Tripp Lite SMX Series Manual de usuario

Owner’s Manual

SMX

Medical-Grade UPS Systems

with Lithium Iron Phosphate Batteries

Models:

Important Safety Instructions 2

Package Contents 5

Connecting the Batteries 6

Quick Installation 7

Basic Operation 8

Guidance and Manufacturer’s Declaration 11

Storage & Service 12

Battery Warranty Information 13

Regulatory Compliance 13

Español 14

Français 27

Русский 40

Deutsch 53

SMX700HGL

(Series Number: AG-031B)

SMX1200XLHGL

(Series Number: AG-031C)

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-06-259-933821.indb 1 6/20/2018 3:08:23 PM

Important Safety Instructions

Statement of Intended Use

Tripp Lite Medical-Grade UPS Systems are intended to support and protect non-medical computer

equipment and medical devices that require leakage current reduction, surge protection, voltage

regulation, line noise ﬁltering and battery backup during power outages and generator testing, both

inside and outside patient care areas. Tripp Lite’s Medical-Grade UPS Systems come with hospital-

grade plugs and receptacles that reduce leakage to below 100μA.

Product Information

SMX700HGL SMX1200XLHGL

AC Input Voltage 230V 230V

Input Amp(s) 3.6 5

Output Amp(s) 2 3.3

Rated Power (VA/Watts) 700VA, 450W 1000VA, 750W

Frequency 50/60 Hz 50/60 Hz

No. of Phases Single Single

Class Type Class I Class I

Plug/Connector Type Inlet C14 with dongle Inlet C14 with dongle

Operation Continuous Continuous

AC Input Protection (Qty/type/rating) Input breaker (2 x 5A) thermal Input breaker (2 x 6A) thermal

Max Leakage Current (uA) Less than 100uA Less than 100uA

Weight 14.3 kg 15.9 kg

Known Contraindication None None

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may affect

your warranty.

Note: Your UPS incorporates overcurrent protection in both the L1 and L2 input conductors.

UPS Location Warnings

Relevant Symbols

Denotes that information in the manual should be reviewed before use.

Used to signal as a warning that a statement is particularly important and could pose a safety

risk.

Warning-Dangerous Voltage No sitting

Denotes general warning sign No stepping on surface

Refer to Instruction Manual/Booklet No pushing

18-06-259-933821.indb 2 6/20/2018 3:08:23 PM

Important Safety Instructions

• Do not use this equipment within oxygen-enriched atmospheres, or within 0.3 m of a point at

which an oxygen-enriched atmosphere is intentionally vented.

• Use caution when lifting UPS. Because of the considerable weight of all UPS systems, at least

two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the UPS should be used in a location that meets the following conditions:

Temperature: 0 to 40° C; Humidity: 0 to 95% (non-condensing);

Elevation: <2,000 m above sea level; Pressure: >95kPa

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents

or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered

under warranty.

• The UPS is not intended for patient contact. Avoid installations that will cause accidental patient

contact.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a

way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate the

UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

ﬁltered, frequency-regulated output.

• To remove the UPS from the supply mains, the appliance inlet serves as a disconnect device.

• Once connected, do not limit access to the input plug. The plug must be accessible to be used as

a means of disconnection.

• When connecting the UPS to a power outlet, ensure the power outlet is provided with suitable

overcurrent protection in accordance with national and local electrical codes. Ensure the

overcurrent protection has a minimum of 1500A breaking capacity.

CAUTION: Do not remove cover for 5 minutes after disconnecting all sources of

supply. Risk of electric shock—hazardous live parts inside. User must not remove

cover. No user serviceable parts inside. Refer servicing to qualiﬁed service

personnel. This UPS receives power from more DC sources; disconnection of the

AC and DC source is required to de-energize the unit before servicing.

CAUTION: To ensure proper grounding with supply mains power, the input cord must

be connected with an approved country-speciﬁc plug with a protective earth ground

connection.

CAUTION: If this product is operated on battery (not connected to mains power),

adequate safeguards should be employed to protect against accidental contact

with AC power conductors.

CAUTION: Do not exceed total rated output.

WARNING: No modiﬁcation of this equipment is allowed.

18-06-259-933821.indb 3 6/20/2018 3:08:23 PM

Important Safety Instructions

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life-support applications in which a malfunction or failure

of a Tripp Lite UPS System could cause failure or signiﬁcantly alter the performance of a life-

support device.

• The AC output is ﬂoating (the neutral output conductor is not grounded).

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

CAUTION: The unit is for exclusive interconnection with IEC 60601-1 certiﬁed

equipment in the patient environment and IEC 60950-1 certiﬁed equipment outside

of the patient environment. Do not contact SIP/SOP (such as the USB port, RS232

port, etc.) and the patient at the same time.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Only authorized service personnel using the same number and type

of batteries (lithium iron phosphate) should perform battery replacement. The batteries are

recyclable. At the end of the UPS unit’s life, follow best practice by discharging the battery prior to

disposal. Refer to local codes for disposal requirements. Tripp Lite offers a complete line of UPS

System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at

www.tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc UPS replacement

battery.

• Do not operate UPS without batteries.

CAUTION: The unit is intended for use with lithium iron phosphate batteries

provided by Tripp Lite. DO NOT mix with sealed lead acid batteries. This model does

not support external battery packs. DO NOT attempt to add external batteries.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are lithium iron

phosphate batteries. These batteries are highly recyclable. Please refer to local codes for

disposal requirements.

Call Tripp Lite for recycling info at 1.773.869.1234.

For up-to-date information on recycling the batteries in this UPS or any Tripp Lite product,

visit Tripp Lite’s website: http://www.tripplite.com/support/recycling-program/

Replacement Batteries

MODEL BATTERY

AND QUANTITY NOMINAL VOLTAGE

OF BATTERY STRING PART NUMBER

SMX700HGL Lithium Iron Phosphate

12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.

SMX1200XLHGL Lithium Iron Phosphate

12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.

18-06-259-933821.indb 4 6/20/2018 3:08:23 PM

Important Safety Instructions

Package Contents

Maintenance:

• Other than battery replacement, the UPS does not require maintenance. There are no user-

serviceable parts inside. Battery replacement should only be performed by qualiﬁed service

personnel.

Cleaning/Disinfecting:

• Before cleaning or disinfecting, the UPS should be turned off and unplugged.

• For cleaning the UPS, only a damp cloth should be used.

• For disinfecting the UPS, a damp cloth wetted with isopropyl alcohol may be used. No other

cleaning agent should be used.

UPS and Battery Disposal

• Always comply with local ordinances for proper methods of recycling and disposal of electronic

equipment.

• Batteries can present risk of electric shock, burn and ﬁre if not disposed of properly.

SMX700HGL

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

SMX1200XLHGL

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

18-06-259-933821.indb 5 6/20/2018 3:08:23 PM

Connecting the Batteries

1Remove the two screws on

the battery door.

2Remove the battery door.

5 6

The UPS is shipped with the battery disconnected. The battery must be connected for the UPS to

operate. Connect the batteries to the UPS prior to connecting the UPS to AC mains or connecting

any equipment to the UPS.

The installation procedure is as follows:

3Slightly slide the battery

pack out.

4Remove insulation on the

negative (-) battery terminal.

5Connect the negative (-)

battery terminal to the black

battery wire.

6Apply the insulation tape to

negative (-) battery terminal.

7Slide the battery pack back

into the UPS.

8Reinstall the battery door

removed in step 2.

9Reinstall the two screws

removed in step 1.

18-06-259-933821.indb 6 6/20/2018 3:08:26 PM

Quick Installation

1Plug your UPS into a 3-wire grounded,

230V AC 50/60 Hz utility outlet.

After you plug the UPS into a live AC outlet, the UPS will

automatically charge its batteries, but will not supply power

to its outlets until it is turned ON (see Step 3 below). The

BATTERY CHARGE LED will be the only LED illuminated.

2Plug your equipment into the UPS.*

* You will overload the UPS if the total VA ratings for all the

equipment you connect exceeds the UPS’s Output Capacity (see

Speciﬁcations). To ﬁnd your equipment’s VA ratings, look on their

nameplates. If the equipment is listed in amps, multiply the number

of amps by 230 to determine VA. (Example: 1 amp × 230 V = 230

VA). If you are unsure you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

Note: UPS system will function properly upon initial startup; however,

maximum runtime for the unit’s battery will only be accessible after it

has been charged for 24 hours.

3Turn the UPS ON.

Press and hold the “POWER” button for one second. The

alarm will beep once brieﬂy after one second has passed.

Release the button.

NORM DELAY

The following connections are optional; your UPS will function properly without these

connections:

1Serial Communications

(select models only)

You can connect the DB9 serial port on the UPS to the DB9

port of a computer with the included cable. Use with

Tripp Lite’s PowerAlert®software for automatic ﬁle saves

and safe shutdown in case of power failure. (See Basic

Operation Section.)

2USB Communications

Connect the USB port of your UPS to the USB port of a

computer with the included cable. Use with Tripp Lite’s

PowerAlert software for automatic ﬁle saves and safe

shutdown in case of power failure. (See Basic Operation

Section.)

The UPS battery must charge for 24 hours before use.

18-06-259-933821.indb 7 6/20/2018 3:08:28 PM

Basic Operation

Buttons

“POWER” Button:

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet,* press

and hold the POWER button for one second.** Release the button. If utility

power is absent, you can “cold-start” the UPS (i.e., turn it ON and supply

power for a limited time from its batteries***) by pressing and holding the

POWER button for about two seconds.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the POWER button for one second.** Then unplug the UPS from the wall

outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries,

but will not supply power to its outlets until it is turned ON. ** The alarm will beep once

brieﬂy after the indicated interval has passed. *** Fully charged batteries are recommended.

“MUTE/TEST” Button:

To Silence (or “Mute”) UPS Alarms: Brieﬂy press and release the MUTE/TEST

button.*

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds.* The alarm will beep once. Release the

button, and the UPS will perform a self-test. See “Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if it is not turned ON (see “POWER” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will

remove safe electrical grounding and may introduce a damaging

surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the UPS

switches to battery to test its load capacity and battery charge.** If the “OUTPUT

LOAD LEVEL” LED remains lit red and the alarm continues to sound after the test,

the UPS’s outlets are overloaded. To clear the overload, unplug some of your

equipment and run the self-test repeatedly until the “OUTPUT LOAD LEVEL” LED is

no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user

immediately following a self-test may cause the UPS to shut down

and cease supplying output power in the event of a blackout or

severe brownout.

If the “BATTERY WARNING” LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow the

UPS to recharge continuously for 12 hours, and repeat the self-test. If the

LED remains lit, contact Tripp Lite for service. If your UPS requires battery

replacement, visit www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc

Tripp Lite replacement battery for your UPS.

* The alarm will beep once brieﬂy after the indicated interval has passed. ** The “POWER”

LED will be ﬂashing and the “OUTPUT LOAD LEVEL” and “BATTERY CHARGE” LEDs will be lit

and the UPS alarm will sound.

18-06-259-933821.indb 8 6/20/2018 3:08:28 PM

Basic Operation

Indicator Lights

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

“POWER” LED: This green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

ﬂashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, you should save ﬁles and shut

down your equipment since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: This green LED lights continuously whenever the

UPS is automatically correcting high or low AC voltage on the utility line without

the assistance of battery power. The UPS will also emit a slight clicking noise.

These are normal, automatic operations of the UPS. No action is required on your

part.

“OUTPUT LOAD LEVEL” LED: This multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red

(either illuminated continuously or ﬂashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED changes from

red to yellow (or green) and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user

immediately may cause the UPS to shut down and cease

supplying output power in the event of a blackout or severe

brownout.

“BATTERY CHARGE / BATTERY POWER” LED: When the UPS is operating from

utility power, this multicolored LED indicates the approximate charge state of

the UPS’s internal batteries: red indicates the batteries are beginning to charge,

yellow indicates the batteries are roughly midway through charging and green

indicates the batteries are fully charged. When the UPS is operating from battery

power during a blackout or severe brownout, this LED indicates the approximate

amount of energy (ultimately affecting runtime) that the UPS’s batteries will

provide: red indicates a low level of energy, yellow indicates a medium level of

energy and green indicates a high level of energy.

Because runtime performance of all UPS batteries will gradually deplete over

time, it is recommended you periodically perform a self-test (see “MUTE/TEST”

Button description) to determine the energy level of your UPS batteries BEFORE

a blackout or severe brownout occurs. During a prolonged blackout or severe

brownout, you should save ﬁles and shut down your equipment because battery

power will eventually be depleted. When the LED turns red and an alarm sounds

continuously, it indicates the UPS’s batteries are nearly out of power and UPS

shutdown is imminent.

“BATTERY WARNING” LED: This LED lights red and an alarm sounds

intermittently after you initiate a self-test (See “MUTE/TEST” Button description)

to indicate the UPS batteries need to be recharged or replaced. Allow the UPS to

recharge continuously for 12 hours, and repeat the self-test. If the LED continues

to light, contact Tripp Lite for service. If your UPS requires battery replacement,

visit www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc Tripp Lite

replacement battery for your UPS.

18-06-259-933821.indb 9 6/20/2018 3:08:28 PM

Basic Operation

Other UPS Features

AC Receptacles: The receptacles provide your connected equipment with AC

line power during normal operation and battery power during blackouts and

brownouts. They also protect your equipment against damaging surges and line

noise.

USB or DB9 Communication Port: These ports can connect your UPS to any

computer for automatic ﬁle saves and unattended shutdown in the event of a

power failure. Use with Tripp Lite’s PowerAlert Software and appropriate USB or

DB9 cable. You can obtain the software FREE via the Web at www.tripplite.com.

Any user-supplied DB9 pass-through or USB cable may be used to connect your

UPS to your computer.

Note: This connection is optional. The UPS will work properly without this connection.

Battery Replacement Door: Under normal conditions, the original battery in

your UPS will last several years. Battery replacement should be performed only

by qualiﬁed service personnel. Refer to “Battery Warnings” in the Safety section.

Should your UPS require battery replacement, visit www.tripplite.com/products/

battery-ﬁnder to locate the speciﬁc replacement battery for your UPS.

Input Breakers: Protects your electrical circuit from overcurrent draw from the

UPS load. If breaker trips, remove some of the load, then reset it by pressing the

breaker in.

Equipotential Connection: Use this to connect any equipment that requires a

chassis ground.

Power Sensitivity Adjustment: This dial is normally set fully counterclockwise,

which enables the UPS to protect against waveform distortions in its AC input.

When such distortion occurs, the UPS will normally switch to providing PWM

sine wave power from its battery reserves for as long as the distortion is present.

In areas with poor utility power or where the UPS’s input power comes from a

backup generator, chronic waveform distortion could cause the UPS to switch

to battery too frequently, draining its battery reserves. You may be able to

reduce how often your UPS switches to battery due to waveform distortion by

experimenting with different settings for this dial. As the dial is turned clockwise,

the UPS becomes more tolerant of variations in its input power’s AC waveform.

Note: The further the dial is adjusted clockwise, the greater the degree of waveform

distortion the UPS will allow to pass to connected equipment. When experimenting with

different settings for this dial, operate connected equipment in a safe test mode so that the

effect on the equipment of any waveform distortions in the UPS’s output can be evaluated

without disrupting critical operations.

NORM DELAY

18-06-259-933821.indb 10 6/20/2018 3:08:29 PM

Otros manuales para SMX Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartOnline 120/208V Manual de usuario

Tripp Lite

Tripp Lite Internet Office INTERNET350SER Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU10KRT3/1X Manual de usuario

Tripp Lite

Tripp Lite OfficePro 280 Manual de usuario

Tripp Lite

Tripp Lite Internet Office & BC Personal UPS System Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750RTXLCD2U Guía de configuración

Tripp Lite

Tripp Lite HT1500UPS Manual de usuario

Tripp Lite

Tripp Lite SMX1000LCD Manual de usuario

Tripp Lite

Tripp Lite SmartPro VS SMART2200VSXL Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU1500RTXL2UA Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART500USB Manual de usuario

Tripp Lite

Tripp Lite SmartPro VS SMART2200VS Manual de usuario

Tripp Lite

Tripp Lite SmartOnline 200703028 Manual de usuario

Tripp Lite

Tripp Lite AGBC6650 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750RTXLCD2UN Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750XL Manual de usuario

Tripp Lite

Tripp Lite SMART750TSU Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU12000RT4UHW Manual de usuario

Tripp Lite

Tripp Lite SmartOnline 3-Phase UPS System SU30K3/3XR5 Manual de usuario

Tripp Lite

Tripp Lite Digital UPS Systems 200703079 Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMX1200XLHG Manual de usuario

Tripp Lite

Tripp Lite OmniSmart OMNI650LCD Manual de usuario

Tripp Lite

Tripp Lite SmartPro Rackmount Manual de usuario

Tripp Lite

Tripp Lite SU140KMBPK Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario