UTC Fire and Security Edwards Signaling E-IDCWS Instrucciones de montaje

E-IDCWS Analog Dual Input Waterflow/

Supervisory Module Installation Sheet

Operation

The module is an analog addressable device used to connect

normally open waterflow alarm and supervisory initiating

device circuits (IDCs) to a control panel. This module is

designed for Class B circuit operation.

The device address is set using the two rotary switches located

on the front of the module. Two consecutive device addresses

are required. The second device address is automatically

assigned one number higher that the value set on the rotary

switches.

The module can operate in the following modes:

Table 1: Module operation

Operation

Device type description

Waterflow

Alarm latching delayed: Configures the module for use

with only nonretarded waterflow alarm switches. When

the NO input contact of an initiating device is closed, an

alarm is sent to the control panel, which after a 16

second time delay, generates an alarm signal.

Supervisory

Supervisory active nonlatching US marketplace

Supervisory active latching Canadian marketplace

Nonlatching: Configures the module for normally open

dry contact initiating devices. When the NO input

contact of an initiating device is closed, a supervisory

signal is sent to the control panel and the supervisory

condition is not latched at the module.

Latching: Configures the module for normally open dry

contact initiating devices. When the NO input contact of

an initiating device is closed, a supervisory signal is

sent to the control panel and the supervisory condition

is not latched at the module.

LED operation

The module provides a bicolor LED that shows its status.

Normal: Green LED flashes

Alarm/active: Red LED flashes

Installation

WARNINGS

• This module will not operate without electrical power. As

fires frequently cause power interruption, you should

discuss further safeguards with your local fire protection

specialist.

• This module does not support conventional smoke

detectors.

Note: The module is shipped from the factory as an assembled

unit; it contains no user-serviceable parts and should not be

disassembled.

To install the module:

1. Verify that all field wiring is free of opens, shorts, and

ground faults.

2. Make all wiring connections as shown in “Wiring.”

3. Set the module address as follows:

Use a screwdriver to adjust the two rotary switches on the

front of the module. Set the TENS rotary switch (0 through

12) for the 10s and 100s digit and the ONES rotary switch

for the 0 through 9 digit. For example: device address 21,

set TENS rotary switch to 2 and set the ONES rotary

switch to 1.

Refer to “Specifications” for available address numbers.

4 Mount the module on the electrical box using screws

provided with the electrical box.

5. Mount the wall plate on the module using #4-24 x 1/2 in.

(13 mm) self-tapping screws.

Figure 1: Module address

Insert

screwdriver

here

2 / 2 P/N 3101194 • REV 02 • REB 28JAN13

Figure 2: Module installation

Screw

4-24

screws

Module

Wall plate

Compatible

electrical box

Wiring

Wire in accordance with NFPA 72 and CAN/ULC-S524. Be

sure to observe the polarity of the wires as shown in the

diagram.

Specifications

Communication line voltage

Maximum 20.6 V peak-to-peak

Current

Standby

Activated

550 μA

725μA

Ground fault impedance

10 kΩ

Operating environment

Temperature

Humidity

32 to 120° F (0 to 49° C)

0 to 93% RH

Stor

age temperature range –4 to 140° F (–20 to 60° C)

Compatible electrical boxes

North American 4 inch square x

2-1/2 in. (64 mm) deep 2 gang box

Standard 4 in. square box 1-1/2 in.

(38 mm) deep

Wire size

12, 14, 16, or 18 AWG wire (2.5, 1.5,

1.0, or 0.75 mm2) (Sizes 16 and 18

AWG are preferred)

Device address

01 to 63 (64 point control panel)

01 to 126 (127 point control panel)

Initiating device circuit (IDC)

EOL resistor value

Max. circuit resistance

Max. circuit capacitance

47 kΩ, (P/N: EOL-47)

50 Ω (25 Ω per wire)

0.1 μF

Figure 3: Module wiring

Typical NO

Waterflow Switch

EOLR

kΩ

EOLR

kΩ

SUP.

Style B (Class B)

[1] [2] [4]

W/FLOW

Typical NO

Supervisory/

Tamper Switch

[3]

TB2 TB1

(+)

SLC

(+)

( )

From

device

To next

device SLC out (+)

SLC out

SLC in

SLC in (+)

( )

[1] Maximum 25 Ω resistance per wire

[2] Maximum 12 AWG (2.5 mm2) wire; minimum 18 AWG (0.75 mm2) wire

[3] Refer to the control panel technical reference manual for wiring specifications

[4] Maximum 10 VDC at 350 μA

5. All wiring is power-limited and supervised

6. This module will not support two-wire smoke detectors

Otros manuales de Unidad de control de UTC Fire and Security

UTC Fire and Security

UTC Fire and Security interlogix VR1520WDM Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Interlogix VT7420-2DRDT Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT14120 Guía

UTC Fire and Security

UTC Fire and Security interlogix VT6010-DRDT Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security KiddeFire Systems ARIES NETLink BACnet Manual de usuario

UTC Fire and Security

UTC Fire and Security interlogix VT2010 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT7820 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix TT3010 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Fenwal 35-63J Series Manual de usuario

UTC Fire and Security

UTC Fire and Security Interlogix NX-535N Manual de usuario

UTC Fire and Security

UTC Fire and Security interlogix VR1500 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VAD7010A Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT7420 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Interlogix VT72830-R3 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Interlogix VR1910 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT4010 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Interlogix NX-535N-V3 Manual de usuario

UTC Fire and Security

UTC Fire and Security interlogix VAR14120 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VR4930WDM Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security Interlogix VR1001 Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT1101M Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security interlogix VT9930WDM Instrucciones de instalación

UTC Fire and Security

UTC Fire and Security FenwalNET 8000-ML Manual de usuario

UTC Fire and Security

UTC Fire and Security interlogix VT7220 Instrucciones de instalación

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario