Tripp Lite SmartOnline 2-9USTAND Manual de usuario

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Installation 3

Basic Operation 7

Battery Replacement 13

Storage and Service 14

SmartOnline™

Rack/Tower Mount On-Line UPS Systems

Warranty Registration 14

Español

Français 29

Troubleshooting 11

Warranty Registration:

win a FREE Tripp Lite product—

www.tripplite.com/warranty

Not suitable for mobile applications.

UPS Location Warnings

• InstallyourUPSindoors,awayfromexcessmoistureorheat,conductivecontaminants,

dustordirectsunlight.

• Forbestperformance,keeptheindoortemperaturebetween32ºFand104ºF(0ºCand

40ºC).

• LeaveadequatespacearoundallsidesoftheUPSforproperventilation.

• Do not mount unit with its front or rear panel facing down (at any angle).

Mounting in this manner will seriously inhibit the unit’s internal cooling, eventually

causing product damage not covered under warranty.

UPS Connection Warnings

• ConnectyourUPSdirectlytoaproperlygroundedACpoweroutlet.Donotplugthe

UPSintoitself;thiswilldamagetheUPS.

• DonotmodifytheUPS'splug,anddonotuseanadapterthatwouldeliminatetheUPS’s

groundconnection.

• DonotuseextensioncordstoconnecttheUPStoanACoutlet.Yourwarrantywillbe

voidedifanythingotherthanTrippLitesurgesuppressorsareusedtoconnectyourUPS

to an outlet.

• IftheUPSreceivespowerfromamotor-poweredACgenerator,thegeneratormust

provideclean,filtered,computer-gradeoutput.

Equipment Connection Warnings

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcan

reasonablybeexpectedtocausethefailureofthelifesupportequipmentorto

significantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethis

equipmentinthepresenceofaflammableanestheticmixturewithair,oxygenornitrous

oxide.

• DonotconnectsurgesuppressorsorextensioncordstotheoutputofyourUPS.This

mightdamagetheUPSandwillvoidthesurgesuppressorandUPSwarranties.

Battery Warnings

Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.

Observeproperprecautions.Donotdisposeofthebatteriesinafire.DonotopentheUPS

orbatteries.Donotshortorbridgethebatteryterminalswithanyobject.Unplugandturn

offtheUPSbeforeperformingbatteryreplacement.Usetoolswithinsulatedhandles.

Therearenouser-serviceablepartsinsidetheUPS.Batteryreplacementshouldbe

performedonlybyauthorizedservicepersonnelusingthesamenumberandtypeof

batteries(sealedLead-Acid).Thebatteriesarerecyclable.Refertoyourlocalcodesfor

disposalrequirementsorintheUSAonlycall1-800-SAV-LEADor1-800-8-BATTERY

(1-800-822-8837)orvisitwww.rbrc.comforrecyclinginformation.TrippLiteoffersa

completelineofUPSSystemReplacementBatteryCartridges(R.B.C.).VisitTrippLiteon

theWebatwww.tripplite.com/support/battery/index.cfmtolocatethespecificreplacement

batteryforyourUPS.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation,operationandstorageofallTrippLiteUPSSystems.Failuretoheedthese

warningswillvoidyourwarranty.

Important Safety Instructions

Mountyourequipmentineithera4-postor2-postrackorrackenclosure(seenextpagefor

2-post mounting). The user must determine the fitness of hardware and procedures before

mounting. If hardware and procedures are not suitable for your application, contact the

manufacturerofyourrackorrackenclosure.Theproceduresdescribedinthismanualarefor

commonrackandrackenclosuretypesandmaynotbeappropriateforallapplications.

4-Post Mounting

AllUPSmodelsincludehardwarerequiredtomountina4-postrack.Selectmodelsincludean

adjustablerackmount shelfkit toprovideadditional support.If your UPS model does not

include an adjustable rackmount shelf kit, skip steps 1 and 2.

Connect the two segments of each shelf A

usingtheincludedscrewsandnuts B.Leave

the screws slightly loose so that the shelves

canbeadjustedinthenextstep.

Adjusteachshelftofityourrack,thenmount

theminthelowestavailablespaceofyourrack

with the screws, nuts and washers provided

C.Notethat thesupportledges shouldface

inward. Tighten the screws that connect the

shelfsegments B.

Attachmountingears Dtothefrontmounting

holesofyourequipment Eusingthescrews

provided F.Theearsshouldfaceforward.

Using an assistant if necessary, lift your

equipment and slide it onto the mounting

shelves.Attachyourequipmenttotherackby

usingtheappropriatehardware Gthroughits

mountingearsandintotherackrails.

Mounting Rack

Installation

Installation (continued)

2-Post (Telecom) Mounting

Ifyoumount2UUPSmodelsin2-postracks,theyrequiretheadditionofaTrippLite2-Post

RackmountInstallationKit(model:2POSTKITRMWM,soldseparately).SeeInstallationKit

owner’smanualforinstallationprocedurefor2UUPSmodels.

Mounting (Tower)

Your UPS can be mounted in an upright tower

positionwithoptionalbasestandssoldseparately

by Tripp Lite (Model # 2-9USTAND). When

mounting the UPS on adjustable base stands,

makesurethatthecontrolpanelistowardthetop.

The control panel may be rotated to make it

easier to read. Insert a small screwdriver or

similartoolintheslotsoneithersideofthepanel,

popitout,rotateit,andpopitbackintoplaceas

shown.

WARNING!

All UPS systems are extremely heavy. Use

caution when lifting and mounting. User must

properly stabilize the UPS when lifting and

mounting.

Important Safety Instructions

Connection and Start-Up

Plug your UPS’s line cord into an

electrical outlet.

Your UPS must be connected to a dedicated

circuitof sufficientamperage.Note, however,

that the select models may be fitted with

differentplugtypes.Refertothe“OPRating/

PlugRating”chartprintedonthetopofyour

UPS.

OnceyourUPSispluggedin,thefanandall

IndicatorLightswillturnON.The“LINE”and

“LOADACTIVEMETER”LEDswillilluminate

andtheUPSwillemitabeeptoindicatenormal

operation.However,poweris notsupplied to

your UPS’sAC outlets until the UPS is turned

on.

Plug your equipment into your UPS.

Your UPS is designed to support computer

equipmentonly.YouwilloverloadyourUPSif

you connect household appliances or laser

printerstotheUPS'soutlets.

Turn your UPS ON:

• Pressthe“ON/TEST”Button

• Holditforseveralsecondsuntilyou

 hearabeep

• Releaseit

Your UPS will begin providing AC power to its outlets.

The “ON LINE” LED will illuminate.

Your UPS will function properly without these

connections.

Phone Line or Phone/Network

Line Surge Suppression

Your UPS has jacks which protect against

surgesonaphoneline.Selectmodelsfeature

jacks which also protect against surges on a

networkline.*Usingappropriatetelephoneor

network cords connect your wall jack to the

UPS jack marked “IN.” Connect your

equipment to the UPS jack marked “OUT.”

Makesure the equipmentyouconnect tothe

UPS'sjacksisalsoprotectedagainstsurgeson

theACline.

*NotcompatiblewithPoE(PowerOverEthernet)applications.

Your model may differ.

Installation (continued)

Optional Connections

1Your model may differ.

Optional Connections (continued)

USB and RS-232 Serial

Communications (all models)

UsetheincludedUSBcable(see 2a )and/or

DB9 serial cable (see 2b ) to connect the

communication port of your computer to the

communication port of your UPS. Install on

your computer the Tripp Lite PowerAlert

Software appropriate to your computer's

operating system. Your UPS may feature

additional communications ports; these ports

maybeconnectedtoadditionalcomputersthat

have PowerAlert Software installed. Consult

your PowerAlert manual for more

information.

EPO Port Connection (all models)

This optional feature is only for those

applications that require connection to a

facility'sEmergencyPowerOff(EPO)circuit.

WhentheUPSis connectedtothis circuit,it

enables emergency shutdown of the UPS's

inverter.Usingthecableprovided,connectthe

EPO port of your UPS (see 3a ) to a user-

supplied normally closed or normally open

switch according to the circuit diagram (see

3b ).The EPO port is not a phone line surge

suppressor; do not connect a phone line to

this port.

External Battery Connection

(select models)

Checktoensurethattheexternalbatteriesyou

areconnectingmatchthevoltagelistedonyour

UPS's battery connector. All UPS models

come with a robust internal battery system;

select models feature connectors that accept

optionalexternalbatterypacks(soldseparately

fromTrippLite)toprovideadditionalruntime.

Addingexternalbatterieswillincreaserecharge

timeaswellasruntime.Seethebatterypack

owner's manual for complete installation

instructions.Makesurecablesarefullyinserted

intotheirconnectors.Smallsparksmayresult

duringbatteryconnection;thisisnormal.Do

notconnectordisconnectbatterypackswhen

theUPSisrunningonbatterypower.

48V/26A

Your model may differ.

Installation (continued)

2a Your model may differ.

3a Your model may differ.

4-5

Front Panel Switches

“ON/TEST” Button: This switch controls four separate UPS

functions:

UPS Power ON

ToturntheUPSon,pressthisbutton,holditforseveralsecondsuntil

you hear a beep, then release it. The “ON LINE” LED will

illuminate.

UPS Self-Test

Duringnormalon-lineoperation,pressthisbuttonandholdituntil

youhearabeep.Thisinitiatesa10-secondself-testofthebattery.The

UPS will shift to battery power (all LEDs will illuminate) for ten

seconds.

Alarm Silence

TosilencetheUPS“on-battery”alarm,pressthisbuttonandholdit

untilyouhearabeep.

UPS Cold Start

TouseyourUPSasastand-alonepowersourcewhenACpoweris

unavailable(i.e.duringablackout),pressthisbuttonandholdituntil

you hear a beep. The UPS will then provide battery power to its

outlets.*

* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating

from battery power.

“OFF” Button:ThisbuttonturnspowerOFFattheUPSreceptacles.

Pressthisswitch,holdituntilyouhearabeep,thenreleaseit.The

UPSwillcontinuechargingandthefanwillcontinuetocoolinternal

componentsevenafteryouturntheUPSreceptaclesoff.Toturnthe

UPS OFF completely, including the charger, disconnect the UPS’s

powercordafterpressingthe“OFF”switch.

“ON LINE” LED:Thisgreenlightwillilluminateconstantlytoindicate

the UPS is performing normal on-line operation (filtering and

resynthesizingincomingAClinevoltagetoprovidepuresinewave

output).Whenthislightisilluminated,youcanmonitortheloadlevel

ofyourUPSonthe“LOADACTIVEMETER”LEDs.

“LINE” LED:Thisgreenlightwillilluminateconstantlytoindicate

theutilitysuppliedAClinevoltageatyourwalloutletisnominal.It

willflashifthelinevoltageisoutsidethenominalrange(eithertoo

lowortwohigh).NoactionisrequiredonyourpartwhentheLED

flashes; the UPS continuously and automatically filters AC line

power to provide your equipment with pure sine waveACpower,

regardlessofbrownoutorovervoltageconditions.Ifthislightisoff,

thenAClinevoltageisnotpresent(blackout)orisatanextremely

high voltage, and the UPS will provide connected equipment with

powerfrombattery.

Front Panel Indicator Lights

Basic Operation

Front Panel Indicator Lights continued

“BYPASS” LED: This yellow light will flash to indicate that the

UPS’sDC/ACinverterisdeactivatedandtheUPSisinthe“Bypass”

mode.DuringnormaloperationthisLEDwilllightbrieflywhenthe

unitispluggedin,butifaninternalfaultoroverloadoccursthislight

willflashconstantlyandthefaultLEDwillilluminatetoshowthat

connectedequipmentwillreceivefilteredACmainspower,butwill

notreceivebatterypowerduringablackout.Inthiscase,contactTripp

Lite for service. If the UPS has been placed into Economy Mode

(available on select UPS systems), it configures an online UPS to

functionasaswitchingUPS.WhentheUPSsystemisinEconomy

Mode,itoperates atincreasedefficiency whileACutility poweris

available(within+/-10%nominal)andswitchestobatterypowerif

AC utility power is interrupted. The yellow “BYPASS” LED will

remain on when the UPS system is in Economy Mode. (For more

informationonhowtoaccesstheEconomyMode,pleaserefertothe

PowerAlertsoftwareUser’sManual)

“FAULT” LED (select models only):Thisredlightwillflashwhen

yourUPSdetectsaninternalfault(overheating,overvoltages,etc.)or

when it detects a wiring fault in your wall outlet (reversed phases,

missingground,etc.)TheUPSwillonlydetectwiringfaultswhenitis

pluggedintoautilityoutletbutnotturnedON.Ifthelightpersistsafter

restartingtheUPS,contactan electricianto checktheACline.Your

UPSwillidentifythepresenceofmost(butnotall)wiringfaults.

“LOAD ACTIVE METER” LED:Thisgreenlightwillilluminate

whenyourUPSisreceivingACpowertoindicatethatthesetoffour

dual-functionLEDsisdisplayingtheloadlevelofyourUPS.

“BATT ACTIVE METER” LED:Thisgreenlightwillilluminate

whenyourUPSisoperatingfrombatterypowertoindicatethatthe

setoffourdual-functionLEDsisdisplayingthebatterychargelevel

ofyourUPS.Note:the“ONBATT”LEDwillalsobeilluminated.

“OVERLOAD” LED:Thisredlightwillilluminateconstantlytoindicate

thatyourUPS’scapacityhasbeenexceededwhileitisinon-lineoperation.

TheUPSalarmwillbeepcontinuously.Immediatelyremoveoverload

untillightandalarmgoesoff.Ifyoudonot immediatelyremovethe

overload,theUPSwilltransferfromon-linetobypassoperation.

“BATT LOW” LED:ThisyellowlightwillilluminatewhenyourUPS’s

batterychargelevelislow.TheUPSalarmwillbeepuntileitherthe

batterychargeisdepletedorthebatteriesareadequatelyrecharged.

“ON BATT” LED: This green light will illuminate constantly to

indicatethatAClinevoltageisnotpresentandyourUPSisproviding

yourequipmentwithbatterypower.TheUPSwillalsobeepeverytwo

seconds,unlesssilencedbythe“ON/TEST”Button.Whenthislight

isilluminated,youcanmonitorthebatterychargelevelofyourUPS

onthe“BATTACTIVEMETER”LEDs.

Basic Operation (continued)

Rear Panel

“REPLACE BATT” LED: This red light will illuminate constantly

and the UPS alarm will beep every 2 seconds if your UPS’s

microprocessor detects a battery fault or if your UPS fails the

automaticself-test(afteryouturnyourUPSON)andtheUPSbattery

islessthanfullycharged.LettheUPSsystemchargeforatleast12

hoursandperformaselftestusingthe“ON/TESTButton”asdescribed

onpage7. If thelightcontinues tostayon, contactTrippLite for

service.

Accessory Slot:Removethesmallcoverpanelfromthisslottouse

optional accessories to remotely monitor and control your UPS.

Contact Tripp Lite Customer Support at (773) 869-1234 for more

information,includingalistofavailableSNMP,networkmanagement

andconnectivityproducts.

External Battery Pack Connector (configuration varies by model):

Use to connect optional Tripp Lite Battery Packs for additional

runtime.ContactTrippLiteCustomerSupportat(773)869-1234for

theappropriateTrippLitebatterypacktoconnect.Refertoinstructions

availablewiththeBatteryPackforcompleteconnectioninformation

andsafetywarnings.

Fan:ThefancoolstheUPS’sinternalcomponents.Itisalwayson

whenlinepowerispresent.

Input Circuit Breaker Switch:Thisresettablebreakerpreventshigh

input current from damaging the UPS or the attached load. If this

breakertrips,makesureyourUPSisconnectedtoACpowerofthe

proper voltage before resetting the circuit breaker by pushing the

breakerswitchin.

Ground Screw: Use this to connect any equipment that requires a

chassisground.

Output Circuit Breakers Switches (Select Models Only):These

resettablecircuitbreakersprotectyourUPSfromoutputoverload.If

oneorbothbreakerstrip,removesomeoftheloadonthecircuit(s)

andallowtheUPStocoolbeforepressingthebreakerswitch(es)in

to reset.

Front Panel Indicator Lights continued

Basic Operation (continued)

Rear Panel continued

Input Cord: This permanently attached power cord connects your

UPStoapoweroutlet.

AC Receptacles (Varied by Model): These 15-, 20- and 30-amp

receptaclesprovide yourconnected equipmentwith puresine-wave

ACoutputfromtheAClineduringnormaloperationandfrombattery

power during blackouts and severe brownouts. Power provided at

these outlets is filtered to protect connected equipment against

damaging surges and line noise. The receptacles are divided into

numbered load banks, as labelled on the unit. Using PowerAlert

softwareand cabling,loadbanks oneandtwomaybe individually

turnedoffandonfromaremotelocation,allowinguserstoresetor

rebootconnectedequipment.

Telephone or Telephone/Network Protection Jacks: These jacks

protect your equipment against surges over a telephone line or

telephone/networkdataline,dependingonmodel.Connectingyour

equipmenttothese jacksis optional.Your UPSwillworkproperly

without this connection. Not compatible with PoE (Power Over Ethernet)

applications.

Communications Ports (USB or RS-232): Theseportsconnectyour

UPStoanyworkstationorserver.UsewithTrippLite’sPowerAlert

Softwareandincludedcablestoenableyourcomputertoautomatically

saveopenfilesandshutdownequipmentduringablackout.Alsouse

PowerAlertSoftwaretomonitorawidevarietyofAClinepowerand

UPSoperatingconditions.ConsultyourPowerAlertSoftwaremanual

or contact Tripp Lite Customer Support for more information. See

“USB and RS-232 Serial Communications” in the “Optional

Connections”sectionforinstallationinstructions.

Dry contact communications are simple, but some knowledge of

electronics is necessary to configure them. The DB9 port's pin

assignmentsareshowninthediagram.IftheUPSbatteryislow,the

UPSsendsasignalbybridgingpins1and5.Ifutilitypowerfails,the

UPSsendsasignalbybridgingpins8and5.ToshuttheUPSdown

remotely,shortpin3~pin9foratleast3.8seconds.

EPO (Emergency Power Off) Port: YourUPSfeaturesaEPOport

thatmaybeusedtoconnecttheUPStoacontactclosureswitchto

enableemergencyinvertershutdown.SeeOptionalInstallation.

NEMA 5-15R

NEMA 5-15/20R

Other outlet types not shown

Communications

Basic Operation (continued)

Otros manuales para SmartOnline 2-9USTAND

Tabla de contenidos

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartOnline SU1000RTXL2U Guía de configuración

Tripp Lite

Tripp Lite SmartOnline 3-Phase UPS System SU30K3/3XR5 Manual de usuario

Tripp Lite

Tripp Lite VS450T Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMX700HG Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU5000RT3UHV Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SUINT3000RTXL2U Manual de usuario

Tripp Lite

Tripp Lite BCPERS450 Manual de usuario

Tripp Lite

Tripp Lite SmartPro 3U Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART500USB Manual de usuario

Tripp Lite

Tripp Lite SmartPro AG-03AD Series Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU1000RTXLCD2U Guía de configuración

Tripp Lite

Tripp Lite SmartPro SMX2200XLRT2U Manual de usuario

Tripp Lite

Tripp Lite SMART2500XLHG Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750XL Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU6000RT4UHVHW Guía de instalación

Tripp Lite

Tripp Lite BCPRO850 Guía de configuración

Tripp Lite

Tripp Lite SMART750SLT Manual de usuario

Tripp Lite

Tripp Lite OmniSmart OMNIVSINT500 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline 2-9USTAND Manual de usuario

Tripp Lite

Tripp Lite SU10000RT3UG Manual de usuario

Tripp Lite

Tripp Lite Standby UPS Systems Internet I Manual de usuario

Tripp Lite

Tripp Lite RBC24-SUTWR Manual de usuario

Tripp Lite

Tripp Lite SMX1000LCD Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SUINT3000RTXL2U Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario