TSI Instruments IAQ50 Manual de usuario
Indoor Air Quality
Meter
Model IAQ50
OWNER’S MANUAL
ii
LIMITATION OF WARRANTY AND LIABILITY
Seller warrants the goods sold hereunder, under normal use and service as described
in the operator's manual, shall be free from defects in workmanship and material for
twenty-four (24) months, or the length of time specified in the operator's manual, from
the date of shipment to the customer. This warranty period is inclusive of any statutory
warranty. This limited warranty is subject to the following exclusions:
a. Hot-wire or hot-film sensors used with research anemometers, and certain other
components when indicated in specifications, are warranted for 90 days from the
date of shipment.
b. Parts repaired or replaced as a result of repair services are warranted to be free
from defects in workmanship and material, under normal use, for 90 days from
the date of shipment.
c. Seller does not provide any warranty on finished goods manufactured by others or
on any fuses, batteries or other consumable materials. Only the original
manufacturer's warranty applies.
d. Unless specifically authorized in a separate writing by Seller, Seller makes no
warranty with respect to, and shall have no liability in connection with, goods
which are incorporated into other products or equipment, or which are modified by
any person other than Seller.
The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS
stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR
PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE.
TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER
OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL
LOSSES, INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING
CLAIMS BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR
OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE
REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION OF SELLER, THE
REPAIR OR REPLACEMENT OF THE GOODS. IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR
REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be
brought against Seller more than 12 months after a cause of action has accrued. The
goods returned under warranty to Seller's factory shall be at Buyer's risk of loss, and
will be returned, if at all, at Seller's risk of loss.
Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY
AND LIABILITY, which contains the complete and exclusive limited warranty of Seller.
This LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or
its terms waived, except by writing signed by an Officer of Seller.
Service Policy
Knowing that inoperative or defective instruments are as detrimental to TSI as they
are to our customers, our service policy is designed to give prompt attention to any
problems. If any malfunction is discovered, please contact your nearest sales office or
representative, or call Customer Service department at +44 (0) 149 4 459200 (UK),
(800) 874-2811 (USA), or (1) 651-490-2811 (International).
3
Table of Contents
LIMITATION OF WARRANTY AND
LIABILITY................................................................... ii
SECTION 1 General Description.................................5
SECTION 2 Safety...........................................................6
SECTION 3 Setting-Up ..................................................7
Supplying Power to the Model IAQ50 .....................7
Installing the Batteries.................................................7
Using the Optional AC Adapter................................7
Start up Sequence for the Model IAQ50...................8
Battery Percentage...................................................8
Log Percentage.........................................................8
Baud Rate..................................................................8
Setting the Real-Time Clock...................................8
Barometric Pressure ................................................9
Using the Sensing Probe ...........................................10
SECTION 4 Detailed Operation.................................10
Keypad Functions ......................................................10
ON/OFF Key .........................................................11
CO2 Key ...................................................................11
TEMP Key...............................................................12
HUMID Key ...........................................................13
READ/ENTER Key...............................................13
TIME LOG Key ......................................................14
NEXT TEST Key.....................................................16
%OA (Percent Outside Air) Key .........................16
BP Key .....................................................................21
RECALL Key ..........................................................22
Arrow Keys (56).................................................23
DEL Key ..................................................................24
Printing Data Using the Optional MicroPrinter ...25
Connecting the Optional MicroPrinter...................25
4
SECTION 5 Maintenance............................................ 26
Probe Tip..................................................................... 26
Cases ............................................................................ 27
Storage......................................................................... 27
SECTION 6 Service and Calibration ........................ 27
Factory Calibration.................................................... 28
Field Calibration ........................................................ 29
CO2Field Calibration Procedure ............................ 29
Temperature and Humidity Calibrations
Adjustment Procedure.............................................. 32
SECTION 7 Troubleshooting ..................................... 34
SECTION 8 DIP Switch Settings............................... 36
Specifications................................................................. 38
5
SECTION 1
General Description
The Model IAQ50 measures Carbon
Dioxide (CO2) level, temperature and
relative humidity, and calculates dew
point and wet bulb. It also calculates the
percentage of outside (make up) air in a
given indoor space, using CO2levels, or
temperature. The instrument will deter-
mine statistics and recall individual data
points for up to 255 test IDs. The Model
IAQ50 will retain data even after it is
turned off.
The IAQ50 ships in a soft-sided carrying
case that holds the meter and probe, a
probe stand, and calibration collar. There
is space in the case for an optional Micro-
Printer and charger. The instrument ships
with batteries (which are not installed), a
calibration sheet, and this Owner’s
Manual.
6
SECTION 2
Safety
When using the IAQ50 to check for CO2,
temperature or humidity values, make
certain that you can safely raise and hold
the instrument while making measure-
ments. Be especially careful when working
on a ladder.
Observe all necessary precautions so that
the unit does not become caught in
moving machinery or touch any exposed
electrical wiring.
DANGER!
Use with corrosive or other dangerous or
explosive gas mixtures is not recom-
mended.
WARNING!
Do not expose the sensing probe to
excessive heat—it can damage the
sensors and probe.
7
SECTION 3
Setting-Up
Supplying Power to the Model IAQ50
The Model IAQ50 can be powered in one
of two ways: four AA-size batteries or an
optional AC adapter.
Installing the Batteries
Insert four AA batteries as indicated by the
diagram located on the inside of the
battery compartment. The Model IAQ50 is
designed to operate only with alkaline
batteries, which are included. At 15%
battery life remaining, the battery indica-
tor will show that the batteries need to be
changed.
Using the Optional AC Adapter
The optional AC adapter allows you to
power the Model IAQ50 from an AC
outlet. When using the AC adapter, the
batteries (if installed) will be bypassed.
The AC adapter is NOT a battery charger.
8
Start up Sequence for the Model IAQ50
When the instrument is turned on, all
segments of the display will light up and
then the meter goes through a start-up
sequence.
Battery Percentage
This shows the remaining amount of
battery power.
Log Percentage
This shows how much of the datalog-
ging memory is still available.
Baud Rate
The Model IAQ50 has a DEFAULT baud
rate of 1200, which allows it to commu-
nicate with the optional portable Micro-
Printer.
Setting the Real-Time Clock
The Model IAQ50 has an internal clock
that keeps track of the time (the format
is HH.MM where HH is the hour in 24-
hour format and MM is minutes) and
the date. It is very important to set the
time and date correctly, otherwise date
9
and time stamping of recorded data will
not be correct.
To set the time and date, press and hold
either 5or 6key during the power-up
sequence when the time is displayed.
Release the keys when the Model IAQ50
beeps twice. You will have an opportu-
nity to view and/or change the minutes
(min), hours, year, month and date in
sequence. Use the 5or 6key to change
any settings. Use the ENTER key to store
each setting and advance to the next one.
Barometric Pressure
The default barometric pressure is 29.92.
To change this, press the 5or 6keys.
Press ENTER to store the new value. Be
sure to use “stations pressure” which
may be available at the local airport.
“Station pressure” is not corrected to sea
level. The barometric pressure is used to
correct the CO2readings and to calculate
the wet bulb.
The instrument then displays current
conditions. To skip the start-up
10
sequence, press and hold the ENTER
key at any point of the start-up
sequence, until the meter beeps.
Using the Sensing Probe
The sensing probe relies on the diffusion
of air. For best results, try to keep the
sensing probe surrounded by moving air.
Do not breathe on the probe, since humans
exhale levels well exceeding 10,000 ppm
CO2and it may take time for the probe to
re-stabilize.
SECTION 4
Detailed Operation
Keypad Functions
When pressing the keys on the front panel,
the Model IAQ50 will beep to confirm the
function. If you press a key and it does not
beep, the instrument does not allow that
function during the selected mode.
Tabla de contenidos
Otros manuales de Instrumento de medición de TSI Instruments
TSI Instruments
TSI Instruments 9555 Series Manual de operación
TSI Instruments
TSI Instruments Alnor AirGard 405 Manual de usuario
TSI Instruments
TSI Instruments ALNOR LOFLO BALOMETER Series Manual de usuario
TSI Instruments
TSI Instruments DUSTTRAK 8533 Instrucciones de instalación
TSI Instruments
TSI Instruments IAQ-CALC 7545 Manual de operación
TSI Instruments
TSI Instruments dusttrak II 8530 Manual de operación
TSI Instruments
TSI Instruments Flowmaster 250 Guía
TSI Instruments
TSI Instruments dusttrak II 8530 Manual de operación
TSI Instruments
TSI Instruments Sizer 3310A Manual de usuario
TSI Instruments
TSI Instruments Aerotrak 9303 Manual de usuario
TSI Instruments
TSI Instruments 8525 Manual de operación
TSI Instruments
TSI Instruments Q-TRAK XP 7585 Manual de usuario
TSI Instruments
TSI Instruments Alnor Velometer 6000 Series Manual de usuario
TSI Instruments
TSI Instruments VelociCheck 8330 Manual de operación
TSI Instruments
TSI Instruments P-TRAK Ultrafine Manual de operación
TSI Instruments
TSI Instruments 5200 Series Manual de usuario
TSI Instruments
TSI Instruments VelociCalc 9555 Instrucciones de montaje
TSI Instruments
TSI Instruments Alnor Velometer 6000 Series Manual de operación
TSI Instruments
TSI Instruments ALNOR AVM430A Manual de operación
TSI Instruments
TSI Instruments DUSTTRAK 854201-M1 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario