Tripp Lite SmartOnline Manual de usuario

Owner’s Manual

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

SmartOnline™

Rack/Tower Mount On-Line UPS Systems

Not suitable for mobile applications.

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

For latest updates, please visit www.tripplite.com

Important Safety Instructions 2

Installation 3

Basic Operation 8

Troubleshooting 12

Battery Replacement 13

Storage and Service 14

Warranty Registration 15

Español 16

Français 31

201102199 93-2471.indb 1 3/30/2011 9:13:58 AM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may

affect your warranty.

UPS Location Warnings

• InstallyourUPSindoors,awayfromexcessmoistureorheat,conductivecontaminants,dustor

direct sunlight.

• Forbestperformance,keeptheindoortemperaturebetween32ºFand104ºF

(0ºCand40ºC).

• LeaveadequatespacearoundallsidesoftheUPSforproperventilation.

• Donotmountunitwithitsfrontorrearpanelfacingdown(atanyangle).Mountingin

this manner will seriously inhibit the unit’s internal cooling, eventually causing product

damage not covered under warranty.

UPS Connection Warnings

• ConnectyourUPSdirectlytoaproperlygroundedACpoweroutlet.DonotplugtheUPSinto

itself; this will damage the UPS.

• DonotmodifytheUPS'splug,anddonotuseanadapterthatwouldeliminatetheUPS’sground

connection.

• DonotuseextensioncordstoconnecttheUPStoanACoutlet.Yourwarrantywillbevoidedif

anything other than Tripp Lite surge suppressors are used to connect your UPS to an outlet.

• IftheUPSreceivespowerfromamotor-poweredACgenerator,thegeneratormust

provideclean,filtered,computer-gradeoutput.

Equipment Connection Warnings

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonably

beexpectedtocausethefailureofthelifesupportequipmentortosignificantlyaffectitssafety

oreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofa

flammableanestheticmixturewithair,oxygenornitrousoxide.

• DonotconnectsurgesuppressorsorextensioncordstotheoutputofyourUPS.Thismight

damage the UPS and may affect the surge suppressor and UPS warranties.

Battery Warnings

• Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.Observe

properprecautions.Donotdisposeofthebatteriesinafire.DonotopentheUPSorbatteries.

Donotshortorbridgethebatteryterminalswithanyobject.UnplugandturnofftheUPSbefore

performingbatteryreplacement.Usetoolswithinsulatedhandles.Therearenouser-serviceable

partsinsidetheUPS.Batteryreplacementshouldbeperformedonlybyauthorizedservice

personnelusingthesamenumberandtypeofbatteries(SealedLead-Acid).Thebatteriesare

recyclable.Refertoyourlocalcodesfordisposalrequirementsorvisitwww.tripplite.com/

UPSbatteryrecycling for recycling information. Tripp Lite offers a complete line of UPS System

ReplacementBatteryCartridges(R.B.C.).VisitTrippLiteontheWebatwww.tripplite.com/support/

battery/index.cfmtolocatethespecificreplacementbatteryforyourUPS.

201102199 93-2471.indb 2 3/30/2011 9:13:58 AM

Installation

Rack Mounting

Mountyourequipmentineithera4-postor2-postrackorrackenclosure(seenextpagefor2-post

mounting).Theusermustdeterminethefitnessofhardwareandproceduresbeforemounting.If

hardware and procedures are not suitable for your application, contact the manufacturer of your

rack or rack enclosure. The procedures described in this manual are for common rack and rack

enclosure types and may not be appropriate for all applications.

4-Post Mounting

AllUPSmodelsincludehardwarerequiredtomountina4-postrack.Selectmodelsincludean

adjustablerackmountshelfkittoprovideadditionalsupport. If your UPS model does not include

an adjustable rackmount shelf kit, skip steps 1 and 2.

1Connect the two segments of each shelf A

using the included screws and nuts B.

Leave the screws slightly loose so that the

shelvescanbeadjustedinthenextstep.

2Adjusteachshelftofityourrack,then

mount them in the lowest available space

of your rack with the screws, nuts and

washers provided C. Note that the support

ledges should face inward. Tighten the

screws that connect the shelf segments B.

3Attach mounting ears Dto the front

mountingholesofyourequipment Eusing

the screws provided F. The ears should

face forward.

4Using an assistant if necessary, lift your

equipmentandslideitontothemounting

shelves.Attachyourequipmenttotherack

by using the appropriate hardware G

through its mounting ears and into the rack

rails.

201102199 93-2471.indb 3 3/30/2011 9:13:59 AM

Yourmodelmaydiffer.

2-Post (Telecom) Mounting

Ifyoumount2UUPSmodelsin2-postracks,theyrequiretheadditionofaTrippLite2-Post

RackmountInstallationKit(model:2POSTKITRMWM,soldseparately).SeeInstallationKitowner’s

manual for installation procedure for 2U UPS models.

Installation

Mounting (Tower)

YourUPScanbemountedinanuprighttower

position with optional base stands sold

separatelybyTrippLite(Model#2-9USTAND).

WhenmountingtheUPSonadjustablebase

stands, make sure that the control panel is

toward the top. The control panel may be

rotatedtomakeiteasiertoread.Insertasmall

screwdriver or similar tool in the slots on either

side of the panel, pop it out, rotate it, and pop

it back into place as shown.

WARNING!

All UPS systems are extremely heavy. Use

caution when lifting and mounting. User

must properly stabilize the UPS when lifting

and mounting.

Connection and Start-Up

1Plug your UPS’s line cord into an

electrical outlet.

 YourUPSmustbeconnectedtoa

dedicated circuit of sufficient amperage.

Note, however, that the select models may

be fitted with different plug types. Refer to

the “OP Rating/Plug Rating” chart printed

on the top of your UPS.

Once your UPS is plugged in, the fan and

allIndicatorLightswillturnON.The“LINE”

and“LOADACTIVEMETER”LEDswill

illuminate and the UPS will emit a beep to

indicate normal operation. However, power

isnotsuppliedtoyourUPS’sACoutlets

until the UPS is turned on.

2Plug your equipment into your UPS.

 YourUPSisdesignedtosupportcomputer

equipmentonly.YouwilloverloadyourUPS

if you connect household appliances or

laserprinterstotheUPS'soutlets.

201102199 93-2471.indb 4 3/30/2011 9:14:00 AM

1Yourmodelmaydiffer.

Yourmodelmaydiffer.

Installation

3Turn your UPS ON:

• Pressthe“ON/TEST”Button

• Holditforseveralsecondsuntilyouhear

a beep

• Releaseit

 YourUPSwillbeginprovidingACpowerto

itsoutlets.The“ONLINE”LEDwill

illuminate.

Note: UPS system will function properly upon

initial startup; however, maximum runtime for the

unit’s battery will only be accessible after it has

been charged for 24 hours.

Optional Connections

YourUPSwillfunctionproperlywithouttheseconnections.

1Phone Line or Phone/Network

Line Surge Suppression

 YourUPShasjackswhichprotectagainst

surges on a phone line. Select models

featurejackswhichalsoprotectagainst

surges on a network line.* Using

appropriate telephone or network cords

connectyourwalljacktotheUPSjack

marked“IN.”Connectyourequipmentto

theUPSjackmarked“OUT.”Makesurethe

equipmentyouconnecttotheUPS'sjacks

is also protected against surges on the AC

line.

 *NotcompatiblewithPoE(PowerOverEthernet)

applications.

2USB and RS-232 Serial

Communications

 UsetheincludedUSBcable(see 2a )and/

orDB9serialcable(see 2b )toconnect

the communication port of your computer

to the communication port of your UPS.

InstallonyourcomputertheTrippLite

PowerAlert Software appropriate to your

computer'soperatingsystem.YourUPSmay

feature additional communications ports;

these ports may be connected to additional

computers that have PowerAlert Software

installed. Consult your PowerAlert manual

for more information.

201102199 93-2471.indb 5 3/30/2011 9:14:01 AM

4-5

Yourmodelmaydiffer.

Installation

3EPO Port Connection

This optional feature is only for those

applicationsthatrequireconnectiontoa

facility’sEmergencyPowerOff(EPO)circuit.

WhentheUPSisconnectedtothiscircuit,it

enablesemergencyshutdownoftheUPS’s

inverter and inhibits transfer to internal bypass.

Using the cable provided, connect the EPO port

of your UPS (see 3a )toauser-supplied

normally closed or normally open switch

according to the circuit diagram (see 3b ).

Note:

1. If using a cable other than what is supplied, the

cable should not exceed 350 feet or have a

resistance of greater than 10 ohms.

2. If a non-latching EPO switch is used, the EPO must

be held for a minimum of 1 second. This does not

apply to a latching EPO switch.

CAUTION: The EPO port is not a phone line

surge suppressor; do not connect a phone

line to this port.

UPSUnitStatewhenassertingEPOwithAClinepresent:

LEDs Output Fans Serial SNMP USB

OFF OFF ON ON ON ON

TorestarttheUPSunitafterassertingEPOwithAClinepresent:

Option 1:

1.VerifythattheEPOassertionhasbeenremovedorcleared.

2.PressOFFbuttonuntilyouhearaclick(approx.1second).

3.PressONbuttonandUPSoutputwillturnbackon.

Option 2:

1.VerifythattheEPOassertionhasbeenremovedorcleared.

2. Remove AC line power to the UPS unit.

3.ReapplyAClinepower.NowtheUPSwillstartbackupinnormaloperationmode.

UPSUnitStatewhenassertingEPOwithoutAClinepower:

LEDs Output Fans Serial SNMP USB

OFF OFF OFF OFF OFF OFF

TorestarttheUPSunitafterassertingEPOwithoutAClinepower:

1.VerifythattheEPOassertionhasbeenremovedorcleared.

2. Reapply AC line power to the UPS unit. Now the UPS will start back up in normal operation

mode.

201102199 93-2471.indb 6 3/30/2011 9:14:01 AM

48V/26A

Yourmodelmaydiffer.

Installation

4External Battery Connection

(select models)

 Checktoensurethattheexternalbatteries

you are connecting match the voltage listed

onyourUPS'sbatteryconnector.AllUPS

models come with a robust internal battery

system; select models feature connectors

thatacceptoptionalexternalbatterypacks

(soldseparatelyfromTrippLite)toprovide

additionalruntime.Addingexternalbatteries

will increase recharge time as well as

runtime.Seethebatterypackowner's

manual for complete installation

instructions. Make sure cables are fully

inserted into their connectors. Small sparks

may result during battery connection; this is

normal.Donotconnectordisconnect

battery packs when the UPS is running on

battery power.

201102199 93-2471.indb 7 3/30/2011 9:14:02 AM

Basic Operation

Front Panel Switches

“ON/TEST” Button: ThisswitchcontrolsfourseparateUPSfunctions:

UPS Power ON

To turn the UPS on, press this button, hold it for several seconds until you

hearabeep,thenreleaseit.The“ONLINE”LEDwillilluminate.

UPS Self-Test

Duringnormalon-lineoperation,pressthisbuttonandholdituntilyou

hearabeep.Thisinitiatesa10-secondself-testofthebattery.TheUPS

willshifttobatterypower(allLEDswillilluminate)fortenseconds.

Alarm Silence

TosilencetheUPS“on-battery”alarm,pressthisbuttonandholdituntil

you hear a beep.

UPS Cold Start

TouseyourUPSasastand-alonepowersourcewhenACpoweris

unavailable(i.e.duringablackout),pressthisbuttonandholdituntilyou

hear a beep. The UPS will then provide battery power to its outlets.*

* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating

from battery power.

“OFF” Button: This button turns power OFF at the UPS receptacles. Press

this switch, hold it until you hear a beep, then release it. The UPS will

continue charging and the fan will continue to cool internal components

even after you turn the UPS receptacles off. To turn the UPS OFF

completely,includingthecharger,disconnecttheUPS’spowercordafter

pressing the “OFF” switch.

Front Panel Indicator Lights

“ONLINE”LED:This green light will illuminate constantly to indicate the

UPSisperformingnormalon-lineoperation(filteringandresynthesizing

incomingAClinevoltagetoprovidepuresinewaveoutput).Whenthislight

isilluminated,youcanmonitortheloadlevelofyourUPSonthe“LOAD

ACTIVEMETER”LEDs.

“LINE”LED:This green light will illuminate constantly to indicate the utility

suppliedAClinevoltageatyourwalloutletisnominal.Itwillflashifthe

linevoltageisoutsidethenominalrange(eithertoolowortwohigh).No

actionisrequiredonyourpartwhentheLEDflashes;theUPScontinuously

andautomaticallyfiltersAClinepowertoprovideyourequipmentwithpure

sinewaveACpower,regardlessofbrownoutorovervoltageconditions.If

thislightisoff,thenAClinevoltageisnotpresent(blackout)orisatan

extremelyhighvoltage,andtheUPSwillprovideconnectedequipmentwith

power from battery.

201102199 93-2471.indb 8 3/30/2011 9:14:02 AM

Basic Operation

“BYPASS”LED:ThisyellowlightwillflashtoindicatethattheUPS’sDC/AC

inverterisdeactivatedandtheUPSisinthe“Bypass”mode.Duringnormal

operationthisLEDwilllightbrieflywhentheunitispluggedin,butifan

internal fault or overload occurs this light will flash constantly and the fault

LEDwillilluminatetoshowthatconnectedequipmentwillreceivefiltered

ACmainspower,butwillnotreceivebatterypowerduringablackout.In

thiscase,contactTrippLiteforservice.IftheUPShasbeenplacedinto

EconomyMode(availableonselectUPSsystems),itconfiguresanonline

UPStofunctionasaswitchingUPS.WhentheUPSsystemisinEconomy

Mode, it operates at increased efficiency while AC utility power is available

(within+/-10%nominal)andswitchestobatterypowerifACutilitypower

isinterrupted.Theyellow“BYPASS”LEDwillremainonwhentheUPS

system is in Economy Mode. (For more information on how to access the

EconomyMode,pleaserefertothePowerAlertsoftwareUser’sManual)

“FAULT”LED(selectmodelsonly):This red light will flash when your UPS

detectsaninternalfault(overheating,overvoltages,etc.)orwhenitdetects

awiringfaultinyourwalloutlet(reversedphases,missingground,etc.)

The UPS will only detect wiring faults when it is plugged into a utility outlet

butnotturnedON.IfthelightpersistsafterrestartingtheUPS,contactan

electriciantochecktheACline.YourUPSwillidentifythepresenceofmost

(butnotall)wiringfaults.

“LOADACTIVEMETER”LED:This green light will illuminate when your

UPSisreceivingACpowertoindicatethatthesetoffourdual-function

LEDsisdisplayingtheloadlevelofyourUPS.

“BATTACTIVEMETER”LED:This green light will illuminate when your UPS

isoperatingfrombatterypowertoindicatethatthesetoffourdual-

functionLEDsisdisplayingthebatterychargelevelofyourUPS.Note:the

“ONBATT”LEDwillalsobeilluminated.

“OVERLOAD”LED:This red light will illuminate constantly to indicate that

yourUPS’scapacityhasbeenexceededwhileitisinon-lineoperation.The

UPSalarmwillbeepcontinuously.Immediatelyremoveoverloaduntillight

andalarmgoesoff.Ifyoudonotimmediatelyremovetheoverload,the

UPSwilltransferfromon-linetobypassoperation.

“BATTLOW”LED:ThisyellowlightwillilluminatewhenyourUPS’sbattery

charge level is low. The UPS alarm will beep until either the battery charge

isdepletedorthebatteriesareadequatelyrecharged.

“ONBATT”LED:This green light will illuminate constantly to indicate that

AClinevoltageisnotpresentandyourUPSisprovidingyourequipment

with battery power. The UPS will also beep every two seconds, unless

silencedbythe“ON/TEST”Button.Whenthislightisilluminated,youcan

monitorthebatterychargelevelofyourUPSonthe“BATTACTIVEMETER”

LEDs.

201102199 93-2471.indb 9 3/30/2011 9:14:03 AM

Basic Operation

“REPLACEBATT”LED:This red light will illuminate constantly and the UPS

alarmwillbeepevery2secondsifyourUPS’smicroprocessordetectsa

batteryfaultorifyourUPSfailstheautomaticself-test(afteryouturnyour

UPSON)andtheUPSbatteryislessthanfullycharged.LettheUPS

system charge for at least 12 hours and perform a self test using the “ON/

TESTButton”asdescribedonpage7.Ifthelightcontinuestostayon,

contact Tripp Lite for service.

Rear Panel

Accessory Slot: Remove the small cover panel from this slot to use

optional accessories to remotely monitor and control your UPS. Contact

TrippLiteCustomerSupportat(773)869-1234formoreinformation,

including a list of available SNMP, network management and connectivity

products.

ExternalBatteryPackConnector(configurationvariesbymodel):Use

toconnectoptionalTrippLiteBatteryPacksforadditionalruntime.Contact

TrippLiteCustomerSupportat(773)869-1234fortheappropriateTripp

Litebatterypacktoconnect.RefertoinstructionsavailablewiththeBattery

Pack for complete connection information and safety warnings.

Fan: ThefancoolstheUPS’sinternalcomponents.Itisalwaysonwhen

line power is present.

Input Circuit Breaker Switch: This resettable breaker prevents high input

currentfromdamagingtheUPSortheattachedload.Ifthisbreakertrips,

make sure your UPS is connected to AC power of the proper voltage before

resetting the circuit breaker by pushing the breaker switch in.

Ground Screw: Usethistoconnectanyequipmentthatrequiresachassis

ground.

OutputCircuitBreakersSwitches(SelectModelsOnly):These

resettablecircuitbreakersprotectyourUPSfromoutputoverload.Ifoneor

bothbreakerstrip,removesomeoftheloadonthecircuit(s)andallowthe

UPStocoolbeforepressingthebreakerswitch(es)intoreset.

Input Cord: This permanently attached power cord connects your UPS to a

power outlet.

201102199 93-2471.indb 10 3/30/2011 9:14:04 AM

Otros manuales para SmartOnline

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite Omni VS Manual de usuario

Tripp Lite

Tripp Lite SUPDM11 Manual de usuario

Tripp Lite

Tripp Lite AVR750U Manual de usuario

Tripp Lite

Tripp Lite SmartPro UPS System SMART550USB Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU8000RT3UN50TF Manual de usuario

Tripp Lite

Tripp Lite 1500SLT Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU3000RTXL3U Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART500USB Manual de usuario

Tripp Lite

Tripp Lite Power Suppy Manual de usuario

Tripp Lite

Tripp Lite AVRX550UA Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU10KRT3U Manual de usuario

Tripp Lite

Tripp Lite SmartOnline Intelligent True On-Line UPS... Instrucciones de instalación y funcionamiento

Tripp Lite

Tripp Lite SmartPro SMART1500RM2U Manual de usuario

Tripp Lite

Tripp Lite TE Series Manual de usuario

Tripp Lite

Tripp Lite SmartPro Rackmount SMX500RT1U Manual de usuario

Tripp Lite

Tripp Lite Smart Pro 450 RT Manual de usuario

Tripp Lite

Tripp Lite BC600SINE Manual de usuario

Tripp Lite

Tripp Lite SmartPro SLT Manual de usuario

Tripp Lite

Tripp Lite AVR700U Guía de configuración

Tripp Lite

Tripp Lite SmartOnline SU1000RTXL2U Guía de configuración

Tripp Lite

Tripp Lite AVRT450U Manual de usuario

Tripp Lite

Tripp Lite ECO750UPSTAA Manual del propietario

Tripp Lite

Tripp Lite SmartOnline AGPS5548 Manual de usuario

Tripp Lite

Tripp Lite AVRX Series Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario