Tuff Tonneaus 251 Guía de instalación

TONNEAU FITTING INSTRUCTION

Colorado Space Cab with Headboard

2003 –July 2012

Part number: 251

Package includes

1 X Tonneau Cover

2 x Bar Brackets

1 x Tonneau Support Bar

27 x Rivets

1 x Support Bar Sheath

1 x Lock Bracket

1 x Fitting Instructions

20 x Rope Buttons

20 x Anti Abrasive Discs

1. TONNEAU COVER FITTING

NOTE Read entire instructions prior to start.

1.1 BASIC TOOL REQUIRED

Drill, 4mm Drill Bit, Rivet Gun, Marking Pencil / Pen

1.2 TONNEAU COVER INSTALLATION PROCEDURE

1. With a pencil mark the inside edge on each side of the tub at 650mm from the inside front face

of tub towards the rear on each side. Centrally locate the bar bracket over this position and

align the top of the bar bracket 5mm down from the top edge of the tub and drill and rivet

bracket into place. See Figure 1. Repeat for other side of tub. Fit tonneau support bar to bar

brackets.

2. Fit the 3 Plastics at the front of the cover onto the front of the headboard.

3. Ensure tonneau is centred. To fit the rope buttons to the tub, start with the tailgate, vertically

line up each button to each bunji loop starting with the two either side of the tailgate handle.

The height for the buttons on the tailgate is 175mm down from the inside edge of the tailgate.

Work from the centre out, alternating from side to side. Attach each bunji to the button as it is

fitted.

4. To fit the rope buttons to the sides vertically line up each button to each bunji loop starting from

the rear bunji loop, alternating from side to side working towards the front. The height for the

side rope buttons are all measured down 165mm from the TOP INSIDE EDGE of the tub. Attach

each bunji to the button as it is fitted.

NOTE: All measurements are to be taken from the TOP INSIDE EDGE of the tub.

5. To Fit Anti-Abrasive Discs: Firstly clean the area behind each bunji head with a clean

rag and methylated sprits. Then attach the anti-abrasive discs centrally behind each

bunji head.

2. TONNO LOCK

The Tonno Lock is now a standard feature included with all

Tuff Tonneaus. The Tonno Lock is situated at the front of

the tonneau cover, so as not to impede the accessibility of

the Tuff Tonneau.

Fitting the lock is simple and only requires a small

attachment on the inside edge of the tub behind the cab.

Together with a padlock, it provides you with an extremely

effective theft deterrent. The Tonno Lock is designed to suit

all utes and prevent thieves stealing your Tuff Tonneau, so you can continue to rely on the Tuff

Tonneaus’ name to give you what you want in a tonneau cover.

2.1 BASIC TOOL REQUIRED

Rivet gun, Drill, Torch, and Marking Pencil/Pen.

You will need to buy a small Padlock- make sure the padlock will go through the hole on the Tonno lock.

2.2 TONNO LOCK CONTENTS

-2 X 4MM Aluminium rivets

-1 x Tonno Lock bracket

2.3 FITTING TONNO LOCK

1. Attach the black lock bracket to the bracket on the tonneau with your padlock, and fit the tarp.

2. Getting under the tarp with a torch, place the lock bracket against the body and mark holes with a

pen.

3. Remove tonneau and drill the marks with a 4 mm drill bit, place the lock bracket in position and

rivet.

Figure 1: Placement of

bar bracket

650mm

3. MULTI-FIT SUPPORT BAR

The Tuff Tonneau Multi - Fit Support Bar is designed to fit

almost all Utes on the Market, from Suburu Brumbys to Cab

Chassis aluminium trays.

3.1 BASIC TOOL REQUIRED

Drill, 4mm drill bit

3.2 MULTI-FIT SUPPORT BAR CONTENTS

-1 x hollow bar centrepiece - 2 x grub screws

-2 x solid bar end piece - 1 x Tonneau bar sheath

3.3 FITTING MULTI-FIT BAR

1. Insert solid bar pieces into either end of hollow tube. Adjust bar so it fits between bar bracket

holders with the holes facing to the ground (so the grub screws don’t rub against the tonneau),

as shown above and then with a white pencil make a mark through the small holes of the

hollow bar onto the solid ends. This is where you will drill a hole to the depth of about 1-2mm

(do not go any further)

2. Join the pieces back together and screw grub screws through the hollow bar into the holes that

you drilled. Make sure you do not over tighten the grub screws. Then place the

tonneau sheath over the bar to stop the bar wearing against the tonneau. Refit the bar. You

may kink the bar in the middle to give it some extra height to assist with water runoff.

Warning if you do not fit the tonneau sheath over the bar, the tonneau cover will quickly wear

through which is not covered by warranty.

4. WARRANTY AND FEEDBACK

Please register your warranty details online at:

QR Code:

Website Link:

http://www.tto.com.au/en-au/warranty.html

Please complete our 2 minute feedback section as we strive to constantly

improve for our customers.

Your Tuff Tonneau is now ready for work.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Tuff Tonneaus

Tuff Tonneaus

Tuff Tonneaus 411 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 322NSB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 510 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 507 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 10753 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus Ford PX Ranger Space Cab Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 10812 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 10634 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 325NSB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 341 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 431SB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 524 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 142 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 693SB Manual de usuario

Tuff Tonneaus

Tuff Tonneaus Colorado Dual Cab with Headboard 250 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 144 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 660 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 10018 Manual de usuario

Tuff Tonneaus

Tuff Tonneaus Ford PX Ranger Dual Cab Manual de usuario

Tuff Tonneaus

Tuff Tonneaus 431SB Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 325 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 521 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 141 Guía de instalación

Tuff Tonneaus

Tuff Tonneaus 501 Guía de instalación

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario