Ubiquiti AirFiber 60 Manual de usuario

airFiber®60 GHz Radio

with 5 GHz Backup

Model: AF60

• Package Contents

• Installation Requirements

• Hardware Overview

• Installation Overview

• airFiber 60 Configuration

• UNMS Management

• Alignment

• Installer Compliance Responsibility

• Specifications

• Safety Notices

• Electrical Safety Information

• Limited Warranty

• Compliance

• Online Resources

Package Contents

Dish Main Arm Support Arms

(Qty. 2)

Mounting

Bracket

Screw U-Clamp

Flange Nuts

(Qty. 2)

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord

Installation Requirements

• Clear line of sight between airFiber AP and station

• Clear view of the sky for proper GPS operation

• Vertical mounting orientation

• Mounting point:

• At least 1 m below the highest point on the structure

• For tower installations, at least 3 m below the top of

thetower

• Outdoor, shielded Category 6 (or above) cabling and

shielded RJ45 connectors are required for all wired Ethernet

connections.

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP-G2, one near the airFiber radio and the other

at the entry point to the building. The ETH-SP-G2 will absorb

power surges and safely discharge them into the ground.

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory

codes.

LAN

≤ 1m

Hardware Overview

LEDs

LED State Status

GPS Blue

The LED will light blue when the

GPS signal strength is sufficient. This

requires a minimum of four GPS

satellite connections.

60G Blue The LED will light blue when the

60GHz link is active.

5G Blue The LED will light blue when the

5GHz link is active.

LAN

Blue

The LED will light steady blue when

an active Ethernet connection is

made to the Ethernet port and flash

when there is activity.

LED State Status

Power

Flashing

White Bootup in progress.

White

Ready for use, not connected to

Ubiquiti® Network Management

System (UNMS™). See “UNMS

Management”.

Blue Ready for use, connected to UNMS.

Steady

Blue with

Occasional

Flashing

Ready for use, unable to connect

to UNMS, check connection to

UNMSserver.

Quickly

Flashing

Blue

Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

Ports

6PoE IN Gigabit PoE port for handling all user traffic and

powering the device. Default IP address: 192.168.1.20.

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the device is

poweredon.

Installation Overview

We recommend that you configure your airFiber radio before

site installation.

airFiber 60 Configuration

Connecting Power over Ethernet

Configuring the Settings

2. Configure the Ethernet adapter on your computer with a

static IP address on the 192.168.2.x subnet.

3. Launch your web browser. In the address field, type:

http://192.168.1.20

Then press enter (PC) or return (Mac).

http://192.168.1.20

4. Enter ubnt in the Username and Password fields. Select

your Country and Language. You must agree to the Terms of

Use to use the product. Click Login.

5. Click the icon.

6. Configure the following settings:

a. For one airFiber radio, enable Access Point mode. For

the other airFiber radio (the Station), keep Access Point

disabled.

b. Enter a name in the SSID field. This should be the same

on both the AP and the Station.

c. In the WPA2 Preshared Key field, enter a combination of

alphanumeric characters (0-9, A-Z, or a-z).

Note: The key is an alphanumeric password

between 8 and 63 characters long.

7. Click Save Changes.

8. Configure each airFiber radio with a unique IP address:

a. Click the icon.

b. Review the Network settings to ensure that the AP and

Station each have a unique IP address. Each can get its

IP address via DHCP, or use the fallback IP address.

• DHCP By default DHCP client is enabled; if there is a

DHCP server on your network, the airFiber radio will

receive its address via DHCP.

• Fallback IP If you use the fallback IP address on one

radio, you must change the IP Address setting on the

other radio. The fallback IP address is: 192.168.1.20

c. Click Save Changes.

Repeat the instructions in the “airFiber 60 Configuration”

section on the other airFiber radio.

UNMS Management

You can manage your device using UNMS, which lets you

configure, monitor, upgrade, and back up your devices using a

singleapplication. Get started at www.unms.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Ubiquiti

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Manual de usuario

Ubiquiti

Ubiquiti ES-10X Manual de usuario

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manual de usuario

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Manual de usuario

Ubiquiti

Ubiquiti UniFi US-48-500W Manual de usuario

Ubiquiti

Ubiquiti RD-3G26 Manual de usuario

Ubiquiti

Ubiquiti NanoBeam M Manual de usuario

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Manual de usuario

Ubiquiti

Ubiquiti USW-24 Manual de usuario

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Manual de usuario

Ubiquiti

Ubiquiti UBB Manual de usuario

Ubiquiti

Ubiquiti AM-5AC21-60 Manual de usuario

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam M5 PBE-M5-400 Manual de usuario

Ubiquiti

Ubiquiti M900 Manual de usuario

Ubiquiti

Ubiquiti Rocket R5AC-Lite Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoBridge M NBM3 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam AC Gen 2 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam M5 Manual de usuario

Ubiquiti

Ubiquiti Nano G Manual de usuario

Ubiquiti

Ubiquiti UF-Instant Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Manual de usuario

Ubiquiti

Ubiquiti RocketDish RD-5G30 Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoStationM2 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario

Ubiquiti airFiber 60 Manual de usuario

Manuales populares de Hardware de red de otras marcas