Ubiquiti PowerBeam PBE-5AC-500-ISO Manual de usuario

5 GHz airMAX®ac Bridge with

500 mm RF Isolated Reflector

Model: PBE-5AC-500-ISO

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®acISO. This Quick Start Guide is designed to

guide you through installation and includes warranty terms.

Package Contents

Reflector Radome Antenna Feed Rear Housing

Mounting

Bracket

Adjustment

Bracket

Hex Bolts with Washers

(Qty. 4)

Pole Clamp

(Qty. 2)

Carriage Bolts

(Qty. 4)

Flange Nuts

(Qty. 4)

Screws with Washers

(Qty. 4)

Washers

(Qty. 4)

5 GHz airMAX®ac Bridge with

500 mm RF Isolated Reflector

Model: PBE-5AC-500-ISO

Nylon Insert

Lock Nuts

(Qty. 4)

Gigabit PoE

(24V, 0.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release Button Slot

Mounting Bracket

Release Button

Reflector

Alignment Pins

Reset Button

Radome

Technology

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the device is

poweredon. Alternatively, the device may be reset remotely

via a Reset button located on the bottom of the Gigabit

PoE adapter.

Release Button After you assemble the device, check the

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS®, you can modify the threshold

value for the wireless signal strength LEDs on the

Wireless tab under Signal LED Thresholds. Each LED

will light when the wireless signal strength is equal

to or greater than the LED’s threshold value. The

default threshold values for these LEDs are shown

below:

-65 dBm -73 dBm -80 dBm -94 dBm

Application Examples

The PowerBeam mounted outdoors with the Reflector

installed provides directional outdoor coverage (gain is

reflector‑dependent).

The PowerBeam mounted outdoors without the Reflector

installed provides outdoor‑to‑indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Mounting Bracket into

the slots of the Reflector. Rotate the Mounting Bracket

counterclockwise until the alignment holes in the dish and

bracket align with each other.

2. For added support in high‑wind environments, insert four

Screws with Washers into the holes in the Reflector and

Mounting Bracket, and secure each screw with a Washer

and a Nylon Insert Lock Nut.

Mounting Bracket Reflector

3. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Mounting Bracket. Push the Rear

Housing into the Mounting Bracket.

4. View the Reflector from the front. Ensure that the three

hooks (indicated below) of the Rear Housing are fully

engaged with the inner wall of the Reflector and locked

into place.

IMPORTANT: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

5. Push in the sides of the Cable Door and detach it from the

Rear Housing.

6. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release

Button

Bottom View

7. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re‑attach the Cable Door to the

RearHousing.

8. Attach the Pole Clamps to the Adjustment Bracket.

a. Hold the Adjustment Bracket with its clamps facing you

and the Elevation Indicators towards the top.

b. Insert the Carriage Bolts through the holes of the

Adjustment Bracket.

c. Place the Pole Clamps on the bolts on one side of the

bracket by sliding the hole of the clamp over the bolt.

d. Place one Flange Nut on each bolt.

Elevation

Indicator

9. Mount the Adjustment Bracket on the pole and secure it.

a. Place the Adjustment Bracket against the pole.

b. Slide the slot of each Pole Clamp over the adjacent

Carriage Bolt.

c. Tighten the Flange Nuts of the bolts to 25 N · m to secure

the Adjustment Bracket to the pole.

25 N ·m

Note: The mounting assembly can accommodate a

Ø 40 ‑ 80 mm pole.

Otros manuales para PowerBeam PBE-5AC-500-ISO

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Ubiquiti

Ubiquiti

Ubiquiti airFiber 60 Manual de usuario

Ubiquiti

Ubiquiti RD-3G26 Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoBridge M NBM3 Manual de usuario

Ubiquiti

Ubiquiti UBB Manual de usuario

Ubiquiti

Ubiquiti UF-OLT-4 Manual de usuario

Ubiquiti

Ubiquiti Rocket R5AC-Lite Manual de usuario

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manual de usuario

Ubiquiti

Ubiquiti ER-4 Manual de usuario

Ubiquiti

Ubiquiti UFiber OLT Manual de usuario

Ubiquiti

Ubiquiti NanoBeam M Manual de usuario

Ubiquiti

Ubiquiti M900 Manual de usuario

Ubiquiti

Ubiquiti ES-10X Manual de usuario

Ubiquiti

Ubiquiti mFi mPort Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Manual de usuario

Ubiquiti

Ubiquiti airVision-C Manual de usuario

Ubiquiti

Ubiquiti UniFi US-24-250W Manual de usuario

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Manual de usuario

Ubiquiti

Ubiquiti R5AC-PTP Manual de usuario

Ubiquiti

Ubiquiti USW-24 Manual de usuario

Ubiquiti

Ubiquiti UniFi US-48-500W Manual de usuario

Ubiquiti

Ubiquiti U-Installer Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoStationM2 Manual de usuario

Ubiquiti

Ubiquiti UBB Manual de usuario

Ubiquiti

Ubiquiti PBM3 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario