Uplift Desk CPU001 Manual de usuario

Main UnitScrews

(qty 4)

Washers

(qty 4)

Mounting bracket

UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com

Package contents

E3 CPU Holder

CPU001

Step 1

Hold the Mounting bracket under your desk at the location you’ve

chosen, and mark the location of the four screw holes on your desktop.

*Consider placement:

Decide if you want the CPU Holder mounted to the front or side of your

desktop. Once installed, the CPU Holder will remain in this location and

will swivel 180° to allow you access to your CPU’s ports. Take a moment

to nd a place underneath your desk where you won’t have any ob-

structions when rotating the CPU Holder.

Step 2

Using a drill with a 1/8” bit, drill pilot holes where the four marks are

located. Drill no deeper than 1/2’’.

CAUTION: Do not drill through the desktop surface. Make sure

screws aren’t too long for your desktop thickness by holding the

screw up to the desktop’s edge. When using screws on a desktop

with a center-cut ergo edge, make sure that the screw is not close to

the ergo edge to avoid piercing the desktop with the screw. (see g. 1)

Step 3

Install the Mounting bracket with the four (4) Screws and four

(4) Washers.

Step 4

(a) Loosen the two knobs on the right and left side to adjust the height

of the Main unit to accommodate your CPU.

(b) Unlatch the four (4) Lock levers to adjust the width of the Main unit

to t your CPU.

Note: If any of the Lock levers are too tight to open, you

can loosen them slightly with a 2.5mm Allen wrench (not

included). Once you release the Lock levers, you can rotate

them counterclockwise to loosen them.

Next, expand the Main unit to its widest/tallest position.

CPU128/R01

g 1.

(a)

(b)

UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com

Step 5

Insert your CPU tower. Carefully reverse the process in Step 4, close the

width and height of the CPU Holder, tighten the knobs, and close the

Lock levers to secure it inside.

Step 6

Look at the top of your unit. Align the CPU Holder’s top bracket with

the Mounting bracket installed underneath your desktop.

Unscrew the set screws to allow the spring-release handle to be pulled

back to attach onto the Mounting bracket.

Step 7

First, lift up the CPU Holder and carefully guide the hooks on the CPU

Holder’s top bracket onto the Mounting bracket. (see gure 1)

Then, lift the other side of the unit to the Mounting bracket while hold-

ing open the spring release handle. Lift into place and let go of the han-

dle, locking it in. (Note: If the CPU is light enough, you may be able to

push upwards without needing to pull out the handle). Ensure that the

CPU Holder is rmly attached to the Mounting bracket.

IMPORTANT: Once secure, tighten the set screws on the handle, to pre-

vent any accidental releasing of the CPU Holder. (see gure 2)

!Read all instructions before installing. Failure to install properly may result in damage

or personal injury.

This guide is a component of the UPLIFT CPU Holder. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.com.

Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.

These instructions are subject to United States copyright law.

Adjustment Guide

The CPU Holder rotates 180 degrees.

180°

g 1.

g 2.

Tabla de contenidos

Otros manuales de Rack y soporte de Uplift Desk

Uplift Desk

Uplift Desk MON042 Manual de usuario

Uplift Desk

Uplift Desk STR017-SHT Manual de usuario

Uplift Desk

Uplift Desk Crestview MON032 Manual de usuario

Uplift Desk

Uplift Desk MON020 Manual de usuario

Uplift Desk

Uplift Desk Crestview MON031 Manual de usuario

Uplift Desk

Uplift Desk UPL021 Manual de usuario

Uplift Desk

Uplift Desk Motion-X 6-Pack Rack ACC052 Manual de usuario

Uplift Desk

Uplift Desk MON051 Manual de usuario

Uplift Desk

Uplift Desk MON020 Manual de usuario

Uplift Desk

Uplift Desk ACC305 Manual de usuario

Uplift Desk

Uplift Desk Zilker MON002 Manual de usuario

Uplift Desk

Uplift Desk Zilker Dual Monitor Arm Manual de usuario

Uplift Desk

Uplift Desk ACC304 Manual de usuario

Uplift Desk

Uplift Desk CPU128 Manual de usuario

Uplift Desk

Uplift Desk STR045 Manual de usuario

Uplift Desk

Uplift Desk MON001 Manual de usuario

Uplift Desk

Uplift Desk MON052 Manual de usuario

Uplift Desk

Uplift Desk ACC055 Manual de usuario

Uplift Desk

Uplift Desk MON021 Manual de usuario

Uplift Desk

Uplift Desk ACC302 Manual de usuario

Uplift Desk

Uplift Desk MON054 Manual de usuario

Uplift Desk

Uplift Desk ACC303 Manual de usuario

Uplift Desk

Uplift Desk ACC301 Manual de usuario

Uplift Desk

Uplift Desk Crestview MON033 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario