TRENDnet TEG-S2620is Manual de usuario

H/W: V1

TEG-S2620is

Quick Installation Guide

Table of Contents

English ......................................................................................................

Troubleshooting .........................................................................................

1. Before You Start

2. Hardware Installation ........................................................................

3. Configure the Switch .........................................................................

................................................................................

Table of Contents

Version 04.04.2009

System Requirements

Optional Equipment

Application

Package Contents

1. Before You Start

English

?Multi-Language Quick Installation

Guide

?User's Guide CD-ROM

?RS-232 cable

?Power Cord

?Rack Mount Kit

?Rubber Feet

TEG-S2620is

?A computer with a network adapter properly installed

?A RJ-45 network cable

Web Browser: Internet Explorer (6 or 7)

?Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,

TEG-MGBS80, TEG-MGBS10D35, TEG-MGBS40D35) for Mini-GBIC slots.

EIA standard 19” rack

24-Port 10/100Mbps Layer 2 Stackable Switch with

2 shared Gigabit Ports and Mini-GBIC Slots

(TEG-S2620is)

RS-232

Workstation with

10/100Mbps PCI Adapter

(TE100-PCIWN)

Workstation

Multi-Mode Fiber

Mini-GBIC Modules

(TEG-MGBSX)

Multi-Mode Fiber

Mini-GBIC Modules

(TEG-MGBSX)

Workstation with

PCI Adapter

(TEG-PCITXR)

1000MbpsFiber 10/100Mbps

2. Hardware Installation

English

2. Connect a RJ-45 network cable

from the computer to an available

Ethernet port on the TEG-S2620is.

3. Verify that the following panel lights

are on: POWER and LINK/ACT.

1. Connect the Power Cord to

the TEG-S2620is and then to a

power outlet.

Note: The Mini-GBIC slots are shared with port 25 and 26 Gigabit Ethernet ports.

When the Mini-GBIC slots are in use, port 25 and 26 Gigabit Ethernet ports are

disabled.

English

3. Configure the Switch

Note: It is recommended that you configure the Switch from a wired computer.

Before the Switch can be configured, a Static IP address must be assigned to

your computer's network adapter in the subnet of 192.168.0.x. Since the

Switch's default IP address is 192.168.0.1, make sure no other network

devices are assigned an IP address of 192.168.0.1. (Refer to Troubleshooting

section on how to configure TCP/IP settings on your PC.)

Web Browser

1. Open your web browser, type

http://192.168.0.1 in the Address

bar, and then press Enter.

3. Select the desired options for

configuring the SNMP switch.

2. Enter the User Name and

Password, and then click OK.

By default:

User Name: admin

Password: admin

English

HyperTerminal

2. Go to Start -> Programs ->

Accessories -> Communications ->

HyperTerminal.

3. Enter a name, choose an icon and

then click OK.

4. Select the correct COM port (e.g.

COM1, COM2) and then click OK.

1. Connect the RS-232 cable from a

serial port on your Windows PC to

the console port on your computer.

English

6. Press Enter.

8. Press Enter.

Your configuration is now complete.

For detailed information regarding the TEG-S2620is’s configuration and

advanced settings, please refer to the Troubleshooting section, User's Guide

CD-ROM, or TRENDnet's website at http://www.trendnet.com.

To ensure the highest level of customer service and support, please take a moment to

Thank you for choosing TRENDnet

To ensure the highest level of customer service and support, please take a moment to

Thank you for choosing TRENDnet

7. Enter the User Name.

By default:

User Name: admin

7. Enter the Password, and then

press Enter. By default:

password: admin

5. Configure the following setting,

click Apply and then click OK:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

Troubleshooting

Q1: How do I configure TCP/IP settings on my computer?

Q2:

A2:

I typed http://192.168.0.1 in my Internet Browser's Address Bar, but an error message

says “The page cannot be displayed.” How can I get into the TEG-S2620is's web

configuration page?

First, check your hardware settings again by following the instructions in section 2.

Second, make sure the Power and LNK/ACT lights are lit. Third, make sure the TCP/IP

settings are configured properly (see Q1). Fourth, since the Switch's default IP address is

192.168.0.1, make sure that no other network devices are assigned an IP address of

192.168.0.1.

1. Go into the Control Panel, click Network and

Internet, click Network and Sharing Center, click

Manage Network Connections and then right-click

the Local Area Connection icon and then click

Properties.

1. Go into the Control Panel, double-click the Network

Connections icon, and then right-click the Local Area

Connection icon and then click Properties.

2. Click Internet Protocol Version 4(TCP/IPv4) and

then click Properties. Then click on Use the

following IP address, and make sure you assign

your network adapter an IP address in the subnet of

192.168.0.x.

Windows Vista

Windows XP/2000

1. Click Internet Protocol (TCP/IP) and then click

Properties. Then click on Use the following IP

address, and make sure you assign your network

adapter an IP address in the subnet of 192.168.0.x.

Q3:

Q4:

Q5:

A5:

If my network's IP is different than the Switch's range, what should I do?

You should still configure the Switch first. After all the settings are applied, go to the Switch's

configuration page, click on Administrator, click IP Configuration, change the IP address of the

Switch to match your network's IP and then click Apply.

What are the default port settings for configuring the Switch through the console port

using HyperTerminal?

Bits per Second: 9600; Data bits: 8; Parity: None; Stop bits: 1; Flow control: None.

I changed the IP address of the switch, but I forgot it. How do I reset my TEG-S2620is?

Follow the instructions below:

1) Connect the RS-232 cable from a serial port on your Windows PC to the console port on

your computer.

2) Go to Start -> Programs -> Accessories -> Communications -> HyperTerminal.

3) Enter a name, select an icon and then click OK.

4) Select the correct COM port (e.g. COM1, COM2) and then click OK.

5) Configure the following settings, click Apply and then click OK:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

6) Press Enter.

7) Enter the user name. By default, the user name is admin.

8) Press Enter.

9) Enter the password. By default, password is admin.

10) Press Enter.

11) Press Tab to navigate to System Reset Configuration and then press Enter.

12) Press Tab to navigate to Factory Default and then press Enter.

13) Press Yto continue.

The default IP address of the switch is 192.168.0.1.

If you still encounter problems or have any questions regarding the TEG-S2620is, please contact

TRENDnet's Technical Support Department.

A3:

Limited Warranty

- 5-Year Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under

normal use and service, for the following lengths of time from the date of purchase.

TEG-S2620is

If a product does not operate as warranted above during the applicable warranty period,

TRENDnet shall, at its option and expense, repair the defective product or deliver to

customer an equivalent product to replace the defective item. All products that are

replaced will become the property of TRENDnet. Replacement products may be new or

reconditioned.

TRENDnet shall not be responsible for any software, firmware, information, or memory

data of customer contained in, stored on, or integrated with any products returned to

TRENDnet pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to

service the product through any unauthorized service center. This warranty is voided if

(i) the product has been modified or repaired by any unauthorized service center, (ii) the

product was subject to accident, abuse, or improper use (iii) the product was subject to

conditions more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDnet office within the applicable

warranty period for a Return Material Authorization (RMA) number, accompanied by a

copy of the dated proof of the purchase. Products returned to TRENDnet must be pre-

authorized by TRENDnet with RMA number marked on the outside of the package, and

sent prepaid, insured and packaged appropriately for safe shipment.

Otros manuales para TEG-S2620is

Tabla de contenidos

Otros manuales de Cambiar de TRENDnet

TRENDnet

TRENDnet TEG-224WS - DATA SHEETS Manual de usuario

TRENDnet

TRENDnet TPE-TG80G Manual de usuario

TRENDnet

TRENDnet TPE-S88 - Web Smart PoE Switch Manual de instrucciones

TRENDnet

TRENDnet TE100-DX16Rplus Manual de usuario

TRENDnet

TRENDnet TI-G80 Manual de usuario

TRENDnet

TRENDnet TFU-430 Manual de usuario

TRENDnet

TRENDnet TE100-SK3 Manual del propietario

TRENDnet

TRENDnet TEG-S081Fi Manual de usuario

TRENDnet

TRENDnet TK-IP101 Manual de usuario

TRENDnet

TRENDnet TI-G102i Manual de usuario

TRENDnet

TRENDnet TEG-160WS Manual de usuario

TRENDnet

TRENDnet TEG-S50TXE SHEETS Manual de usuario

TRENDnet

TRENDnet TK-407K Manual de usuario

TRENDnet

TRENDnet TEG-30102WS Manual de usuario

TRENDnet

TRENDnet TL2-E284 Manual de usuario

TRENDnet

TRENDnet TK-205i Manual de usuario

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Manual de usuario

TRENDnet

TRENDnet TI-PG541i Manual de usuario

TRENDnet

TRENDnet TK-206i Manual de usuario

TRENDnet

TRENDnet TU-400E Manual de usuario

TRENDnet

TRENDnet TEG-S50G Manual de usuario

TRENDnet

TRENDnet TK-217i Manual de usuario

TRENDnet

TRENDnet TEG-S8g Manual de usuario

TRENDnet

TRENDnet TK-1602R Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario