Uniden 4KTPD-MVF Manual de usuario

ProSeries

IP CAMERA

INSTALLATION GUIDE

4KTPD-MVF

4MTPD-MVF

4MTPD-2.8

2MTPD-VF

4MMD-2.8

2MMD-2.8

4MED-3.6

2MED-3.6

Irving, Texas

Issue 1, April 2018

2MTD-2.8

4KB-MVF

4MB-MVF

2MB-VF

4MB-3.6

2MB-3.6

Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal

purposes. Uniden expects consumer’s use of these products to be in compliance with all local,

state, and federal law. For further information on video surveillance and audio recording legal

requirements, please consult your local, state and federal ofcials.

Uniden constantly works on improving our products. This includes updating our documentation

with the latest rmware changes. Go to www.uniden.com to nd the latest version of all

documentation.

CONTENTS

OVERVIEW .............................................. 5

WHAT’S INCLUDED ........................................5

INSTALL CAMERAS ...................................... 5

INSTALLATION TIPS .......................................5

TAMPER-PROOF DOMED CAMERAS ..........................6

INSTALL MINI DOME CAMERA ..............................8

What’s Included...............................................8

Install Camera ................................................8

INSTALL EYEBALL DOME CAMERA .......................... 9

What’s Included...............................................9

Install Camera ................................................9

INSTALL TURRET DOME CAMERA ..........................10

What’s Included..............................................10

Install Camera ...............................................10

INSTALL LARGE BULLET CAMERAS......................... 11

What’s Included..............................................11

Install Camera ...............................................12

INSTALL SMALL BULLET CAMERAS.........................12

What’s Included..............................................12

Install Camera ...............................................13

CONNECTING THROUGH PC .............................. 13

USING DEVICEMANAGER TOOL ............................13

WEB ACCESS ............................................14

Set Security Levels ...........................................15

UNIDEN PROSERIES MOBILEPHONE CLIENT................ 16

SOFTWARE OPERATING ..................................16

Add device...............................................17

SPECIFICATIONS ....................................... 18

TAMPER-PROOF DOME CAMERAS .......................... 18

MINI AND EYEBALL DOME CAMERAS........................ 19

TURRET DOME AND LARGE BULLET CAMERAS............... 20

SMALL BULLET CAMERAS .................................21

COMPLIANCE .......................................... 22

FCC PART 15.............................................22

IC ......................................................23

THREE-YEAR LIMITED WARRANTY ........................ 23

INSTALLATION

OVERVIEW

Uniden’s IP cameras can be installed in either Uniden’s NVR or XVR surveillance systems.

TAMPER-

PROOF DOME

MINI DOME EYEBALL

DOME

TURRET

DOME

LARGE

BULLET

SMALL

BULLET

4KTPD-MVF 4MMD-2.8 4MED-3.6 2MTD-2.8 4KB-MVF 4MB-3.6

4MTPD-MVF 2MMD-2.8 2MED-3.6 4MB-MVF 2MB-3.6

4MTPD-2.8 2MB-VF

2MTPD-VF

WHAT’S INCLUDED

• IP camera

• Mounting template sticker

• Star-tipped Allen wrench

• 2-wire to 2.1mm barrell plug for optional 12V DC power input

• Installation screws and anchors

Network cable and power source are not included. SD cards are not included. If you

plan on using the Automatic Network Restoration feature in the NVR, you will need to

purchase an SD card.

INSTALL CAMERAS

INSTALLATION TIPS

• When selecting an outside location for your cameras, keep in mind that most cameras

are designed to operate between 14°F to 122°F (-10°C to 50°C) with a relative humidity

of up to 95%. Avoid installing cameras in direct sunlight, and consider wind chill and other

environmental factors, too.

• Mount the camera in an area that is visible, but out of reach. Route the wiring so it does not

interfere with power or telephone/cable lines and it should not be where it could be easily cut.

Create a plan for camera wire routing and for camera angle.

• Adjust the camera angle so that it covers an area with high trafc as needed. In “high-

risk” locations, have more than one camera cover the same area. This provides camera

redundancy if a vandal attempts to damage a camera.

• If you position cameras indoors, avoid pointing the camera at a glass window to see outside.

This may result in a bright white ring in the night vision image because the light from the night

vision LEDs may reect off the window glass.

Take the following placement suggestions under consideration:

• Cabling Distance From NVR to Camera. The video signal sent from the camera to the DVR

is reduced over distance. The maximum distance allowed is 330 feet (100 meters). A 60 foot

cable is included. If you need a cable longer than 60 feet, then use an RG59 cable (with

suitable connectors).

• Do not submerge any camera.

• Mounting. Ensure the camera is mounted on a stable surface which is capable of supporting 5

times the weight of the camera.

• Avoid direct exposure to the weather. Cameras which are weatherproof may be mounted

outside, such as under an eave or other overhang; however, the image will be affected by rain,

etc., landing on the lens. Do not allow direct sunlight to land on the lens.

1. With the DVR connected to the camera, hold it in the location where you want it mounted.

Check the display on the monitor to verify that the view from that location is acceptable.

2. Mount the camera(s) to the desired surface using the parts in the supplied mounting kit. If

mounting on drywall, use the drywall anchors supplied in the kit.

3. Adjust the camera to ensure that the camera has a satisfactory view of the area you would

like to monitor. Cameras have several adjustment points to provide maximum exibility when

setting the view angle.

TAMPER-PROOF DOMED CAMERAS

1. Remove the camera and accessory items from the box. Verify that all parts are there.

2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as

indicated on the sticker and install anchors and screws.

3. Unscrew the camera from the housing, allowing the camera to

separate from the housing and clear dome.

4. Connect the camera’s network cable tail to the house cabling through the 1” hole.

5. If you have a 4K TPD camera, connect the plugs from the

network cable tail to their appropriate cables.

When using an optional external power supply, the AC

socket outlet shall be installed near the equipment and be

easily accessible.

If installed outdoors, the cable and all cable connections

must be routed inside the wall.

White - Audio Out

Red - Audio In

Yellow - Video (BNC)

Black - Alarm In

Red - Alarm Out

RJ45

Red - 12VDC (optional)

Network

Activity

LEDs

PoE

2.1mm Barrel Adapter

NOTE: 12VDC power supply

not included

6. Align the camera base screw holes to the screws. Hang the

base onto the screws then slide the base along the screw lock

to secure.

Screw Hole

and Lock

7. Remove the protective lms from the inside and outside of the camera dome and clean the

dome with a microber cloth (not included) if available.

Do not use a paper towel to clean the camera lens or dome as it might leave

scratches.

8. Adjust the bracket to swivel the camera up to 175˚ on a

horizontal axis (orients the camera for top/bottom of frame).

Bracket

Swivel

Direction

Swivel

Direction

9. Loosen screw 1 and adjust the camera from 15 - 90˚ on a

vertical axis.

15˚ - 90˚

Screw 1

10.Loosen screw 2 to ne-tune the horizontal axis (+/- 30˚).

As you adjust the camera position, check it through the

NVR Preview screen.

Screw 2

11.Insert an SD card if needed.

SD Card Slot

Reset Button

12.Remove the dessicant packet from the sealed plastic envelope

and position it inside the camera.

13.Screw the housing back onto the camera base.

INSTALL MINI DOME CAMERA

What’s Included

• IP camera

• Mounting template sticker

• Star-tipped Allen wrench

• 2-wire to 2.1mm barrell plug for optional 12V DC power input

• Installation screws and anchors

• Dessicant package

Install Camera

1. Remove the camera and accessory items from the box. Verify that all parts are there.

2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as

indicated on the sticker and install anchors and screws.

3. Unscrew the camera from the housing, allowing the camera to

separate from the housing and clear dome.

4. Connect the camera’s network cable tail to the house cabling

through the 1” hole.

When using an optional external power supply, the AC

socket outlet shall be installed near the equipment and be

easily accessible.

If installed outdoors, the cable and all cable connections

must be routed inside the wall.

RJ45

Red - 12VDC (optional)

PoE

2.1mm Barrel Adapter

NOTE: 12VDC power supply

not included

5. Align the camera base screw holes to the screws. Hang the

base onto the screws then slide the base along the screw lock

to secure.

Screw Hole

and Lock

6. Remove the protective lms from the inside and outside of the camera dome and clean the

dome with a microber cloth (not included) if available.

Do not use a paper towel to clean the camera lens or dome as it might leave

scratches.

7. Adjust the collar to swivel the camera up to 175˚ on a horizontal

axis (orients the camera for top/bottom of frame).

As you adjust the camera position, check it through the

NVR Preview screen. Thumb

Control

Adjustable

collar

8. Insert an SD card if needed.

SD Card Slot

Reset Button

9. Remove the dessicant packet from the sealed plastic envelope

and position it inside the camera.

10.Align the tab on the housing with the slot on the camera base

for easier reassembly. Tighten screws.

INSTALL EYEBALL DOME CAMERA

What’s Included

• IP camera

• Mounting template sticker

• Star-tipped Allen wrench

• 2-wire to 2.1mm barrell plug for optional 12V DC power input

• Installation screws and anchors

• Dessicant package

Install Camera

1. Remove the camera and installation items from the box. Verify that all parts are there.

2. Hold the camera and sleeve steady and unscrew the ring from

the base.

Base

Ring

Camera

Sleeve

3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as

indicated on the sticker. Install the anchors.

4. Position the base on the template, aligning the screw holes to the anchors, and screw it into

position.

5. Connect the network cable tail to the house cabling through the

1” hole.

When using an optional external power supply, the AC

socket outlet shall be installed near the equipment and be

easily accessible.

If installed outdoors, the cable and all cable connections

must be routed inside the wall.

RJ45

Red - 12VDC (optional)

PoE

2.1mm Barrel Adapter

NOTE: 12VDC power supply

not included

6. Unscrew the hatch on the camera to insert an SD card if

needed.

7. Remove the dessicant packet from the sealed plastic envelope

and position it inside the camera.

8. Reassemble the camera, sleeve, and ring. Position the assembly onto the base and adjust

the camera to the correct viewing angle.

As you adjust the camera position, check it through the NVR Preview screen.

9. When the viewing angle is correct, tighten the ring to the base.

As you tighten the ring, keep adjusting the camera as needed.

INSTALL TURRET DOME CAMERA

What’s Included

• IP camera

• Mounting template sticker

• Star-tipped Allen wrench

• 2-wire to 2.1mm barrell plug for optional 12V DC power input

• Installation screws and anchors

• Dessicant package

Install Camera

1. Remove the camera and installation items from the box. Verify that all parts are there.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Uniden

Uniden

Uniden Guardian GC45 Manual de usuario

Uniden

Uniden UDW10055 Guía del usuario

Uniden

Uniden APPCAM23 Manual de servicio

Uniden

Uniden UDRC14 Manual de usuario

Uniden

Uniden AppCam 25HD Manual de usuario

Uniden

Uniden Guardian GC45 Manual de servicio

Uniden

Uniden AppCam 50HD Manual de usuario

Uniden

Uniden UDR444 Manual de usuario

Uniden

Uniden UDR744 Manual de usuario

Uniden

Uniden Guardian App Cam Solo Manual de usuario

Uniden

Uniden APP CAM 25 HDA Manual de usuario

Uniden

Uniden APPCAM23 Manual de usuario

Uniden

Uniden AppCam 4OPT Manual de usuario

Uniden

Uniden UDRC57HD Manual de usuario

Uniden

Uniden APPCAM23 Manual de usuario

Uniden

Uniden UDRC58HD Manual de usuario

Uniden

Uniden ULC58 Manual de usuario

Uniden

Uniden App Cam Solo+ Manual de usuario

Uniden

Uniden SOLO+ Manual de usuario

Uniden

Uniden App Cam 4K Bullet-S Manual de usuario

Uniden

Uniden APPCAM25HD Manual de usuario

Uniden

Uniden UDWC25 Manual de usuario

Uniden

Uniden Pro710NPTZC Manual de usuario

Uniden

Uniden UDS655 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario