Ubiquiti EdgeSwitch ES-16-150W Manual de usuario
Managed PoE+ Gigabit Switch
with SFP
Model: ES-16-150W
Introduction
Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®.
This Quick Start Guide is designed to guide you through the
installation and also includes the warranty terms.
Package Contents
EdgeSwitch ES-16-150W
Power Cord Mount Brackets
(Qty. 2)
Bracket Screws
(Qty. 8)
Mounting Screws
(Qty. 4)
Cage Nuts
(Qty. 4)
Rubber Feet
(Qty. 4)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the professional
installer’s responsibility to follow local country regulations, including operation within legal
frequency channels, output power, indoor cabling requirements, and Dynamic Frequency
Selection (DFS) requirements.
Installation Requirements
• Phillips screwdriver (for rack or wall mounting)
• Standard-sized, 19" wide rack with a minimum of 1U height
available (for rack mounting)
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock,
do not expose the switch to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeSwitch itself should be housed inside a
protective enclosure.
Hardware Overview
Front Panel Ports
RJ45 1-16 SFP 1-2
Port Description
RJ45 1-16 RJ45 ports support 10/100/1000 Ethernet
connections.
SFP 1-2 Hot-swappable SFP ports support 1 Gbps
connections.
Front Panel LEDs
System
System LED
Note: The System LED functionality has been updated
with firmware v1.8.0. We recommend that you update
the EdgeSwitch to the latest firmware.
State Status
Flashing White Bootup in progress.
White Ready for use, not connected to Ubiquiti®
Network Management System (UNMS™).
Blue Ready for use, connected to UNMS.
Steady Blue
with Occasional
Flashing
Ready for use, unable to connect to
UNMS, check connection to UNMSserver.
Quickly Flashing
Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
You can use the EdgeSwitch Configuration Interface or UNMS
to manage your device. UNMS lets you configure, monitor,
upgrade, and back up your devices using a singleapplication.
Get started at www.unms.com
RJ45:
PoE
RJ45:
Speed/Link/Activity
SFP:
Speed/Link/Activity
RJ45 LEDs
LED State Status
PoE
Off No PoE
Amber IEEE 802.3af/802.3at
Green 24V Passive
Speed/
Link/
Activity
Off No Link
Amber Link Established at 10/100 Mbps
Amber
Flashing Link Activity at 10/100 Mbps
Green Link Established at 1000 Mbps (1 Gbps)
Green
Flashing Link Activity at 1000 Mbps (1Gbps)
SFP LEDs
LED State Status
Speed/
Link/
Activity
Off No Link
Green Link Established at 1 Gbps
Green
Flashing Link Activity at 1Gbps
Front Panel Button
Reset
Button Description
Reset
There are two methods to reset the
EdgeSwitch to factory defaults:
Runtime Reset (Recommended)
The EdgeSwitch should be running after
bootup is complete, and the System LED
is white. Press and hold the Reset button.
The EdgeSwitch will reboot, and the System
LED becomesblue after three seconds.
Continue to hold the Reset button for
about 15seconds until the System LED
flashes blue for two seconds. This indicates
that the EdgeSwitch has reset to its
factorydefaults.
Power-on Reset
1. Disconnect the Power Cord from the
EdgeSwitch.
2. While connecting the Power Cord to
the EdgeSwitch, hold the Reset button
for about 15seconds until the System
LED flashes blue for two seconds. This
indicates that the EdgeSwitch has reset
to its factory defaults.
Back Panel Console Port
Console
Port Description
Console
RJ45 serial console port for Command
Line Interface (CLI) management. Use an
RJ45-to-DB9, serial console cable, also
known as a rollover cable, to connect
the Console port to your computer. Then
configure the following settings as needed:
• Baud rate 115200
• Data bits 8
• Parity NONE
• Stop bits 1
• Flow control NONE
Hardware Installation
The EdgeSwitch can be placed on a horizontal surface,
mounted in a rack, or mounted on a wall.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Place the Rubber Feet on the bottom of the EdgeSwitch if you
do not plan to mount it. For rack or wall mounting, follow the
appropriate steps:
Rack Mounting
1. Attach the Mount Brackets to the EdgeSwitch using the
eight Bracket Screws, positioning the brackets as shown
below.
2. Attach the EdgeSwitch to the rack using the four Mounting
Screws. (If the rack has square slots, then use the Cage Nuts
with the Mounting Screws.)
Wall Mounting
1. Attach the Mount Brackets to the EdgeSwitch using the
eight Bracket Screws, positioning the brackets as shown
below.
2. Secure the EdgePower to the wall using the appropriate
fasteners and anchors (not included) for the wall.
Connecting Power
1. Connect the Power Cord to the Power port of the
EdgeSwitch.
2. Plug the Power Cord into a power outlet.
Otros manuales para EdgeSwitch ES-16-150W
1
Tabla de contenidos
Otros manuales de Cambiar de Ubiquiti
Ubiquiti
Ubiquiti UniFi US-48-750W Manual de usuario
Ubiquiti
Ubiquiti UniFi US-48-500W Manual de usuario
Ubiquiti
Ubiquiti UniFi Switch 24 US-24-250W Manual de usuario
Ubiquiti
Ubiquiti US-XG-6POE Manual de usuario
Ubiquiti
Ubiquiti USW--Pro--48 Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 10 XP Manual de usuario
Ubiquiti
Ubiquiti UniFi USW-24-POE Manual de usuario
Ubiquiti
Ubiquiti ES-48-500W Manual de usuario
Ubiquiti
Ubiquiti UniFi USW-Industrial Manual de usuario
Ubiquiti
Ubiquiti UniFi USW-Industral Guía
Ubiquiti
Ubiquiti US-XG-6POE Manual de usuario
Ubiquiti
Ubiquiti USW-24 Manual de usuario
Ubiquiti
Ubiquiti unifi switch 8 Manual de usuario
Ubiquiti
Ubiquiti USW-Industrial Manual de usuario
Ubiquiti
Ubiquiti UniFi Switch 48-500W Manual de usuario
Ubiquiti
Ubiquiti POE-50-60W Manual de usuario
Ubiquiti
Ubiquiti US-8-150W Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 48 LITE Manual de usuario
Ubiquiti
Ubiquiti TS-5-POE ToughSwitchPoE Manual de usuario
Ubiquiti
Ubiquiti EdgeSwitch 48 Manual de usuario
