Ultimaker 2 Extended Manual de usuario

Manual for the Ultimaker 2+

and Ultimaker Extended 2+

3D printers

Makers Lab

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Contents

Begin 3D printing ..........................................................................................................3

Removing and introducing material...............................................................................4

Introducing material ......................................................................................................9

Preparing build plate...................................................................................................12

Preparing 3D print in Cura 4.2.1 .................................................................................13

Begin printing..............................................................................................................17

3D print ready .............................................................................................................18

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Begin 3D printing

The manual is based on Cura version 4.2.1.

There is already material

in the printer and I will be

printing with this material.

Continue on page 12.

There is no material in the

printer. Continue on

page 9.

There is already material

in the printer, but I will not

be printing with this

material. Continue on

page 4.

There is already material

in the printer and I want to

remove it. Continue on

page 4.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Removing and introducing material

Switch on the printer with the switch

on the back to the left.

Twist the knob on front and select

MATERIAL.

Press the button.

Select CHANGE and press the

button.

The printing head will be heated up

to prepare for removing the

material.

The material will then be retracted

through the Bowden tube.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Remove the material from the

feeder.

Be certain that you also remove the

thin strands of residual material

from the Bowden tube which are

attached to the material.

Press the spool holder inside and

remove the spool from the spool

holder.

Do you only want to remove the

material?

In that case, switch off the printer

with the switch on the back to the

left.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Place another spool on the spool

holder. The material should run off

the spool on the bottom, on the

feeder side.

Snip off the end, making a level cut.

Select READY and press the

button.

Select PLA and press the button.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

The printer head will heat up.

Wait until the menu ‘Insert new

material from the…..’ appears.

Now insert material into the bottom

of the feeder until the feeder grasps

the material. If necessary, you can

press up the switch on the side.

Select READY and press the

button.

The material will be led through the

Bowden tube.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Wait until the material leaving the

nozzle is the same colour as the

material that was introduced.

Select READY and press the

button.

Select ‘Return’ and press it twice.

You have now returned to the Start

menu.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

Introducing material

Switch on the printer with the switch

on the back to the left.

Place a spool on the spool holder.

The material should run off the

spool on the bottom, on the feeder

side.

Snip off the end, making a level cut.

Select MAINTENANCE and press

the button.

Select ADVANCED and press the

button.

Select ‘Insert material’ and press

the button.

Ver. 01NL okt19

MAKERS LAB

Benno Premselahuis

Rhijnspoorplein 1

1091

GC Amsterdam

The printer head will heat up.

Wait until the menu ‘Insert new

material from the…..’ appears.

Now insert material into the bottom

of the feeder until the feeder grasps

the material. If necessary, you can

press up the switch on the side.

Select READY and press the

button.

The material will be led through the

Bowden tube.

Otros manuales para 2 Extended

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de Ultimaker

Ultimaker

Ultimaker 3 Extended Guía

Ultimaker

Ultimaker 3 Extended Guía

Ultimaker

Ultimaker METHOD XL Manual de usuario

Ultimaker

Ultimaker S3 Guía de instalación

Ultimaker

Ultimaker S5 Material Station Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker S5 Material Station Manual de usuario

Ultimaker

Ultimaker S3 Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker ORIGINAL+ Manual de usuario

Ultimaker

Ultimaker EXTRUSION UPGRADE Manual de usuario

Ultimaker

Ultimaker S5 Material Station Manual de usuario

Ultimaker

Ultimaker 3 Extended Guía

Ultimaker

Ultimaker S3 Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker 3 Extended Manual de usuario

Ultimaker

Ultimaker 2 Go Manual de usuario

Ultimaker

Ultimaker EXTRUSION UPGRADE Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker Heated Bed Upgrade Kit Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker 2 Extended Manual de usuario

Ultimaker

Ultimaker UM2 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario