Ubiquiti ES-48-500W Manual de usuario
Managed PoE+ Gigabit Switch
with SFP+
Models: ES-48-500W, ES-48-750W
Introduction
Thank you for purchasing the Ubiquiti Networks® EdgeSwitch™.
This Quick Start Guide is designed to guide you through
installation and also includes warranty terms.
The hardware description and installation instructions are the
same for both models, ES‑24‑250W and ES‑24‑500W.
Package Contents
EdgeSwitch
Managed PoE+ Gigabit Switch
with SFP+
Models: ES-48-500W, ES-48-750W
Power Cord Mounting Screws
(#10‑32 x 5/8", Qty. 4)
Cage Nuts
(#10‑32 x 5/8", Qty. 4)
Quick Start
Guide
TERMS OF USE: All Ethernet cabling runs must use CAT6A (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.
Installation Requirements
• Phillips screwdriver
• Standard‑sized, 19" wide rack with a minimum of 1U height
available
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit: www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock,
do not expose the EdgeSwitch to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeSwitch itself should be housed inside a
protective enclosure.
Hardware Overview
Front Panel LEDs
System
RJ45: PoE RJ45: Speed/Link/Act
SFP: Speed/Link/Act
SFP+: Speed/Link/Act
LED State Status
System
White Ready for Use
Blue
Bootup in Progress
Flashing Indicates Reset to
Factory Defaults
RJ45 1‑48
PoE
Off No PoE
Amber IEEE 802.3af/at
Green 24V Passive
Speed/
Link/
Act
Off No Link
Amber Link Established at 10/100Mbps
Flashing Indicates Activity
Green Link Established at 1000Mbps
Flashing Indicates Activity
SFP+ 1‑2
Speed/
Link/
Act
Off No Link
Green Link Established at 1Gbps
Flashing Indicates Activity
White Link Established at 10Gbps
Flashing Indicates Activity
SFP 1‑2
Speed/
Link/
Act
Off No Link
Green Link Established at 1Gbps
Flashing Indicates Activity
Front Panel Button
Reset
Button Description
Reset
There are two methods to reset the
EdgeSwitch to factory defaults:
Runtime Reset (Recommended)
The EdgeSwitch should be running after
bootup is complete, and the System LED
is white. Press and hold the Reset button.
The EdgeSwitch will reboot, and the System
LED becomesblue after three seconds.
Continue to hold the Reset button for
about 15seconds until the System LED
flashes blue for two seconds. This indicates
that the EdgeSwitch has reset to its
factorydefaults.
Power‑on Reset
1. Disconnect the Power Cord from the
EdgeSwitch.
2. While connecting the Power Cord to
the EdgeSwitch, hold the Reset button
for about 15seconds until the System
LED flashes blue for two seconds. This
indicates that the EdgeSwitch has reset
to its factory defaults.
Front Panel Ports
RJ45 1-48
SFP 1-2
SFP+ 1-2
Port Description
RJ45 1‑48 RJ45 ports support Power over Ethernet (PoE)
and 10/100/1000 Ethernet connections.
SFP+ 1‑2 Hot-swappable SFP+ ports support 1/10Gbps
connections.
SFP 1‑2 Hot‑swappable SFP ports support 1 Gbps
connections.
Back Panel
CONSOLE
Mounting Holes
Power
Mounting Holes
Console
Port Description
Console
RJ45 serial console port for Command
Line Interface (CLI) management. Use an
RJ45‑to‑DB9, serial console cable, also
known as a rollover cable, to connect
the Console port to your computer. Then
configure the following settings as needed:
• Baud rate 115200
• Data bits 8
• Parity NONE
• Stop bits 1
• Flow control NONE
Note: There are fans and ventilation holes on the sides of
the EdgeSwitch.
*640-00118-08*
640-00118-08
Hardware Installation
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
1. Connect the Power Cord to the Power port of the
EdgeSwitch.
2. Attach the EdgeSwitch to the rack using the four Mounting
Screws. (If the rack has square slots, then use the Cage Nuts
with the Mounting Screws.)
3. Connect the other end of the Power Cord to a power outlet.
Connecting Ethernet
1. Connect an Ethernet cable from your computer or host
system to any port of the EdgeSwitch.
2. Connect Ethernet cables from the Ethernet ports of your
devices to the other numbered ports of the EdgeSwitch.
Note: The PoE settings for ports 1-48 are set to
PoE+auto by default, so 802.3af/at devices can
be plugged in and automatically receive PoE. For
instructions on how to enable 24V passive PoE, refer
to the Configuring PoE Settings section.
Using SFP+ and SFP Ports
These ports support the specified module types at the
following speeds:
Ports SFP+ Module Type SFP Module Type
SFP+ 1‑2 10 Gbps 1 Gbps
SFP 1‑2 (Not supported) 1 Gbps
To use an SFP+ or SFP port:
1. Remove the protective plug covering the SFP+ or SFP port.
2. Plug a compatible fiber module into the SFP+ or SFP port.
1000MbpsSM/SC20KM DDM
Tx1550nm/Rx1310nm
3. Connect the appropriate SFP+ or SFP fiber optic cable to
the fiber module. Then connect the other end of the cable
to another fiber device.
For information about compatible fiber SFP+ or SFP modules,
visit: community.ubnt.com/edgemax
Accessing the Configuration Interface
The EdgeSwitch is set to DHCP by default, so it will try to
automatically obtain an IP address. If that fails, then it will use
the default fallback IP address, 192.168.1.2. Proceed to the
appropriate section, DHCP or Fallback IP Address:
DHCP
Use one of the following methods:
• Set up the DHCP server to provide a specific IP address to
the EdgeSwitch based on its MAC address (on the label).
• Let the EdgeSwitch obtain an IP address and then check the
DHCP server to see which IP address was assigned.
To log in, follow these steps:
1. Launch your web browser. Type the appropriate IP address
in the address field. Press enter (PC) or return (Mac).
2. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.
The EdgeSwitch Configuration Interface will appear. Customize
additional settings as needed. For more information on PoE
configuration, refer to the Configuring PoE Settings section.
Otros manuales para ES-48-500W
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Ubiquiti
Ubiquiti
Ubiquiti TS-5-POE ToughSwitchPoE Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 12 Fiber Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch ES-16-150W Manual de usuario
Ubiquiti
Ubiquiti 0810354023262 Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch Lite ES-24-Lite Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 8 Manual de usuario
Ubiquiti
Ubiquiti US-8-150W Manual de usuario
Ubiquiti
Ubiquiti UniFi Switch Flex Manual de usuario
Ubiquiti
Ubiquiti mFi-LD Manual de usuario
Ubiquiti
Ubiquiti USW-Pro-24 Manual de usuario
Ubiquiti
Ubiquiti TS-16-CARRIER Manual de usuario
Ubiquiti
Ubiquiti UniFi USW-24-POE Manual de usuario
Ubiquiti
Ubiquiti USW-48-POE Manual de usuario
Ubiquiti
Ubiquiti US-16-XG Manual de usuario
Ubiquiti
Ubiquiti UniFi USW-24-POE Manual de usuario
Ubiquiti
Ubiquiti NanoSwitch N-SW Manual de usuario
Ubiquiti
Ubiquiti UniFi Switch 48-500W Manual de usuario
Ubiquiti
Ubiquiti TS-5-POE ToughSwitchPoE Manual de usuario
Ubiquiti
Ubiquiti US-XG-6POE Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 8 150W Manual de usuario
