Uplift Desk MON054 Manual de usuario

Package Contents

Moontower Quad Monitor Arm

SKU: MON054

Dual Arm (qty 2)Adhesive Pad

Bolt-Through Mount

Clamp MountBase Cover

Pole Bolt-Through Plate

Cable Clip (qty 2)

Allen Wrenches

(set of three: 3mm, 5mm, 6mm)

Parts for

Bolt-Through assembly

M5x12 Screw (M-B) (qty 16)

M5 Washer (M-C) (qty 16)

M4x12 Screw (M-A) (qty 16)

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Step 3 (Clamp Method)

A. Slide the Clamp Mount onto the back of the desk-

top, then tighten the bolt of the clamp onto your

desktop using the knob.

B. If you chose the Clamp Method for mounting,

please skip the Bolt-Through Method (Steps 4-7)

and proceed with Step 8.

• Maximum monitor weight: 17.6 lb (each monitor)

• Recommended monitor size: up to 27”

• Desktop thickness compatibility: 0.4”-3.4” thick

There are two ways to attach the Moontower Quad Monitor Arm to your desktop. If you would like to attach it along the

back edge of your desktop, follow the Clamp Method instructions on this page. If you prefer to attach it through your desk-

top, follow the Bolt-Through Method instructions starting on page 2.

Step 1

Determine your mounting method. There are two

ways to attach the Moontower Quad Monitor Arm to

your desktop:

Clamp Method: If you would like to attach the monitor

arm along the back edge of your desktop, follow the

Clamp Method instructions (Steps 2 - 3).

Bolt-Through Method: If you prefer to attach the

monitor arm through your desktop, skip Steps 2 - 3

and follow the Bolt-Through Method instructions

(Steps 4 - 7).

Step 2 (Clamp Method)

Peel the adhesive backing off of the Adhesive Pad and

attach it to the bottom of the Clamp Mount as shown.

Align the Pad with the front edge of the Clamp Mount

base rst, then work to the back.

Clamp Method Bolt-Through Method

Clamp Method

Bolt-Through Method

Step 4 (Bolt-Through Method)

Ensure the desktop has a hole between 0.4’’ and 3.1’’

in diameter to use this option. Using a grommet hole

that is already in your desktop is acceptable, or you

can drill a 0.5” hole anywhere on your desktop.

Step 5 (Bolt-Through Method)

A. Use a small Phillips screwdriver to remove the oval

clamping plate from the top of the Bolt on the

Clamp Mount.

B. Remove the Bolt from the Clamp Mount.

Step 7 (Bolt-Through Method)

Slide the Bolt-Through Plate onto the Bolt from

Step 5 B.

Insert the Bolt through the hole in the desk from

below and align it with the threaded hole in the

bottom of the Bolt-Through Mount.

•

Make sure the two set screw holes in the cylinder

of the Bolt-Through Mount are facing the back

of the desk and one of the three holes on the

at part is pointing toward the front of the desk

so the Base Cover will be straight when it is at-

tached later.

Hand tighten the Bolt until the Bolt-Through Mount

is secure.

Step 6 (Bolt-Through Method)

Peel the adhesive backing off of the Adhesive Pad and

attach it to the bottom of the Bolt-Through Mount as

shown. Center the Pad within the circular edge of the

Bolt-Through Mount and press to adhere it.

0.4”

3.1”

Step 8

Using the 3mm Allen Wrench, loosen the set screws

around the cylinder on the Clamp Mount or Bolt-

Through Mount (Clamp Mount shown) so that they

do not obstruct the threads inside the cylinder.

B. Thread the Pole clockwise into the cylinder and

turn until it is tight and stops turning. Then re-tight-

en the set screws to secure the Pole in place.

Arm Assembly & Monitor Mounting

Step 12

Reminder: Maximum monitor weight per monitor for

the Moontower Quad Monitor Arm is 17.6 lb.

Lay your monitor face down on a clean surface or a

towel to prevent damage to your screen.

B. Test the M4x12 and M5x12 Screws in your monitor’s

screw holes to determine which is the right size for

your monitor.

Step 9

Slide the Base Cover over the Pole and snap it into

place on the Mount so that the three pegs inside the

Base Cover t into the three holes in the Mount.

Step 10

Slide the Cable Clip around the top of the Pole.

Step 11

A. Slide the rst Dual Arm onto the Pole to the ap-

proximate height you want and tighten using the

5mm Allen wrench.

B. Repeat Steps 10 and 11 with the remaining Cable

Clip and Dual Arm.

• You can adjust the heights as needed after your

monitors are attached. May require two people

to adjust when monitors are attached.

1/8”

Step 13

Determine whether your monitors have a 100 mm

VESA pattern, or a 75 mm VESA pattern. Each pat-

tern attaches in a different way to the Moontower

Quad Monitor Arm.

100 mm VESA pattern: If the holes are 100 mm apart

(just under 4”) from each other, proceed to Step 14.

75 mm VESA pattern: If the holes are 75 mm apart

from each other (just under 3”), skip Step 14 and pro-

ceed to Step 15.

100 mm

75 mm

100

100 mm

75 mm

100

100 mm VESA pattern 75 mm VESA pattern

Step 14 (100 mm VESA pattern)

A. Take two of the Screws from Step 12 and two

Washers and thread them into the top two holes

of your monitor leaving about a 1/8’’ gap between

the Washer and the back of your monitor.

B. Hold the monitor against the VESA Plate and slide

the two screws into the slots at the top of the

VESA Plate. Make sure the VESA Plate is between

the Washers and the monitor.

C. Before tightening the top Screws, start two more

Screws and Washers through the lower holes of

the VESA Plate and into the back of the monitor.

• Be careful to not dislodge the monitor from the

top two Screws while inserting the lower Screws!

D. Once all four Screws are started, tighten them all

with a Phillips screwdriver to secure the monitor in

place.

E. Repeat this step with the other monitors then skip

Step 15 and proceed to Step 16.

1/8”

Top

Step 15 (75 mm VESA pattern)

A. Have a friend hold the monitor up to the VESA

Plate and start four Screws from Step 13 and four

Washers through the VESA holes and into the

back of the monitor.

B. Then tighten all four Screws with a Phillips screw-

driver to secure the monitor in place.

C. Repeat this step with the other monitors.

Step 16

A. Plug in your monitors and run the cables through

the Arm Wire Clips and the Cable Clips on the

Pole.

B. The Cable Clips also have a place to hold the 5mm

& 6mm Allen Wrenches to keep them handy for

any future adjustments needed.

CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may

result in damage or personal injury. Retain manual for future reference.

CAUTIONS & WARNINGS

Height

The Dual Arms can be positioned anywhere along the

height of the Pole to accommodate your monitors’

sizes. Adjust the height of the arm (see Step 11) so that

the tops of your lower monitors are roughly at eye

level when you are in your seated or standing working

position.

Middle Hinge Swivel

Each Arm’s middle hinge has two swivel points.

Each swivel point can rotate right and left

within a range

180° (+/-90°).

Post Hinge Swivel

The Arm hinge that is closest to the Pole can each swiv-

el right or left within a range of 180° (+/-90°).

Monitor Rotation

The monitors can rotate at the VESA mount a full

360° allowing landscape or portrait viewing, provided

they don’t hit the monitor above or below it.

Adjustment Information

Monitor Tilt

Use a 6mm Allen wrench to loosen the screw and nut

behind the VESA mount to tilt your monitor forward

or backward within a range of 90° (+/-45°). Once in

the desired position, re-tighten the screw and nut to

secure the monitor in place.

Monitor Swivel

The monitors can swivel right and left 180° (+/-90°)

from the hinge closest to the monitor.

Notes

AI-MON054-1.0

512-614-3152

800-349-3839

[email protected]

upliftdesk.com

Work Better. Live Healthier

Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of the scope of delivery, even if the item is resold. This

guide is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other

published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.

SAVE THESE INSTRUCTIONS

Study this manual carefully. If this product is sold, please provide this

manual to the buyer, installers, or support personnel operating the product.

Tabla de contenidos

Otros manuales de Rack y soporte de Uplift Desk

Uplift Desk

Uplift Desk STR036 Manual de usuario

Uplift Desk

Uplift Desk MON001 Manual de usuario

Uplift Desk

Uplift Desk Crestview MON032 Manual de usuario

Uplift Desk

Uplift Desk Crestview MON033 Manual de usuario

Uplift Desk

Uplift Desk MON041 Manual de usuario

Uplift Desk

Uplift Desk ACC092 Manual de usuario

Uplift Desk

Uplift Desk MON051 Manual de usuario

Uplift Desk

Uplift Desk ACC301 Manual de usuario

Uplift Desk

Uplift Desk MON056 Manual de usuario

Uplift Desk

Uplift Desk MON021 Manual de usuario

Uplift Desk

Uplift Desk MON020 Manual de usuario

Uplift Desk

Uplift Desk CPU001 Manual de usuario

Uplift Desk

Uplift Desk MON034 Manual de usuario

Uplift Desk

Uplift Desk ACC302 Manual de usuario

Uplift Desk

Uplift Desk ACC095 Manual de usuario

Uplift Desk

Uplift Desk STR045 Manual de usuario

Uplift Desk

Uplift Desk MON041 Manual de usuario

Uplift Desk

Uplift Desk Zilker MON002 Manual de usuario

Uplift Desk

Uplift Desk MON053 Manual de usuario

Uplift Desk

Uplift Desk MON020 Manual de usuario

Uplift Desk

Uplift Desk MON001 Manual de usuario

Uplift Desk

Uplift Desk ACC055 Manual de usuario

Uplift Desk

Uplift Desk MON021 Manual de usuario

Uplift Desk

Uplift Desk ACC304 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario