module".
WARNING
When installing any cables or wires in
the steps following, be sure to gather any
extra wire with cable ties and prevent
them touching the rebox or other hot
metal surfaces in the replace!
Installing the Battery Holder
11. Install 4 AA batteries in the battery holder.
12. Connect the battery holder cable to the holder and
to the Receiver.
13. Attach Velcro and place the battery holder into the
replace as space allows.
Synching the Remote Handset
14. Insert two 1.5 V AAA alkaline batteries in the hand-
set.
15. Locate the RESET button on the front side of the
receiver.
16. With a thin object, press and hold the receiver’s
RESET button until you hear one short and one long
beeps. After the second beep, release the reset but-
ton.
17. Within the subsequent 20 seconds, press and hold
the button on the remote handset. will be
displayed on the handset during the pairing se-
quence. You will hear two short beeps conrming
the pairing is done.
Installing the WiFi Module
18. Connect the WiFi module’s “Receiver” port to the
“SI” port on the Receiver using the cable.
19. Attach Velcro and place the WiFi module into the
replace as space allows.
Your upgrade installation is now complete. Supply
power to the replace and proceed to "Valor 10 WiFi
Control Software Instructions", document 4007972.
SI port
Note: Install the WiFi module with the Reset
button facing in the direction of easiest access. If
installing in the LX2/2200 replace, be sure to place
the module under the heat shield.
Installation
4
Designed and Manufactured by / for
Miles Industries Ltd.
190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1
Tel. 604-984-3496 Fax 604-984-0246
www.valorreplaces.com
Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.
Resetting the Module
In the event of a nonrecoverable failure, or if the
homeowner needs to set up a new home network, the
module can be easily reset to factory default to allow all
the setup steps in this guide to be done again.
Note: Performing this action removes all network data
from your WiFi module!
To reset the module:
1. Ensure it is receiving power from the replace.
2. Insert a thin object (eg. paper clip) in the small
opening below the WLAN LED on the unit and press
until you feel the reset button click.
3. Hold the reset button for 20 seconds.
Reset button
During the reset, the Receiver LED will blink blue
slowly, then quickly. After the full 20 seconds, it will
blink blue slowly again, and you can release the
button. The Receiver LED will turn solid green.
Upon reset, the WLAN will briey blink red (to
indicate network loss) and then blink blue (to
indicate seeking a connection).
The module is now at factory default and you
are ready to congure per the instructions in For
Software Information (see below).
For Software Information
For information on how to use
the Valor 10 software app to
congure and operate your
upgraded replace, please see
"Valor 10 WiFi Control Software
Instructions", document 4007972.
Part Numbers
Description Valor Part # Maxitrol Part # Qty in GV60WIFI Qty in GV60WIFI2
Receiver, 2 way 4005597 B6R-RAP -1
10 button "Valor 10" remote handset 4007548 B6R-H9TV4PBD -1
Comfort control wall holder 4004459 G60-ZWHFG -1
V-Module relay box 4002530 G6R-BUMV3 -1
Receiver to relay cable (1000 mm) 4002531 G6R-CB10 -1
WiFi module 4007685 B6R-W2ZV-0 1 1
WiFi cable (1000 mm) 4007686 G60-ZCSW1000 1 1
Battery box cable 4006552 -1
Battery box 4006553 -1
AAA battery 4002084 -2
AA battery 4006432 - 4
Velcro 3/4" wide loop (self adhesive) 4000022 24
Velcro 3/4" wide hook (self adhesive) 4000023 24
Cable tie black 4005524 14
Power cord assembly 4006350 -1
Este manual sirve para los siguientes modelos
1
Otros manuales de Accesorios para chimeneas de Valor
Valor
Valor 546LFB ZC Portrait Ledgeview Front Manual de usuario
Valor
Valor L1 Series Manual de usuario
Valor
Valor 784EC Manual de usuario
Valor
Valor G3 Series Manual de usuario
Valor
Valor 725RTB Black Manual de usuario
Valor
Valor H5 Manual de usuario
Valor
Valor MADRONA Series Manual de usuario
Valor
Valor PORTRAIT BSK563 Manual de usuario
Valor
Valor Wonderfire BR417 Manual de usuario
Valor
Valor 1775 Manual de usuario
Valor
Valor Legend G3 739NGK Manual de usuario
Valor
Valor Retrofire Series Manual de usuario
Valor
Valor LT2 2700K Manual de usuario
Valor
Valor 715CVI Manual de usuario
Valor
Valor G3 Series Manual de usuario
Valor
Valor 738JL Manual de usuario
Valor
Valor 757 Manual de usuario
Valor
Valor G3.5 Series Manual de usuario
Valor
Valor 1170RGL Refl ective Glass Liner Set Manual de usuario
Valor
Valor LT1 2500K Manual de usuario
Manuales populares de Accesorios para chimeneas de otras marcas
Town & Country Fireplaces
Town & Country Fireplaces 22150051 Manual de usuario
Travis Industries
Travis Industries 33 DVI Manual de usuario
Superior
Superior ASD3628-TI Manual de usuario
pleasant hearth
pleasant hearth OFP28WG Manual de usuario
IHP
IHP Astria Series Manual de usuario
Firegear
Firegear FG-H-2110SS Manual de usuario
