Transition Networks SM24TBT2DPA Manual de usuario

Transition Networks SM24TBT2DPA Quick Start Guide

33736 Rev. D https://www.transition.com Page 1of 2

SM24TBT2DPA

Managed Switch, 24-port Gigabit PoE++, 2-port

SFP/RJ-45 Combo

Quick Start Guide

Transition Networks’ SM24TBT2DPA Switch is a next-generation Ethernet switch offering full L2 features, full PoE

functionality, PoE++ per port output up to 90W. The

Non-Stop PoE

feature lets you upgrade switch firmware or

reboot while retaining PoE power to PDs. Note: see the Install Guide for important Safety Warnings and Cautions,

specifications, features, mounting, connections, grounding, powering, configuration, troubleshooting, regulatory,

service, warranty and tech support Information.

LED Descriptions: The front panel LEDs provide switch status checking and monitoring.

SYS (System) LED: indicates if the switch is powered up correctly or if there is a system alarm triggered.

Mode LEDs: indicate the mode of all RJ45/SFP ports on the switch. You can press the Mode/Reset button

sequentially to switch between the two different modes (Link/Activity/Speed mode and PoE mode).

Port Status LEDs: indicate the current status of each RJ45/SFP port. You can check these LEDs for port status in

different modes after changing the mode by pressing the Mode/Reset button.

Press the Mode/Reset button for less than 2 seconds to change LED mode (Link/Act/Speed Mode or PoE Mode);

you can then check the port status by reading the LED behaviors per the Install Guide.

Mode/Reset Button: Press the front panel Mode/Reset Button for a period of time to:

Change LED Mode: Press the button for 0 ~ 2 seconds; the SYS LED is ON Green; the Port Status

LED status changes based on the mode selected.

Reset the Switch: Press the button for 2 ~ 7 seconds; the SYS LED blinks Green; all port Status LEDs

are Off.

Restore to Defaults: Press the button for 7 ~ 12 seconds; the SYS LED blinks Green; all port Status LEDs are On.

Back Panel: The back panel provides for dual hot-swappable 1560W power supplies for powering the switch.

The switch ships with one power supply (780 Watts) standard; use a secondary power supply module (1560

Watts) if the full 90 Watts output is needed on all ports.

Package Contents: Check the package contents to make sure you have received the one Switch with a Power

Supply installed, one AC Power cord, a second Power Supply (Optional), one RJ-45 to DB-9 cable, and four rubber

feet.

Install SFP Modules: Do not look into laser ports. 1. Position the SFP at either install slot with

the SFP label facing correctly. 2. Carefully slide the SFP device into the slot, aligning it with the

internal installation guides. 3. Press firmly so the SFP firmly seats against the internal mating

connector. 4. Attach an appropriate cable into the SFP module port. 5. Attach the other end of

the cable into the other device.

Grounding: ATTENTION: This case must be grounded. No DC input may be earth grounded. Use

Isolated Power Supply. Note: The switch is an indoor device. If it used with outdoor devices such

as outdoor IP cameras or outdoor WAPs, then you should install a surge protector or surge

suppressor in order to protect the switch.

Transition Networks SM24TBT2DPA Quick Start Guide

33736 Rev. D https://www.transition.com Page 2of 2

Connecting to Power: CAUTION! Hazardous Area: Do Not remove this cover. Trained service people only. No

serviceable components inside. CAUTION: Hot Surfaces. WARNING: For continued protection against risk of fire,

replace only with same type and rating of fuse. Note the sticker indicating “To Keep Warranty Please Do NOT

Remove”. Warning: Class I Equipment. This equipment must be earthed. The power plug must be connected to a

properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on

accessible metal parts. Warning: shock hazards exist that can result in serious injury or death if safety instructions

are not followed. Note: This product is to be connected only to UL listed PoE networks and without routing to the

outside plant. Power Connection Warning:Connect the power supply to the switch first, and then connect the

power supply to power. Otherwise catastrophic product failure may occur. 1. Verify that power is off to the DC

circuit that you are going to attach to the switch PoE DC-input connector. This can be either of the two power

supplies (AC-input or DC-input) or site source DC. 2. As an added precaution, place an appropriate safety flag and

lockout device at the source power circuit breaker, or place a piece of adhesive tape over the circuit breaker

handle to prevent accidental power restoration while you are working on the circuit. Power Disconnection: To

disconnect power from the switch after a successful boot: 1. Turn off power to the switch. 2. Disconnect the

cables.

Connect the AC Power Cord: Warning: Risk of electrical shock.

Warning: Shock/damage hazard exists if power supply is installed / removed while

powered on. 1. Refer to the “Grounding” section above. 2. Remove the blank faceplate

or use the one open power supply slot. 3. Fasten the AC Power Supply with the slotted

retaining screw. 4. Insert the provided AC Power plug into the switch AC receptacle

(power inlet). 5. Connect the other end of the AC power cord to the AC power outlet. 6.

Check that the AC OK and DC OK LEDs are lit.

Initial Switch Config via Web Browser: 1. Connect the PC Ethernet RJ45 connector to the switch via standard

Ethernet LAN cable. 2. Power up the PC to be used for initial config. 3. Reconfigure the PC’s IP address and Subnet

Mask so it can communicate with the switch. 4. Power up the switch to be initially configured and wait until it has

finished its start-up processes. 5. Connect the PC to any port on the switch using a standard Ethernet cable; make

sure the switch port LED is lit. 6. In a Web browser, enter the switch default IP address (192.168.1.77) and Subnet

Mask (255.255.255.0). The Login page should display. 7. Enter the factory default username (admin) and

password (admin) on the Login page. 8. Click the “Login” button to log into the switch. See the

Web User Guide

for more information.

Initial Switch Config via CLI: 1. Use an RJ-45 cable to connect a terminal or PC/terminal emulator to the switch

port to access the CLI. 2. Attach the RJ-45 serial port on the switch front panel to the cable for Telnet/CLI

configuration. 3. Attach the other end of the DB-9 cable to a PC running Telnet or a terminal emulation program

such as HyperTerminal or TeraTerm. 4. After powering up the switch for the first time, you can perform the initial

switch configuration using the CLI (Command Line Interface). See the

CLI Reference

for other switch features.

| toll free: 1.800.526.9267 | fax: 952.941.2322 | web: https://www.transition.com

Otros manuales para SM24TBT2DPA

Tabla de contenidos

Otros manuales de Cambiar de Transition Networks

Transition Networks

Transition Networks mil-sm8dpa Manual de usuario

Transition Networks

Transition Networks SM24T6DPA Manual de usuario

Transition Networks

Transition Networks SISTF10xx-130-LR(T) Manual de usuario

Transition Networks

Transition Networks SISGM1040-284-LRT Manual de usuario

Transition Networks

Transition Networks Milan MIL-SM8002TG Manual de usuario

Transition Networks

Transition Networks SISTM1040-262D-LRT-B Instrucciones de funcionamiento y mantenimiento

Transition Networks

Transition Networks E-FL-HB-0400 Manual de usuario

Transition Networks

Transition Networks SISTF1010-180-LRT Manual de usuario

Transition Networks

Transition Networks E-TBT-HB-0400 Manual de usuario

Transition Networks

Transition Networks SISPM1040-3248-L Instrucciones de funcionamiento y mantenimiento

Transition Networks

Transition Networks SISPM1040-582-LRT Manual de usuario

Transition Networks

Transition Networks SM TAT4X Series Manual de usuario

Transition Networks

Transition Networks SM24DPa Manual de usuario

Transition Networks

Transition Networks SM24DPa Manual

Transition Networks

Transition Networks MIL-S800I-V2 Manual de usuario

Transition Networks

Transition Networks SM24DP4XA Manual de usuario

Transition Networks

Transition Networks SM8TAT2SA-DC Manual de usuario

Transition Networks

Transition Networks SISPM1040-3 L Series Manual de usuario

Transition Networks

Transition Networks MIL-SEM24T4GPA Manual de usuario

Transition Networks

Transition Networks SISGM1040-184D-LRT Manual de usuario

Transition Networks

Transition Networks SM24TBT2DPA Manual de usuario

Transition Networks

Transition Networks SM24TAT4GPA Manual de usuario

Transition Networks

Transition Networks SM TAT4X Series Manual de usuario

Transition Networks

Transition Networks SM24T6DPA Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario