Tuff Tonneaus 10522 Guía de instalación

TONNEAU FITTING INSTRUCTION

Isuzu D-Max Dual Cab With Head Board

Jul 2012 to Current

Part number: 10522

Package includes

 1 X Tonneau cover  2 x Bar Brackets (300474)

 1 x Tonneau Support Bar (300516)  28 x Rivets (300482)

 1 x Rope Track 1253mm (With Shim)  1 x Lock Bracket

 1 x Support Bar Sheath  16 x Rope Buttons (300473)

 1 x Fitting Instructions  2 x Dowel

 1 x Warranty Card  4 x M8 Bolt (S 0050)

 1 x LH Front cnr seal plate A300118

 1 x RH Front cnr seal plate A300119

2 | P a g e

Table of Contents

1. TONNEAU COVER FITTING .............................................................................................................. 3

1.1 BASIC TOOL REQUIRED ................................................................................................................. 3

1.2 TONNEAU COVER INSTALLATION PROCEDURE ............................................................................ 3

2. TONNO LOCK ................................................................................................................................... 6

2.1 BASIC TOOL REQUIRED ................................................................................................................. 6

2.2 TONNO LOCK CONTENTS .............................................................................................................. 6

2.3 FITTING TONNO LOCK ................................................................................................................... 6

3. MULTI FIT SUPPORT BAR ................................................................................................................ 7

2.1 BASIC TOOL REQUIRED ................................................................................................................. 7

2.2 MULTI FIT SUPPORT BAR CONTENTS ........................................................................................... 7

2.3 FITTING MULTI FIT BAR ................................................................................................................ 7

3 | P a g e

1.1.

1. TONNEAU COVER FITTING

TONNEAU COVER FITTINGTONNEAU COVER FITTING

TONNEAU COVER FITTING

NOTE

Read entire instructions prior to start.

1.1 BASIC TOOL REQUIRED

1.1 BASIC TOOL REQUIRED1.1 BASIC TOOL REQUIRED

1.1 BASIC TOOL REQUIRED

Drill, 4mm Drill Bit, Rivet Gun, Marking Pencil / Pen

1.2 TONNEAU COVER

1.2 TONNEAU COVER 1.2 TONNEAU COVER

1.2 TONNEAU COVER INSTALLATION PROCEDURE

INSTALLATION PROCEDUREINSTALLATION PROCEDURE

INSTALLATION PROCEDURE

NOTE Remove swarf and a ly the rovided Rust Inhibitor to all drilled holes rior to

riveting. Read entire instructions rior to start.

1. To attach seal plates, remove the top bolt on each side of the inside edge that secures the head

board. Place the seal plate against the inside of the head board and relace bolt. DO NOT

TIGHTEN YET.

2. Align the seal plate so the top surface sits level with the top front edge of the tub. With 4mm

drill bit, drill a hole in the front face of the tub through the existing hole in the seal plate on

each side. DO NOT RIVET YET.

3. Remove seal plate and clean swarf from the tub and seal plate. Apply a bead of silicone to the

back of the seal plate. Reposition seal plate against the front face of the tub. Insert 4mm rivet

and rivet into place. Tighten bolts in head board.

4. Place one piece of dowel in each end of the rope track. Rest rope track and dowel on the top

edge of the seal plates. Ensure the flat side of the rope track is the surface positioned against

the tub face. See F gure 1.

5. Drill 4mm hole through each of the holes in the rope track into the front edge of the tub. Place

a 4mm rivet in each hole as it is drilled. DO NOT RIVET YET. Once all holes have been drilled,

remove the rivets, rope track and dowels.

6. Apply a bead of clear silicone along the centre of the front edge of the rope track (the side that

contacts the tub).

7. Rivet the aluminium rope track into position.

8. With the pencil mark the inside edge on each side of the tub at 740mm from the inside front

face of tub towards the rear on each side. Centrally locate the bar bracket over this position

and align the top of the bar bracket 10mm down from the top edge of the tub and drill and

rivet bracket into place. See F gure 2. Repeat for other side of tub. Fit tonneau support bar to

bar brackets.

4 | P a g e

Slide the front of the tonneau cover through the alumin

um rope track section.

10. Ensure tonneau s centred. To fit the rope buttons to the tub, start with the ta lgate, vertically

line up each button to each bunji loop starting from the centre bunji loops. The height for the

buttons on the tailgate is 410mm UP from the bottom edge of the tailgate. Work from the

centre out, alternating from side to side. Attach each bunji to the button as it is fitted.

11. To fit the rope buttons to the sides, vertically line up each button to each bunji loop starting

from the rear bunji loop, alternating from side to side working towards the front. The height for

the side rope buttons are all measured down from the TOP INSIDE EDGE of the tub. For the

rear button measure 160mm, 165mm for the second button from the rear, and 170mm for the

next two buttons. For the button closest to the front of the tub measure 175mm down and

25mm back from the front edge of the tub. Attach each bunji to the button as it is fitted.

NOTE: All measurements are to be taken from the TOP INSIDE EDGE of the tub.

12. To fit Velcro to the tub release the front bunji on each side. Fold the cover back to reveal the

hook side Velcro (attached to the loop side on the cover). Peal the backing from the velcro and

fold back onto the top edge of the tub. ALLOW 30 MINUTES FOR THE VELCRO TO ADHERE.

5 | P a g e

F gure 2: Placement of

bar bracket

F gure 1: Placement of

aluminium rope track.

Ensure channel is above

the tub’s top edge.

10mm down

from top edge

of tub

740mm

6 | P a g e

2.2.

2. TONNO LOCK

TONNO LOCKTONNO LOCK

TONNO LOCK

The Tonno Lock is now a standard feature included with all

Tuff Tonneaus. The Tonno Lock is situated at the front of

the tonneau cover, so as not to impede the accessibility of

the Tuff Tonneau.

Fitting the lock is simple and only requires a small

attachment on the inside edge of the tub behind the cab.

Together with a padlock, it provides you with an extremely

effective theft deterrent. The Tonno Lock is designed to suit

all utes and prevent thieves stealing your Tuff Tonneau, so you can continue to rely on the Tuff

Tonneaus’ name to give you what you want in a tonneau cover.

2.1

2.1 2.1

2.1 BASIC TOOL REQUIRED

BASIC TOOL REQUIREDBASIC TOOL REQUIRED

BASIC TOOL REQUIRED

Rivet gun, Drill, Torch, and Marking Pencil/Pen.

You will need to buy a small Padlock make sure the padlock will go through the hole on the Tonno lock.

2.2

2.2 2.2

2.2 TONNO L

TONNO LTONNO L

TONNO LOCK CONTENTS

OCK CONTENTSOCK CONTENTS

OCK CONTENTS

2 X 4MM Aluminium rivets

1 x Tonno Lock bracket

2.3

2.3 2.3

2.3 FITTING TONNO LOCK

FITTING TONNO LOCKFITTING TONNO LOCK

FITTING TONNO LOCK

1. Attach the black lock bracket to the bracket on the tonneau with your padlock, and fit the tarp.

2. Getting under the tarp with a torch, place the lock bracket against the body and mark holes with a

pen.

3. Remove tonneau and drill the marks with a 4 mm drill bit, place the lock bracket in position and

rivet.

7 | P a g e

3.3.

3. MULTI

MULTIMULTI

MULTI-

-FIT SUPPORT BAR

FIT SUPPORT BARFIT SUPPORT BAR

FIT SUPPORT BAR

The Tuff Tonneau Multi Fit Support Bar is designed to fit

almost all Utes on the Market, from Suburu Brumbys to

Cab Chassis aluminium trays.

Part No: BARADJ

2.1

2.1 2.1

2.1 BASIC TOOL REQUIRED

BASIC TOOL REQUIREDBASIC TOOL REQUIRED

BASIC TOOL REQUIRED

Drill, 4mm drill bit

2.2

2.2 2.2

2.2 MULTI

MULTIMULTI

MULTI-

-FIT SUPPORT BAR

FIT SUPPORT BARFIT SUPPORT BAR

FIT SUPPORT BAR

CONTENTS

CONTENTSCONTENTS

CONTENTS

1 x hollow bar centrepiece 2 x grub screws

2 x solid bar end piece 1 x Tonneau bar sheath

2.3

2.3 2.3

2.3 FITTING

FITTING FITTING

FITTING MULTI

MULTIMULTI

MULTI-

-FIT BAR

FIT BARFIT BAR

FIT BAR

1. Insert solid bar pieces into either end of hollow tube. Adjust bar so it fits between bar bracket

holders with the holes facing to the ground (so the grub screws don’t rub against the tonneau),

as shown above and then with a white pencil make a mark through the small holes of the

hollow bar onto the solid ends. This is where you will drill a hole to the depth of about 1 2mm

(do not go any further)

2. Join the pieces back together and screw grub screws through the hollow bar into the holes that

you drilled.

Make sure you do not over t ghten the grub screws

. Then place the

tonneau sheath over the bar to stop the bar wearing against the tonneau. Refit the bar. You

may kink the bar in the middle to give it some extra height to assist with water runoff.

Warn ng f you do not f t the tonneau sheath over the bar, the tonneau cover w ll qu ckly wear

through wh ch s not covered by warranty.

Your Tuff Tonneau is no ready for ork.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Tuff Tonneaus

Tuff Tonneaus

Tuff Tonneaus 801SB Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 341 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 431SB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 431SB Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 334 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 510 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus Ford PX Ranger Space Cab Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 251 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus Ford PX Ranger Dual Cab Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 11303 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 109 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus Colorado Dual Cab with Headboard 250 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 10812 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 142 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 10018 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 524 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 10634 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 501 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus Bunji Ute Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 144 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 325NSB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 221 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 507 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 142NHB Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario