Tripp Lite SmartPro AG-03AD Series Manual de usuario

Owner’s Manual

SmartPro®1U Rack-Mount

Intelligent, Line-Interactive UPS Systems

Important Safety Instructions 2

Mounting 3

Quick Installation 4

Optional Installation 6

Basic Operation 7

Storage and Service 10

Battery Replacement 11

Product Registration 12

Español 13

Français 25

Русский 37

Deutsch 49

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

WARRANTY REGISTRATION

automatically entered to win an ISOBAR

surge protector in our monthly drawing!

tripplite.com/warranty

SMX500RT1U

Series: AG-03AD

SMART500RT1U

Series: AG-03AA

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, operation

and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty.

UPS Location Warnings

• Use caution when lifting your UPS. Because of the considerable weight of all rack-mount UPS

systems, at least two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its

vents or fan openings.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a

way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate

the UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

filtered, frequency-regulated, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (sealed Lead-Acid). The batteries are

recyclable. Refer to your local codes for disposal requirements or in the USA only call

1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit www.call2recycle.org for

recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery

Cartridges (R.B.C.). Visit Tripp Lite on the Web at www.tripplite.com to locate the specific

replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of

a blackout or other power interruptions.

• Do not operate UPS without batteries.

• When adding external battery packs to select models with external battery pack connectors,

connect only Tripp Lite-recommended battery packs of the correct voltage and type. Do not

connect or disconnect battery packs when the UPS is operating on battery power.

Mounting

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must

determine the fitness of hardware and procedures before mounting. If hardware and procedures

are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The

procedures described in this manual are for common rack and rack enclosure types and may not

be appropriate for all applications.

4-Post Rack Mounting

UPS models include hardware required to mount in a 4-post rack.

1Attach mounting ears Ato the front

mounting holes of your equipment Busing

the screws provided C. The ears should

face forward.

2Using an assistant if necessary, lift your

equipment and mount it to the rack. Attach

it by screwing the appropriate hardware D

through its mounting ears and into the rack

rails.

2-Post (Telecom) Rack Mounting

Following the procedures below, mount the 1U UPS model in 2-post racks with the included

hardware.

1Attach mounting ears Ato the front

mounting holes of your UPS Busing the

screws provided C. The ears should face

backward.

2Using an assistant if necessary, lift your UPS

and attach it to the rack by passing the

screws, nuts and washers provided D

through its mounting ears and into the rack

rails.

Mounting

Quick Installation

Tower Mounting

Mount UPS models in an upright tower position

using included hardware. The user must

determine the fitness of hardware and

procedures before mounting.

Stand your UPS on its side with the LED/Control

panel at the top. Attach one rack mounting ear

Ato each side of the UPS using included

screws.

1Plug the UPS into an outlet on a

dedicated circuit.*

• Connect the SMX500RT1U AC input to

the outlet using one of the two included

1.8 m C13 to C14 power cords, or

connect with a user-supplied cord.

• SMART500RT1U has an attached cable.

NOTE! after plugging the UPS into a live AC outlet,

the UPS (in “Standby” mode) will automatically

charge its batteries**, but will not supply power to

its outlets until it is turned ON (see Step 3 below).

Note: UPS system will function properly upon

initial startup. However, maximum runtime for the

unit’s battery will only be accessible after it has

been charged for 24 hours.

* See Specifications for circuit amperage

requirements.

** The BATTERY CHARGE LED will be the only LED

illuminated.

1SMX500RT1U Shown

1SMART500RT1U Shown

UNSWITCHED OUTLETS

INPUT

SWITCHED OUTLETSURGE OUTLET

INPUT BREAKER

EPOUSBRS232

ACC.SLOT

Model: SMART500RT1U

Quick Installation

2Plug your equipment into the

UPS.*

• For SMX500RT1U, use the second of the

two included 1.8 m C13 to C14 power

cords to connect equipment to the UPS,

or connect with a user-supplied cord.

• Additional power cords are available from

Tripp Lite. Visit tripplite.com.

* Your UPS is designed to support only electronic

equipment. You will overload the UPS if the

total VA ratings for all the equipment you

connect exceeds the UPS’s Output Capacity

(see Specifications). To find your equipment’s

VA ratings, look on their nameplates. If the

equipment is listed in amps, multiply the

number of amps by your UPS’s voltage to

determine VA.

For example: for SMART500RT1U,

1 amp x 120 V = 120 VA; for SMX500RT1U,

1 amp × 230 V = 230 VA. If you are unsure if

you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

3Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY”

button for one second. The alarm will beep

once briefly after one second has passed.

Release the button.

SMX500RT1U Shown

SMART500RT1U Shown

Optional Installation

These connections are optional. Your UPS will function properly without these connections.

4-5

1USB and RS-232 Serial

Communications

Use the included USB cable (see 1A) and/

or DB9 serial cable (see 1B) to connect the

communication port on your computer to

the communication port of your UPS. Install

on your computer the Tripp Lite PowerAlert

software appropriate to your computer’s

operating system. Your UPS may feature

additional communications ports. These

ports may also be connected to additional

computers which have PowerAlert®software

installed. Consult your PowerAlert manual

for more information.

2EPO Port Connection

This optional feature is only for those

applications which require connection to a

facility’s Emergency Power Off (EPO) circuit.

When the UPS is connected to this circuit, it

enables emergency shutdown of the UPS’s

inverter.

Using the cable provided, connect the EPO

port of your UPS (see 2A) to a user-supplied

normally closed or normally open switch

according to the circuit diagram (see 2B).

Note: The EPO port is not a phone line surge

suppressor; do not connect a phone line to this

port.

SMX500RT1U

Shown

SMX500RT1U

Shown

SMX500RT1U

Shown

Basic Operation

LED Interface

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet*, press

and hold the “ON/OFF/STANDBY” button for one second.** Release the button.

If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and

supply power for a limited time from its batteries***) by pressing and holding

the “ON/OFF/STANDBY” button for one second.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the “ON/OFF/STANDBY” button for one second.** Then unplug the UPS

from the wall outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS (in “Standby” mode) will automatically

charge its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm

will beep once briefly after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: Briefly press and release the “MUTE/TEST”

button.

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold the

“MUTE/TEST” button for two seconds.* Continue holding the button until the

alarm beeps several times and the UPS performs a self-test. See “Results of a

Self-Test” below.

Note: You can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

* The alarm will beep once briefly after the indicated interval has passed.

Results of a Self-Test: the test will last approximately 10 seconds as the UPS

switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to

sound after the test, the UPS’s outlets are overloaded. To clear the overload,

unplug some of your equipment and run the self-test repeatedly until the

“OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no longer

sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

• If the “BATTERY WARNING” LED remains lit and the alarm continues to

sound after the test, the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and repeat the self-

test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires

battery replacement, visit tripplite.com to locate the specific Tripp Lite

replacement battery for your UPS.

Basic Operation

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned ON.

“POWER” LED: This green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, you should save files and shut

down your equipment, since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: This green LED lights continuously whenever the

UPS is automatically correcting high or low AC voltage on the utility line without

the assistance of battery power. The UPS will also emit a slight clicking noise.

These are normal, automatic operations of the UPS; no action is required on your

part.

“OUTPUT LOAD LEVEL” LED: This multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red

(either illuminated continuously or flashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED changes from

red to yellow (or green). CAUTION! Any overload that is not corrected by the user

immediately may cause the UPS to shut down and cease supplying output power

in the event of a blackout or brownout.

“BATTERY CHARGE” LED: When the UPS is operating from utility power, this LED

indicates the approximate charge state of the UPS’s internal batteries: red

indicates the batteries are beginning to charge, yellow indicates the batteries are

roughly midway through charging, and green indicates the batteries are fully

charged. When the UPS is operating from battery power during a blackout or

severe brownout, this LED indicates the approximate amount of energy

(ultimately affecting runtime) which the UPS’s batteries will provide: red indicates

a low level of energy, yellow indicates a medium level of energy, and green

indicates a high level of energy. Since the runtime performance of all UPS

batteries will gradually deplete over time, it is recommended that you periodically

perform a self-test (see “MUTE/TEST” Button description) to determine the energy

level of your UPS batteries BEFORE a blackout or severe brownout occurs. During

a prolonged blackout or severe brownout, you should save files and shut down

your equipment, since battery power will eventually be depleted. When the LED

turns red and an alarm sounds continuously, it indicates the UPS’s batteries are

nearly out of power and UPS shut down is imminent.

“BATTERY WARNING” LED: This LED lights red and an alarm sounds

intermittently after you complete a self-test (See “MUTE/TEST” Button

description) to indicate the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If

the LED continues to light, contact Tripp Lite for service. If your UPS requires

battery replacement, visit tripplite.com to locate the specific Tripp Lite

replacement battery for your UPS.

Basic Operation

Other UPS Features (Rear Panel)

C13

NEMA 5-15R

AC Receptacles: Your UPS features C13 outlets (SMX500RT1U) or NEMA

5-15R outlets (SMART500RT1U). These outlets provide your connected

equipment with AC line power during normal operation and battery power during

blackouts and brownouts. The UPS protects equipment connected to these

receptacles against damaging surges and line noise. If you have a serial or

USB connection to your UPS, you can remotely reboot connected equipment

by turning receptacles OFF and ON using Tripp Lite’s PowerAlert software.

Models also feature outlets labeled “UNSWITCHED” which may not be remotely

turned off.

Communications Ports (USB or RS-232): These ports connect your UPS to

any workstation or server. Use with Tripp Lite’s PowerAlert software and included

cables to enable your computer to automatically save open files and shut down

equipment during a blackout. Also use PowerAlert to monitor a wide variety of

AC line power and UPS operating conditions. Consult your PowerAlert manual or

contact Tripp Lite Customer Support for more information. See “USB and

RS-232 Serial Communications” in the “Optional Installation” section for

installation instructions.

EPO (Emergency Power Off) Port: Your UPS features an EPO port that may be

used to connect the UPS to a contact closure switch to enable emergency

inverter shutdown. See “Optional Installation” section.

Accessory Slot: Remove the small cover panel from this slot to install optional

accessories to remotely monitor and control your UPS. Refer to your

accessory’s manual for installation instructions. Contact Tripp Lite at

tripplite.com/support for more information, including a list of available SNMP,

network management and connectivity products.

Input Breaker(s): Protect an electrical circuit from overcurrent draw from the

UPS load. If one or more breakers trip, remove some of the load, then reset

them by pressing the breaker(s) in.

Ground Screw: Use this to connect any equipment that requires a chassis

ground.

Storage and Service

Storage

Before storing your UPS, turn it completely OFF: With the UPS ON and receiving utility power, press

and hold the “ON/OFF/STANDBY” button for one second (an alarm will beep once briefly after the

interval has passed), then unplug the UPS from the wall outlet. If you store your UPS for an

extended period of time, recharge the UPS batteries once every three months: plug the UPS into a

wall outlet, allow it to charge for 12 hours, and then unplug it and place it back in storage. Note:

after you plug the UPS in, it will automatically begin charging its batteries. However, it will not

supply power to its outlets (see Quick Installation section). If you leave your UPS batteries

discharged for an extended period of time, they will suffer a permanent loss of capacity.

Service

Before returning your UPS for service, follow these steps:

1. Review the installation and operation instructions in this manual to ensure that the service

problem does not originate from a misreading of the instructions. Also, check that the UPS

System’s circuit breaker(s) are not tripped. This is the most common cause of service

inquiries, which can be easily remedied by following the resetting instructions in this manual.

2. If the problem continues, do not contact or return the UPS to the dealer. Instead, contact

Tripp Lite at tripplite.com/support. A service technician will ask for the UPS’s model number,

serial number and purchase date.

3. If the problem requires service, the technician will issue you a Returned Material Authorization

(RMA) number, which is required for service. If you require packaging, the technician can

arrange to send you proper packaging. Securely pack the UPS to avoid damage during shipping.

Do not use Styrofoam beads for packaging. Any damages (direct, indirect, special, incidental or

consequential) to the UPS incurred during shipment to Tripp Lite or an authorized Tripp Lite

service center is not covered under warranty. UPS Systems shipped to Tripp Lite or an authorized

Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on

the outside of the package. If the UPS System is within the 2-year warranty period, enclose a

copy of your sales receipt. Return the UPS for service using an insured carrier to the address

given to you by the Tripp Lite service technician.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartOnline Series Manual de usuario

Tripp Lite

Tripp Lite OMNIVSINT800 Manual de usuario

Tripp Lite

Tripp Lite OMNIPOWER PRO550 Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMX3000XLRT2UA Manual de usuario

Tripp Lite

Tripp Lite SMART1200LCD Manual de usuario

Tripp Lite

Tripp Lite Full Isolation UPS Systems none Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SUPDMB5 Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART700 Manual de usuario

Tripp Lite

Tripp Lite BC Internet Manual de usuario

Tripp Lite

Tripp Lite BCPRO850 Guía de configuración

Tripp Lite

Tripp Lite SmartPro SMART1500 Manual de usuario

Tripp Lite

Tripp Lite SU140KMBPK Manual de usuario

Tripp Lite

Tripp Lite SM750XLNAFTA Manual de usuario

Tripp Lite

Tripp Lite ECO Series Manual de usuario

Tripp Lite

Tripp Lite SU7500RT3U1TF Manual de usuario

Tripp Lite

Tripp Lite OMNISMART OMNIVS500 Manual de usuario

Tripp Lite

Tripp Lite TM500 Manual de usuario

Tripp Lite

Tripp Lite OMNI700LCDT Manual de usuario

Tripp Lite

Tripp Lite SmartPro RMX RMX 1000-2000 VA Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750RTXLCD2U Manual de usuario

Tripp Lite

Tripp Lite AGSM5060 Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART2200RMXL2UP Manual de usuario

Tripp Lite

Tripp Lite AGBC6650 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline 5KVA Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario